Contact Us

ADL7003

Brand: Analog Devices
Analog Devices ADL7003 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADL7003 — Analog & Mixed-Signal ICs | Superb Automation

ADL7003

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADL7003 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADL7003 at 50 GHz to 95 GHz: 0.36 W of DC on a 0.05 mm substrate

The ADL7003 is a gallium arsenide pHEMT balanced low noise amplifier covering 50 GHz to 95 GHz, supplied as die measuring 1.9 mm by 1.9 mm by 0.05 mm. In the lower band from 50 GHz to 70 GHz it gives 14 dB of gain, 21 dBm of output third order intercept and 12 dBm at one decibel compression; in the upper band from 70 GHz to 90 GHz the gain rises to 15 dB and the compression point to 14 dBm. It draws 120 mA from 3 V, and the input and output are matched to 50 ohm on chip. Every figure was taken with a single 0.076 mm ribbon bond of minimal length.

Published values

ParameterValue
Frequency range50 GHz to 95 GHz
Gain14 dB typical, 50 GHz to 70 GHz; 15 dB typical, 70 GHz to 90 GHz
Noise figure5 dB typical
Output power at 1 dB compression12 dBm typical lower band, 14 dBm typical upper band
Saturated output power18 dBm typical
Output third order intercept21 dBm typical
Input return loss15 dB typical
Output return loss20 dB typical
Supply3 V at 120 mA
Die size1.9 mm by 1.9 mm by 0.05 mm
Assemblysingle 0.076 mm ribbon bond, minimal length

0.36 W of DC and almost all of it becomes heat

3 V at 120 mA is 0.36 W. At the 14 dBm compression point the output is 25 mW, so 0.335 W is dissipated on a die face of 3.61 square millimetres, which is 0.093 W per square millimetre. That is a modest number next to a power amplifier, and it is still the figure that decides how the die is mounted, because 0.05 mm of gallium arsenide has almost no lateral spreading.

A 50 micrometre substrate is thin enough that the wafer is handled on a carrier and thin enough that the die has to be treated as fragile through every step after singulation. It is also thin enough that the backside ground is close to the active layer, which is what makes 95 GHz possible at all. The practical consequence is that the die attach thickness becomes a controlled parameter: a 25 micrometre bond line against a 10 micrometre one shifts the ground reference and shows up as a change in the match at the top of the band.

One ribbon bond is the whole transition

At 90 GHz the free space wavelength is 3.3 mm and the wavelength on the board is closer to 1.5 mm, so a 0.1 mm ribbon is a measurable fraction of a wavelength. The data sheet specifies a 0.076 mm wide ribbon of minimal length for that reason. The ribbon is inductive, the inductance is proportional to length, and the on chip match was characterised with the short one.

This is also where a second source claim usually fails. Two amplifiers can agree on gain, noise figure and compression point and still not be interchangeable, because the pad geometry sets the usable ribbon length and the ribbon is the matching element at these frequencies. A substitution study at W band that only compares the table is not a substitution study.

Two band tables, and why the upper band is the friendlier one

The lower band from 50 GHz to 70 GHz is the harder of the two: 14 dB of gain against 15 dB above 70 GHz, and 12 dBm of compression against 14 dBm. That is the opposite of what a cascade budget usually assumes, because the band where the part is quietest in terms of added noise is not the band where it is strongest.

Noise figure is 5 dB typical across the range, so the first stage sets the system figure almost completely. A second ADL7003 behind the first, with 14 dB of gain ahead of it, contributes 5 dB plus ten times the log of the ratio in the Friis form, which works out to about 0.11 dB of added noise. The first stage is worth paying for; the second one is worth whatever the gain budget needs and not much more.

Where a customer needs a second position on this part, the RF component sourcing page is the starting point, the LNA selection guide sets out the checks a substitution has to pass, and one stop RF supply is the short lead time route we quote against.

Two questions buyers ask

Can the ADL7003 be bonded with wire instead of ribbon? The published figures are taken with a single 0.076 mm ribbon of minimal length. A round wire of the same length has higher inductance, which shifts the input match and changes the gain at the top of the band, so the figures no longer apply unchanged.

What supply current should be budgeted? 120 mA from 3 V, which is 0.36 W. That is also very nearly the whole dissipation, since the radio frequency output at the compression point is 25 mW.