Contact Us

HMC459-Die

Brand: Analog Devices
Analog Devices HMC459-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC459-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC459-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC459-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC459-Die: 17 dB of gain to 18 GHz and the 2.32 W of dc that pays for it

The HMC459-Die is a GaAs PHEMT MMIC distributed power amplifier in die form, specified from dc to 18 GHz with 17 dB of gain, +25 dBm of output power at 1 dB compression and +31.5 dBm of output third order intercept, from 290 mA at a +8 V supply. It is a driver amplifier, not a final stage: the numbers that decide whether it fits a build are the dc power it burns on a 3.12 mm by 1.63 mm piece of GaAs and the way its gain falls from 18.5 dB at the bottom of the band to 12 dB at the top.

Published values

ParameterValue
Frequency rangedc to 18 GHz
Gain17 dB typical, 18.5 dB to 2 GHz and 12 dB at 18 GHz
Gain flatnessplus or minus 0.75 dB over the band
Gain variation over temperature0.02 to 0.045 dB per degree C
Output power at 1 dB compression+25 dBm typical
Saturated output power+26.5 dBm typical
Output third order intercept+31.5 dBm typical
Noise figure3.0 dB low band, 6.5 dB at 18 GHz
Supply+8 V at 290 mA, Vgg2 at 3 V
Gate biasVgg1 between -2 V and 0 V, set for Idd = 290 mA
Input and output match50 ohm, internally matched
Die size3.12 mm x 1.63 mm x 0.1 mm

The dc budget is 2.32 W before any signal is applied

Eight volts at 290 mA is 2.32 W of quiescent dissipation. At the +25 dBm compression point the output is 316 mW, which is 13.6 percent of that dc figure, and at the +26.5 dBm saturated point the output is 447 mW, which is 19.3 percent. Those two numbers are the whole efficiency story of this part and they are the reason it is used as a driver ahead of a higher power stage rather than as the last device in a chain.

The die is 3.12 mm by 1.63 mm, or 5.09 square millimetres, so the same 2.32 W is 456 mW per square millimetre. A die that small has no package to spread heat: the thermal path is the die attach and the carrier under it, and that carrier is part of the electrical build rather than a mechanical detail. A 0.1 mm thick die on a well bonded carrier in a multi chip module runs far cooler than the same die on a thin film with a void under it, and the gain variation of 0.045 dB per degree C at the top of the band turns a 40 degree C difference into 1.8 dB of gain.

Why the bond wire length appears in the specification

The data sheet states that all numbers are taken with the chip in a 50 ohm fixture connected by 0.025 mm diameter wire bonds of 0.31 mm minimum length. That sentence is a specification, not a note. A 0.31 mm length of 25 micron gold wire is roughly 0.3 nH, which is about 34 ohm of reactance at 18 GHz against a 50 ohm system, and a longer loop adds more of both inductance and loss. The 12 dB of gain quoted at 18 GHz belongs to that short loop.

Practical consequence for a multi chip module: the launch has to be planned so the ribbon or wire can be kept near 0.31 mm, which usually means the die is placed hard against the transmission line rather than in the middle of a cavity. If a longer bond is unavoidable, expect the top of the band to lose gain and return loss faster than the middle of the band, and plan the gain budget with the 12 dB figure and not the 17 dB headline.

Gain falls 6.5 dB across the band and the noise figure rises 3.5 dB

The family table gives 18.5 dB typical from dc to 2 GHz, 18 dB to 6 GHz, 17 dB to 10 GHz and 12 dB to 18 GHz, with the noise figure moving from 3.0 dB to 6.5 dB over the same span. A receive chain that uses this part at the front has to be budgeted at the top of the band, because a 3.5 dB rise in the first stage is a 3.5 dB rise in the system noise figure unless a filter or a limiter in front of it already dominates.

Typical uses are electronic warfare and countermeasure chains, radar drivers, microwave radio and VSAT, military and space equipment and test instrumentation, which is the same list the vendor prints. In every one of those the part is chosen for bandwidth and linearity together: +31.5 dBm of intercept at 17 dB of gain means the output intercept is close to 14 dB above the compression point, so a two tone test at 8 dB backoff is where the part is comfortable.

Two pages worth reading before a purchase order goes out are defense grade components and the ADI second source page; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.

Two questions buyers ask

Does the die need a heat sink? It needs a thermal path, which in die form means the carrier and the die attach rather than a heat sink. 2.32 W over 5.09 square millimetres has to leave through the bottom of the die, so the carrier material, the void content under the die and the copper it sits on decide the junction temperature. In a sealed module at 70 degree C ambient the die temperature, not the ambient, is what the 0.045 dB per degree C gain drift is measured against.

Is Vgg1 a fixed -0.5 V? No. The data sheet lists -0.5 V as the typical value that produces the specified 290 mA, and the footnote says Vgg1 is adjusted between -2 V and 0 V to reach that current. It is a depletion mode PHEMT, so the gate bias is the current setting and each assembly is biased to the same drain current rather than to the same gate voltage.