Contact Us

CC1175RHBR

Brand: Texas Instruments
Texas Instruments CC1175RHBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC1175RHBR — Power Management & Signal Chain | Superb Automation

CC1175RHBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC1175RHBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC1175RHBR narrowband RF transmitter in the 32 pin 5 by 5 mm VQFN body

The CC1175RHBR is a single chip transmitter for narrowband systems, with no receiver in the package. It covers the 164 to 192 MHz, 274 to 320 MHz, 410 to 480 MHz and 820 to 960 MHz bands, delivers up to +16 dBm with a 0.4 dB step size, and holds a phase noise figure of minus 111 dBc per hertz at 10 kHz offset. The part exists for one way links: metering, alarm, telemetry and smart grid nodes that transmit and never listen.

Removing the receiver is what allows the transmitter to be good at the job it does. All the current and all the silicon area go into the power amplifier, the synthesiser and the modulator, so the phase noise and the spectral efficiency are better than a transceiver at the same price. The narrowband requirement is the reason this matters: a 9.6 kbps signal inside a 12.5 kHz channel, which is what the FCC narrowbanding mandate asks for in the United States, needs a clean synthesiser and a modulator that does not smear energy into the adjacent channel. A generic transceiver usually meets the limit with margin only at lower data rates.

Key parameters taken from the CC1175RHBR document

FunctionSingle chip transmitter, no receiver, with integrated filters that remove the need for external SAW and IF filters
Frequency bands164 to 192 MHz, 274 to 320 MHz, 410 to 480 MHz and 820 to 960 MHz
Output powerUp to +16 dBm, programmable in 0.4 dB steps, with automatic output power ramping
Phase noiseMinus 111 dBc per hertz at 10 kHz offset
Spectral efficiency9.6 kbps inside a 12.5 kHz channel, in compliance with the FCC narrowbanding mandate
Data rate0 to 200 kbps, with a 128 byte transmit FIFO
Modulation2-FSK, 2-GFSK, 4-FSK, 4-GFSK, MSK and OOK
Current45 mA in transmit at +14 dBm, 0.12 microamps in power down and 0.5 microamps with the timer running
Supply2.0 to 3.6 V, all supply pins at the same potential
TemperatureMinus 40 to plus 85 C ambient
ClockCrystal oscillator with TCXO support and control, including in the power modes
Range extensionIntegrates with the CC1190 front end for up to +27 dBm output
BodyVQFN 32 pins, 5 by 5 mm, with a junction to ambient thermal resistance of 31.3 C per watt
Order code factsCC1175RHBR, VQFN RHB 32 pins, 3000 pieces on a large reel, NIPDAU or NIPDAUAG finish, moisture level 3 with a 168 hour floor life, marking CC1175; the T suffix is the 250 piece small reel

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The 45 mA at plus 14 dBm is a transmit only figure, and on a one way node it is the whole power budget. A metering transmitter that sends a burst once every fifteen minutes spends almost all of its life in power down at 0.12 microamps, and the average current is set by the burst length and the interval rather than by the peak. That is why this part can run for a decade from a lithium thionyl chloride cell: the peak current is high, the cell has to be able to deliver it, and the average is negligible. The cell choice and the bulk capacitor across the supply are what decide whether the burst pulls the rail down far enough to reset the part.

Phase noise at 10 kHz offset is the number that decides whether the adjacent channel limit is met. In a 12.5 kHz channel at 9.6 kbps, the modulation sits close to the carrier, and a synthesiser with poor close in noise spreads energy into the neighbouring channel where the regulator measures it. The minus 111 dBc per hertz figure is what allows the part to claim the narrowbanding compliance without an external filter, which is the cost argument for the whole device: no SAW filter, no IF filter, no extra matching.

