Contact Us

CC2640R2FRGZR

Brand: Texas Instruments
Texas Instruments CC2640R2FRGZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC2640R2FRGZR — Power Management & Signal Chain | Superb Automation

CC2640R2FRGZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC2640R2FRGZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC2640R2FRGZR Bluetooth 5.1 low energy wireless MCU in the 7 by 7 mm 48 pin VQFN body

The CC2640R2FRGZR is the same silicon as the small body member of the CC2640R2F family, in the 7 by 7 mm VQFN48 package with 31 GPIO. Customers move to this body when the application needs pins rather than when it needs features: the core, the radio, the memory and the current figures are identical to the 4 by 4 mm part, and only the package and the number of available pins change. It is also the body that is pin compatible with the CC2642R and CC2652R, which matters for a product that may need more flash later.

Reading the family as one device with four bodies is the practical way to use it. The 2.7 by 2.7 mm DSBGA34 carries 14 GPIO, the 4 by 4 mm VQFN32 carries 10, the 5 by 5 mm VQFN32 carries 15 and the 7 by 7 mm VQFN48 carries 31. The trade is always board area against pins, and the electrical and radio behaviour does not change with the body, so a firmware image moves across the family with a pin mapping change and no radio retest in most cases. That is what makes the family usable in a product line where one board is a sensor and the next is a gateway.

Key parameters taken from the CC2640R2FRGZR document

ProcessorArm Cortex M3 at 48 MHz, CoreMark score 142, with a separate Cortex M0 radio core and a 16 bit sensor controller
Memory275 KB of non volatile memory including 128 KB of in system programmable flash, up to 28 KB of system SRAM with 20 KB ultra low leakage, and 8 KB of SRAM usable as cache
Radio2.4 GHz transceiver compatible with Bluetooth 5.1 and earlier low energy specifications, with LE Coded PHY and LE 2 Mbit PHY
SensitivityMinus 97 dBm at 1 Mbps, minus 103 dBm on the 125 kbps LE Coded PHY, with a 102 dB link budget
Output powerProgrammable up to +5 dBm
Current5.9 mA receive, 6.1 mA transmit at 0 dBm, 9.1 mA transmit at +5 dBm, 61 microamps per MHz on the core, 1.1 microamps standby, 100 nA shutdown
Supply1.8 to 3.8 V normal operation, 1.7 to 1.95 V in external regulator mode, with an on chip DC to DC converter
GPIO31 pins, every digital peripheral routable to any GPIO
Pin compatibilitySame footprint as the CC2642R and CC2652R in the 7 by 7 mm body, which allows a later move to more flash without a board change
Peripherals12 bit 200 ksample per second ADC, four timer modules, UART, I2C, I2S, two SSI ports, AES 128 accelerator, true random number generator, capacitive sensing, temperature sensor
BodyVQFN 48 pins, 7 by 7 mm, 0.5 mm pitch
Order code factsCC2640R2FRGZR, VQFN RGZ 48 pins, 2500 pieces on a large reel, NIPDAU finish, moisture level 3 with a 168 hour floor life, minus 40 to plus 85 C; the T suffix is the 250 piece small reel

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The 31 GPIO is what makes this body the choice for a product with a display, a keypad and several sensors. Even so, the pin budget fills quickly on a real board: the debug port takes two, the crystals take four, the SPI flash takes four if the product boots from external memory, the radio front end takes one or two, and a parallel display can take a dozen. The value of the larger body is not that it has spare pins but that a product can be built without a port expander, and a port expander on an I2C bus is a part that costs money and adds a failure mode.

The pin compatibility with the CC2642R and CC2652R is the feature to plan around. The CC2640R2F has 128 KB of flash, which is enough for one application image plus an over the air update image if the update is compressed or streamed. A product that grows a second protocol, a larger log or a display library can move to the CC2652R in the same footprint with more flash and more RAM, keeping the board and the RF network. That path only exists in this body, so a product with a long life should start here rather than in the 4 by 4 mm part.

