Contact Us

CD4001BM96

Brand: Texas Instruments
Texas Instruments CD4001BM96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4001BM96 — Power Management & Signal Chain | Superb Automation

CD4001BM96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4001BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4001BM96: four NOR gates on a 2500 piece reel

CD4001BM96 is the tape and reel member of the CD4001B family, four 2-input NOR gates with buffered inputs and outputs on the 3 V to 18 V CD4000B process, in a 14-lead SOIC, 2500 pieces on a large reel. The vendor document is SCHS015C revision C, shared with the CD4002B and CD4025B, and the descriptor on the product page is the same four channels, two inputs per channel, 3 V to 18 V. The difference between this code and the CD4001BM is packing alone, and the difference between a reel and a tube is a production decision rather than an electrical one.

The addendum lists CD4001BM96 as Active in production, SOIC (D) with 14 leads, 2500 pieces on a large tape and reel, RoHS yes with a nickel-palladium-gold finish, moisture sensitivity level 1 at a 260 degree peak with unlimited floor life, minus 55 to plus 125 degrees, and the marking CD4001BM on the body. The reel suffix is the part that a placement machine consumes, and the same body appears on three rows of the addendum: BM96 and BM96.A at 2500 pieces, BM96G4 at 2500 with the green compound, and the plain BM at 50 pieces in a tube.

The CD4001BM96 row as the vendor addendum publishes it

Part classQuad 2-input NOR gate, buffered inputs and outputs
Vendor descriptorFour channels, two inputs per channel, 3 V to 18 V
Vendor documentSCHS015C revision C, CD4001B, CD4002B and CD4025B
Supply range3 V to 18 V
Propagation delay, vendor figure60 ns typical at 10 V into a 50 pF load
Output drive, parametric table6.8 mA sink and source
Data rate, parametric table8 Mbps
Input current, maximum1 microamp at 18 V over the full range, 100 nA at 18 V and 25 degrees
Quiescent currentTested to maximum at 20 V on every unit
Package for this codeSOIC (D), 14 leads
Packing2500 pieces on a large tape and reel
Lead finishNIPDAU
Moisture levelLevel 1, 260 degrees peak, unlimited floor life
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4001BM
Reel rows in the addendumCD4001BM96, CD4001BM96.A and CD4001BM96G4, all 2500 pieces
Tube member of the same bodyCD4001BM, 50 pieces
Obsolete row of the same bodyCD4001BMT, quantity blank, Call TI
SOP memberCD4001BNSR, 2000 piece reel, last time buy
TSSOP memberCD4001BPWR, 2000 piece reel, marking CM001B

Reel economics on a 2500 piece quantity

A reel of 2500 is the same material as fifty tubes of 50, and the arithmetic that matters on the floor is which format survives a shift without a reload. Fifty tubes take about fifty feeder changes on a hand loaded line, which is a morning of work on a single part number, while one reel takes one. On a build of a few hundred boards the tube still wins because the unused part of a reel is 2000 pieces sitting in stores, and on a repeat build the reel wins because the part is already where the machine needs it.

A 2500 piece reel is a build quantity, not a prototype quantity. At one gate package per board it covers 2500 boards, and the arithmetic that decides between the reel and the tube is the setup cost of a feeder against the cost of carrying the leftover. A line that runs the same board every month keeps the reel on the machine; a line that builds five different boards a month pays the feeder setup each time and may be better served by the tube.

The reel also changes the handling rules. A large reel is heavy enough to need a proper feeder and a splice check, and the tape orientation has to match the machine setup, which is the one place where a BM96 can go wrong despite being electrically identical to the BM. The level 1 rating removes the bake step, so the practical sequence is open the reel, load the feeder, verify the first article, and run.

The electrical envelope this reel carries

Because the die is the same, the numbers are the family numbers: 60 ns typical at 10 V into 50 pF, 6.8 mA sink and source, 100 nA of input current at 25 degrees and 1 microamp over temperature, noise margin of 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V, and a quiescent current that is tested to maximum at 20 V on every unit. The 8 Mbps data rate in the parametric table is the vendor's way of expressing the same 60 ns delay, and it is a reminder that this is a slow logic family by modern standards: a 10 MHz clock edge passed through two gates already carries 120 ns of delay, which is a phase shift rather than a propagation detail in a control loop.

What the slow family buys is the reason it is still stocked. Static current is in the microamp range, the input impedance is high enough for a 1 megohm pull, the output swing is symmetric about the rails, and the part works from 3 V to 18 V with the same pinout. On a board that has to survive a 12 V transient and still interface to a 5 V microcontroller, a 4000B gate is often the cheapest way to do the level shift and the logic in one part.

Where the reel member sits in the family

Three bodies and five packings make up the CD4001B range in the addendum: the PDIP at 25 to a tube, the SOIC at 50 to a tube and 2500 to a reel, the SOP at 2000 to a reel on a last time buy row, and the TSSOP at 2000 to a reel. The ceramic CDIP rows sit outside that set and carry the high reliability screening. For a reflow line the reel SOIC is the default, and the tube SOIC exists for the small build that does not justify a feeder setup.

Across functions the substitutes are the CD4002B for 4-input NOR, the CD4025B for 3-input NOR and the CD4011B for NAND, all in the same document and all on the same process. A board that needs both NOR and NAND usually takes one reel of each rather than trying to build an inverter from a spare gate, because the parts cost less than the board area the workaround consumes.

Incoming checks and the reel paperwork

On a reel order the paperwork matters as much as the part. The reel label carries the quantity, the lot and the date code, and a mismatch between the label and the purchase order string is the most common receiving finding on these parts. The body marking should read CD4001BM, since the die marking does not change between the tube and the reel, and the G4 row should be checked if a green compound was specified.

The pages behind those checks are the incoming inspection plan, date code management, and the BOM scrubbing route when a bill of materials still carries the tube code and the build has moved to a reel.

Questions that come up on the reel code

Whether the BM96 can be used where the BOM says BM. Electrically yes, because the die and the body are identical, but the packing has to be accepted by the line and the purchase order should name the reel code so the quantity is not split into 50 piece tubes.

Whether a partial reel can be returned to stock. It can, with the leader taped and the label kept with the reel, and because the part is level 1 there is no floor life to reset.

Whether the G4 row is a different part. It is the same body and die with a green mould compound, and it is listed at the same 2500 piece quantity, so the choice is a materials declaration question rather than an electrical one.

Whether the reel suits a 3.3 V board. The supply range starts at 3 V, so it runs, but the delay and the drive at 3.3 V are below the 10 V figures printed on the product page, and the margin should be checked against the 5 V table rather than assumed from the 10 V number.