CD4011BM96
Product Specifications
CD4011BM96
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4011BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4011BM96: four NAND gates on a 2500 piece reel
CD4011BM96 is the tape and reel member of the CD4011B family, four 2-input NAND gates with buffered inputs and outputs on a 3 V to 18 V CMOS process, in a 14-lead SOIC, 2500 pieces on a large reel. The vendor document is SCHS021D revision D, shared with the CD4012B and the CD4023B, and the descriptor on the product page is four channels, two inputs per channel, 3 V to 18 V. The die is the same one that the plastic DIP carries, so the electrical numbers are the family numbers; what changes here is how the part arrives at the line.
The addendum lists CD4011BM96 as Active in production, SOIC (D) with 14 leads, 2500 pieces on a large tape and reel, RoHS yes with a nickel-palladium-gold finish, moisture sensitivity level 1 at a 260 degree peak with unlimited floor life, minus 55 to plus 125 degrees, and the marking CD4011BM. The same body appears on the BM row at 50 pieces in a tube, and the obsolete BMT row of the same body is still printed in the document with a blank quantity and a Call TI instruction, which is the row that grey market stock tends to be listed against.
The CD4011BM96 row as the vendor addendum publishes it
| Part class | Quad 2-input NAND gate, buffered inputs and outputs |
| Vendor descriptor | Four channels, two inputs per channel, 3 V to 18 V |
| Vendor document | SCHS021D revision D, CD4011B, CD4012B and CD4023B |
| Supply range | 3 V to 18 V |
| Propagation delay, vendor figure | 60 ns typical at 10 V into a 50 pF load |
| Output drive, parametric table | 6.8 mA sink and source |
| Data rate, parametric table | 8 Mbps |
| Input current, maximum | 1 microamp at 18 V over the full range, 100 nA at 18 V and 25 degrees |
| Quiescent current | Tested to maximum at 20 V on every unit |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| Package for this code | SOIC (D), 14 leads |
| Packing | 2500 pieces on a large tape and reel |
| Lead finish | NIPDAU |
| Moisture level | Level 1, 260 degrees peak, unlimited floor life |
| Operating range | Minus 55 to plus 125 degrees |
| Status | Active, production |
| Part marking | CD4011BM |
| Reel rows in the addendum | CD4011BM96, CD4011BM96.A and CD4011BM96E4, all 2500 pieces |
| Tube member of the same body | CD4011BM, 50 pieces |
| Obsolete rows | CD4011BMT and CD4011BPW, quantity blank, Call TI |
| TSSOP row | CD4011BPWR, 2000 piece reel, marking CM011B |
| SOP row | CD4011BNSR, 2000 piece reel |
Reel handling and the feeder decision
A 2500 piece reel is the format a placement machine wants and the format a small build does not. The practical split is at the feeder setup: a line that keeps the part loaded across several work orders prefers the reel, while a line that loads by hand for a few hundred boards finds the 50 piece tube easier to manage, even though the per piece cost is higher. Because the body is level 1 at a 260 degree peak, neither format needs a bake, and a partial reel can go back to stock with the leader taped and the label kept with it.
The marking is CD4011BM on the reel as well as on the tube, which is worth knowing at receiving: the die marking does not change with packing, so a reel labelled BM96 will still read BM on the body. The reel label is what carries the BM96 string and the 2500 piece quantity, and a label that reads BM is either a tube repacked onto a reel or a mislabelled consignment, and both are worth stopping at goods in.
The four gates and what they are usually asked to do
The delay is 60 ns typical at 10 V into 50 pF, the drive is 6.8 mA in both directions, the input leakage is 100 nA at 25 degrees and 1 microamp over the range, and the quiescent current is tested to maximum at 20 V on every unit. Four gates in one body cover the two most common 4000B idioms: the cross coupled latch made from two NANDs, which holds a state without a clock and debounces a switch with one resistor and one capacitor per side, and the inverter made by tying both inputs of a gate together, which leaves two gates for the logic term itself.
The buffered output stage is what makes the gate usable as a driver as well as a logic element. A 6.8 mA output can sink an LED at 3 mA with a series resistor and still leave the other three gates for the circuit, and it can pull a 1 k resistor to a rail fast enough that the 60 ns delay dominates the edge rather than the load. What it cannot do is drive a capacitive load of several hundred picofarads at speed, because the delay figure is quoted at 50 pF and rises with load.
Where the reel member sits in the family
The reel also settles the question of what a spare package is worth. A tube of 50 in a service kit is convenient and a reel of 2500 is not, so a repair department keeps a small tube stock while the line runs from the reel, and both come from the same die. The two packings are not interchangeable on the paperwork either: a build that buys a reel has to record a 2500 piece receipt, and a build that buys tubes records fifty lines of fifty, which is the kind of difference that shows up in a stock audit rather than on the board.
The family covers four bodies: the PDIP at 25 to a tube, the SOIC at 50 to a tube and 2500 to a reel, the SOP at 2000 to a reel, and the TSSOP at 2000 to a reel with the CM011B marking. The TSSOP row is the one for a board with no room for an 8.65 mm body, and the SOP row is the 1.27 mm pitch alternative that some lines prefer for inspection. Only the SOIC and the TSSOP rows are active at a 2000 or 2500 quantity; the PDIP is a 25 piece tube format that suits repair and prototype work.
Across functions the substitutes are the CD4012B for 4-input NAND and the CD4023B for 3-input NAND, both in the same document, and the CD4001B when the function is NOR. All share the process, the supply range and the 6.8 mA drive except the 4023, whose parametric table prints 1.5 mA and should be checked before it is used as a driver.
Incoming checks on a reel delivery
Three checks matter on a reel of logic. The label should read CD4011BM96 with a 2500 piece quantity and a date code inside the customer window. The body marking should read CD4011BM, which is expected and not a mismatch. The third check is a first article function test from the first pocket of the reel, because a reel that has been spliced or repacked can carry a different date code in the middle of the run even when the label is correct.
The reference pages are the incoming inspection plan, date code management, and the BOM scrubbing route when the bill of materials still carries the tube code after the line has moved to a reel.
Questions that come up on this reel code
Whether a BM96 reel can serve a build that only needs 600 pieces. It can, but the remaining 1900 pieces become stock that has to be stored and tracked, and a tube order may be the cheaper answer for a one off build.
Whether the E4 row is different. The E4 suffix is a packing and materials variant of the same body, listed at the same 2500 pieces, and it changes the declaration rather than the electrical behaviour.
Whether the part can be run at 15 V. It can, and the 60 ns figure is quoted at 10 V, so a 15 V circuit is faster and a 5 V circuit is slower than the printed number.
Whether the obsolete BMT row is a hazard. It is, because the body marking is the same as the active row, so the only defence is the date code and the supplier record rather than the label on the part.