Radio behaviour does not change with the body, which is convenient and also a trap. The matching network sits outside the package, but the package parasitics and the ground return path do change, and the reference network for the 4 by 4 mm body does not necessarily land at the same delivered power in the 7 by 7 mm body. On a product that has to pass a regulatory limit, the antenna and the filter are retuned on the final body, even when the silicon is the same and the firmware is unchanged. The 7 by 7 mm body has more room around it on the board, which usually makes the matching easier and the thermal path shorter.

The DC to DC converter inside the part is a switching stage, and it is the one place where the arrangement of the board affects the radio. The inductor and the decoupling capacitors belong close to the package, the ground pour under the part has to be continuous, and the switching node has to be kept away from the crystal and the antenna feed. On a 4 layer board with a proper ground plane this is straightforward. On a two layer board the converter is often the reason a link works on the bench and fails in the field, because the switching current returns through a path that also carries the radio ground.

  • Pin count with the display, the debug port, the crystals and the flash accounted for, before the board is committed.
  • Average current over a duty cycle, since the larger body does not change the radio but does change the number of peripherals left powered.
  • Antenna delivered power and harmonic level on the final body, because the matching does not transfer between packages without checking.
  • Standby current with the flash in deep power down and the display held off, which is where the 1.1 microamp figure is either kept or lost.
  • Over the air update time and the flash headroom for two images, since the 128 KB is shared with the stack.
  • Thermal rise on the part at full transmit duty, because the larger body has a better path to the board but the radio still dissipates.

Which projects this part fits

This part fits gateways that need a display and several radios on one board, medical monitors with a graphic panel, industrial sensors with a keypad, access control terminals and products that sell in several configurations from one board. It also fits any product that may need the CC2652R later, because the footprint allows that move without a board revision. Customers who build a family of products from one board library keep this body as the common platform and use the smaller bodies only where the enclosure forces it.

Questions that come up before a purchase order is released

Is this the same firmware as the 4 by 4 mm part?

Yes for the radio and the core, with one caveat. The pin mapping differs, so every peripheral assignment and every GPIO number changes, and any board support package has to be regenerated. The protocol stack, the sensor controller program and the application logic move across unchanged. In practice a product that starts on the small body and moves to this one spends its time on the pin map and the board bring up, not on the radio.

Does the larger body run cooler?

It has a better thermal path because the exposed pad is larger and the board around it carries more copper. The radio current is the same, so the junction rise is lower for the same board temperature. On a product that transmits continuously, for example a continuous advertising beacon in a sealed enclosure, the difference is measurable and can decide whether the part stays inside its ambient rating.

What is the practical difference between the R and T order codes?

The reel size only. The R suffix is 2500 pieces on a large reel and the T suffix is 250 pieces on a small reel, with the same body, the same marking family and the same moisture level. A prototype build can use the small reel and a production build the large one, and there is no electrical difference between them.

Can the part be powered from 3.3 V directly?

Yes in normal operation, where the supply window is 1.8 to 3.8 V and the internal converter produces the core rail. It cannot be powered from 3.3 V while it is configured for external regulator mode, because that mode expects 1.7 to 1.95 V and the part will be damaged. The mode is set by firmware and by the board, and the two have to agree before the first power up.

How is the part checked at incoming inspection?

Reel and moisture bag check, marking check, and a functional connect test on a known good board with the production firmware. The radio itself needs a shield box to measure, and most customers test the assembled product rather than the part. We keep the test firmware version with the lot, because a stack upgrade changes the connect timing without any change to the silicon, and a lot that fails against an older baseline is not necessarily a bad lot.

How SUPERB handles this line

We supply the CC2640R2FRGZR with the same lot and date code traceability as the rest of the family, and we confirm the reel size on the order because the R and T suffixes carry the same part in different quantities. The MCU cross reference page lists the wireless families and their package options, RF component sourcing covers the matching and front end parts that sit around a 2.4 GHz radio, and component lead time solutions is the page to read when a build is waiting on a package that the distributor does not stock.