Contact Us

HMC7149-Die

Brand: Analog Devices
Analog Devices HMC7149-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC7149-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC7149-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC7149-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC7149-Die: 10 W of gallium nitride from 6 GHz to 18 GHz, on a copper tungsten carrier

The HMC7149-Die is a gallium nitride monolithic power amplifier chip specified from 6 GHz to 18 GHz with 10 W saturated output, 20 dB of small signal gain and 39.5 dBm of output third order intercept from a 28 V supply at 680 mA. It is matched to 50 ohm at both ports and is measured with the die eutectically attached to a 1.02 mm copper tungsten carrier, which is part of the specification rather than a convenience.

Published values

ParameterValue
Frequency range6 GHz to 18 GHz
Saturated output power40 dBm typical
Power gain at saturation10 dB
Small signal gain20 dB typical
Output third order intercept39.5 dBm at 28 dBm output per tone
Supply28 V at 680 mA
Input and output match50 ohm, internally matched
Processgallium nitride on silicon carbide
Die size3.4 mm x 4.5 mm x 0.1 mm
Assemblyeutectic attach to a 1.02 mm copper tungsten carrier, 1.0 mil ball bonds

Nineteen watts in, ten watts out

28 V at 680 mA is 19.04 W of dc input. At saturation the output is 40 dBm, or 10 W, which is 52 percent drain efficiency. The efficiency column in the same table quotes about 35 percent, so the 35 percent belongs to a point below saturation or to a narrower part of the band, and the two numbers are not in conflict once the operating point is stated.

For a buyer the useful arithmetic is that 10 W out of a 19 W budget leaves 9 W of heat in a die of 15.3 square millimetres. That is 0.59 W per square millimetre of gallium nitride, and it is the reason the carrier is a metal rather than a laminate.

Why the carrier is in the datasheet

The measurement condition is a eutectic attach to a copper tungsten carrier 1.02 mm thick. Copper tungsten is chosen because its thermal expansion is close to the gallium arsenide and gallium nitride it carries, so the joint survives thermal cycling, and because its thermal conductivity is high enough to spread the heat before it reaches the housing.

A module built on a different carrier will measure differently, and not only in temperature. The electrical reference planes and the bond wire lengths to the 50 ohm lines are set by the carrier geometry, so a replacement carrier is a new radio frequency assembly rather than a mechanical change.

The 1.0 mil ball bonds

The radio frequency connections are made with 1.0 mil ball bonds to 50 ohm transmission lines on alumina. At 18 GHz a 0.3 mm bond is around 0.2 nH, which is about 23 ohm of reactance, so the number of bonds in parallel and their length are both part of the match. The vendor's data is taken with a specific bond arrangement and a module that changes it moves the match.

For a first article the sensible route is to copy the vendor's evaluation carrier geometry exactly, measure it, and only then make changes. A module built from a redrawn carrier and measured against the datasheet will show a discrepancy that cannot be attributed without a reference.

Where a 10 W gallium nitride die is used

Test instrumentation, general communications and radar are the listed applications. In radar the attraction is the power per channel at X and Ku band, because a phased array's element count falls as the power per element rises, and the cost per element is dominated by the packaging rather than by the die.

In instrumentation the attraction is bandwidth and linearity together, since a driver that holds 39.5 dBm of intercept across 6 GHz to 18 GHz replaces two narrower amplifiers and the switch between them. That is a real saving in a signal generator, and it is where most of these die end up.

Two pages worth reading before a purchase order goes out are the amplifier cross reference and defense grade components; the first lists what else fits the socket, the second is the test sequence for a drop in, and one stop BOM sourcing covers the case where the shortage is already on the line.

Two questions buyers ask

Is the 35 percent efficiency consistent with 10 W out and 680 mA at 28 V? At saturation the arithmetic gives 52 percent drain efficiency. The 35 percent figure in the table belongs to a different operating point or band segment, and a thermal budget should be built from the dc input rather than from the efficiency column.

Can the die be attached with epoxy? The published data is taken with a eutectic attach to a 1.02 mm copper tungsten carrier. An epoxy attach changes the thermal path, and at 9 W of dissipation the junction temperature would have to be recalculated rather than assumed.