Contact Us

HMC637ALP5

Brand: Analog Devices
Analog Devices HMC637ALP5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC637ALP5 — Analog & Mixed-Signal ICs | Superb Automation

HMC637ALP5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC637ALP5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC637ALP5: 0.1 GHz to 6 GHz, 29 dBm, and 25 square millimetres of leadframe

The HMC637ALP5 is the packaged form of the 0.1 GHz to 6 GHz pHEMT distributed power amplifier: 13 dB of gain, 29 dBm at one decibel compression, 44 dBm of output third order intercept and 400 mA from 12 V, in a 32-lead, 5 mm by 5 mm leadframe chip scale package that is compatible with high volume surface mount assembly. The package carries the bypass capacitors on the pins, which is what makes it usable on a laminate, and it puts 4 W of heat into a 25 square millimetre footprint through a single exposed pad.

Published values

ParameterValue
Frequency range0.1 GHz to 6 GHz
Gain13 dB
Gain flatness0.75 dB from 100 MHz to 6 GHz
Output power at 1 dB compression29 dBm
Output third order intercept44 dBm
Supply12 V at 400 mA
Package32-lead, 5 mm by 5 mm LFCSP, 25 square millimetres
Gate pinsVGG1 and VGG2
Bypass pinsACG1 to ACG4
Unused pins14 pins marked no internal connection
Matching50 ohm input and output, no external matching components

Four watts through one exposed pad

12 V at 400 mA is 4.8 W of DC against 0.79 W of output at compression, which leaves 4.0 W to leave through the exposed pad. The pad is the only thermal path, and the via field under it is not a detail: at 4 W a thermal resistance from pad to board of 8 degrees per watt is a 32 degree rise, and a via field that reaches only half the pad area doubles that.

The board also has to spread what arrives. Twenty-five square millimetres of package footprint is not enough copper to dump 4 W into still air, so the far side of the board needs a plane, and the number of thermal vias should be counted against the current the pad has to pass rather than against a generic recommendation. A 12 V rail drawing 400 mA through a thin pour adds its own drop, which the part will interpret as a lower drain voltage.

The pins marked no internal connection are not ground

Fourteen of the 32 pins are marked as having no internal connection. They are there for mechanical reasons and for the leadframe, and they should be soldered to the pad pattern but not connected to any net that carries current. Connecting them to a signal or to a supply rail is a common way to turn a quiet amplifier into one that oscillates at a frequency nobody was looking at.

The pins that do matter are laid out with the two gate pins and the four bypass pins around the die. Each bypass pin needs its own capacitor at the package edge, with the shortest possible return to the ground pins, because the loop area is what sets the impedance at the frequencies where the distributed stage has gain but no directional isolation.

Where the package helps the schedule and where it charges for it

Surface mount assembly means no die attach, no wire bonding and no visual inspection of bonds, which for a low volume build is the difference between a process someone has to own and a reflow profile the assembler already runs. That is the reason this order code exists next to the die.

The package charges for it in two places. The transition at each port costs a few tenths of a decibel at the top of the band, and the thermal path gains two interfaces between die and board. Neither is a reason to avoid the part; both are reasons to characterise the packaged board rather than to carry over numbers measured on a carrier.

When an order code in this family cannot be found, the RF component sourcing page lists what else does the same job, how to verify a drop in replacement covers what to check before a part is dropped into an existing board, and component lead time solutions is the route we take on a live shortage.

Two questions buyers ask

Can the unused pins be tied to ground? They should be soldered for mechanical reasons and left unconnected electrically. Tying them to ground or to a rail changes the parasitic network around the die and can produce an oscillation that the data sheet does not describe.

Does the package need external matching at 100 MHz? No. The input and output are matched to 50 ohm across the published range and no external matching components are required. What is required is a proper bypass at each of the four access pins.