The frequency resolution is coarse in the low bands and fine in the high band, which is a consequence of the synthesiser architecture rather than a limitation of the firmware. In the 820 to 960 MHz band the resolution is 200 Hz, in the 410 to 480 MHz band 100 Hz, and in the 164 to 192 MHz band 6 hertz. A channel plan with 12.5 kHz spacing is comfortable in every band. A plan with very fine steps at 868 MHz is not, and the difference has to be found in the synthesiser tables rather than assumed from the high band figure.

The TCXO support is worth planning for on any product that has to hold frequency over a wide temperature range. A plain crystal pulls with temperature, and a narrowband channel plan has little room for that pull. The part can drive and control a TCXO, including in the power modes, which keeps the reference stable while the rest of the device sleeps. The cost is one more component and a little more current while the reference is warming, and it is usually cheaper than a channel plan with wider spacing.

  • Delivered output power at the antenna connector with the ramping profile the firmware uses, not the register setting.
  • Adjacent channel power at the channel spacing the regulator measures, on the final matching network.
  • Frequency accuracy over the full temperature range, with the chosen reference source.
  • Supply droop during the transmit burst, measured at the package pins with the production cell and the production bulk capacitor.
  • Harmonic levels at the second and third harmonic, since a one way transmitter is often the only radio on the board and the harmonics still have to meet the limit.
  • Power down current on the assembled board, because a leaking level shifter on the SPI bus hides the sub microamp figure.

Which projects this part fits

This part fits wireless metering and advanced metering infrastructure, one way alarm and security transmitters, smart grid telemetry, industrial monitoring nodes that report to a concentrator, wireless sensor networks with a star topology, and IEEE 802.15.4g systems in the sub 1 GHz bands. It also fits products that must meet FCC Part 90 or the European narrowband requirements at 9.6 kbps in 12.5 kHz. Customers building a two way product use the transceiver member of the same family instead, and customers who need longer range pair this transmitter with the front end device to reach +27 dBm.

Questions that come up before a purchase order is released

Why use a transmitter instead of a transceiver?

Because the product never listens. A metering node, an alarm sensor or a telemetry transmitter sends a short burst and sleeps, and a receiver would add current, board area and cost for a function that is never used. The transmitter also spends all its silicon on the output stage, so the delivered power and the spectral quality are better than a transceiver at the same price point.

Can the part be used at 169 MHz for European metering?

Yes, the 164 to 192 MHz band is covered, with the highest frequency resolution of the device. The channel plan and the duty cycle are set by the regional regulation rather than by the part, and the reference source has to hold the channel over temperature because the band is narrow. Customers in that band normally use a TCXO rather than a plain crystal.

What does the 0.4 dB output step buy?

It allows the transmitted power to be set to the regulatory limit rather than to a convenient register value. In a band where the limit is tight, a 1 dB step can leave half a decibel on the table, and on a product that ramps its output for battery reasons the finer step gives a smoother profile. The step is also used during the automatic ramping at the start of a burst, which keeps the spectrum clean at the leading edge.

Does the part need an external power amplifier?

Only for range beyond the +16 dBm it delivers. With the front end device the output reaches +27 dBm, which is a different product class and brings its own regulatory and thermal questions. For a node that reports to a concentrator a few hundred metres away, the on chip amplifier plus a good antenna is enough, and it avoids the current and the heat of an external stage.

How is the part checked at incoming inspection?

Reel and moisture bag check, marking check, and a functional transmit test on a known good board measured at the antenna connector with a spectrum analyser or a power meter. Frequency accuracy and output power are the two figures that show a bad lot quickly. Because the part is a transmitter only, the test does not need a receiver, which makes the fixture simpler than for a transceiver.

How SUPERB handles this line

We supply the CC1175RHBR from original reels with lot and date code traceability, and we hold the reel size on the order because the large reel and the small reel carry the same body. The RF component sourcing page lists the sub 1 GHz transmitter and front end families we carry, obsolete RF part replacement covers the case where a transmitter in a deployed product is discontinued, and RF power transistor cross reference is the page to start from when a link needs more delivered power than one package can give.