Contact Us

BQ294502DRVR

Brand: Texas Instruments
Texas Instruments BQ294502DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ294502DRVR — Power Management & Signal Chain | Superb Automation

BQ294502DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ294502DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ294502DRVR second level overvoltage protector for two and three cell packs

The BQ294502DRVR is a fixed threshold, fixed delay overvoltage monitor for two and three series lithium packs. Each cell is compared against 4.35 V, and if any cell stays above that level for 4 seconds the output goes high. It draws about 1 uA from the pack, leaks less than 100 nA per cell input, and comes in a 6 pin SON measuring 2.00 mm by 2.00 mm, which is small enough to fit on the strip beside the cell tabs.

This is a second level device. The primary protector or the gauge handles normal overvoltage, overcurrent and short circuit; this part exists for the case where the primary layer does not act. Because the threshold and the delay are fixed in silicon, there is nothing to misconfigure in the field, and there is nothing for a service technician to reset. The family covers 3.85 V to 4.6 V across its order codes, all with plus or minus 10 mV of accuracy.

Key parameters taken from the BQ294502DRVR document

Cells covered2 or 3 in series
Overvoltage threshold on this order code4.35 V fixed, plus or minus 10 mV
Output delay on this order code4 s fixed
Other delay option in the family6.5 s
Threshold range across the family3.850 V to 4.600 V in fixed steps
Supply currentabout 1 uA with all cells below the protect threshold
Leakage per cell inputbelow 100 nA
PackageDRV, 6 pin SON, 2.00 mm by 2.00 mm
VDD operating range3 V to 25 V
VDD absolute maximum30 V
Cell input absolute maximum30 V per input, and 5 V between adjacent inputs
Operating ambientminus 40 C to 110 C

The table above is read from the vendor document rather than from a catalogue summary. Where the document prints a minimum and a maximum, both are kept, because the number a test station should use is the limit and not the typical.

Where the numbers matter in a real build

The 4.35 V threshold on this code suits a 4.2 V cell with 150 mV of headroom, or a 4.35 V cell with none. That is a decision the pack maker has to make deliberately: on a 4.35 V cell this part sits exactly at the charge voltage, so any overshoot on the charge loop trips it. Most packs using this code are built around 4.2 V cells where the primary charger stops at 4.2 V and this device is a genuine backstop.

The adjacent input limit is 5 V, which is the specification that catches wiring mistakes. On a three cell pack the taps are within one cell of each other in normal operation, but during a cell disconnect or a blown tap resistor the difference can exceed 5 V and the input is damaged. The series resistor on each tap is what limits that current, and it is not optional.

Four seconds is long for a protection delay and that is the point. A pack that trips on a load dump is a warranty claim; a pack that trips after four seconds of sustained overvoltage is a pack that was being overcharged. The 6.5 second variant exists for packs where the charge profile has a longer absorption phase and a faster trip would be a nuisance.

The output is a level, not a latched state. Once the cell falls back below the threshold the output returns, so the pack controller has to latch the event itself if the record matters. For packs with a fuse driver, the output is usually wired to blow the fuse, which makes the trip permanent in hardware rather than in software.

  • Two micrometre class accuracy keeps the second level close to the cell limit without false trips on a healthy pack.
  • The 2 mm by 2 mm body fits on the cell tab strip, which keeps the sense wires short and the measurement honest.
  • Supply and leakage currents are low enough that a stored pack is not drained by its own protector.
  • No programming pins means no field reconfiguration risk and no configuration image to control.

Which projects this part fits

Tablet and notebook packs, power tool packs, portable instruments and any two or three cell pack that ships with a charger able to fail high. It is also common in packs that are serviced in the field, where a fixed threshold is easier to audit than a programmable one. The power management cross reference lists the protectors we hold, and the medical device component page covers the documentation that goes with safety relevant parts.

Threshold variants in the family and the first article list

The suffix after BQ2945 carries the threshold and the delay, and the document lists eleven variants between 4.225 V and 4.55 V. The table below sets out the ones that appear most often in packs built around 4.2 V and 4.35 V cells, with this order code marked.

Order codeThresholdDelay
BQ2945824.225 V4 s
BQ2945924.300 V4 s
BQ294502, this part4.350 V4 s
BQ2945044.350 V6.5 s
BQ2945064.380 V4 s
BQ2945124.400 V4 s
BQ294522 and BQ2945244.450 V4 s and 6.5 s
BQ294532 and BQ2945334.500 V4 s and 6.5 s
BQ2945344.550 V4 s

Six variants share a body, a pinout and a tape size, so the only thing that separates them on a shelf is the marking and the reel label. That is why the incoming check for this line reads the label against the purchase order and why we do not accept a substitute threshold without a written approval from the pack owner.

The output type is chosen with the receiving circuit, not on its own. A CMOS active high output idles low and drives a FET or a fuse driver directly; an open drain active low output needs a pull up and inverts the logic. Both appear in the same 6 pin body, so a reel that was bought by family name can put the opposite polarity on a board that worked in prototype.

The first article test ramps one cell above the threshold with the others held at nominal, records the trip point against a bench meter, and times the delay. Because the output is a level rather than a latch, the test also confirms that the receiving circuit latches the event; a pack that only records the output state loses the record when the cell cools and the output returns.

Questions that come up before a purchase order is released

Is 4 seconds too slow to protect a cell?

It is slower than the primary protection, which is the intent. A cell that is genuinely being overcharged stays above the threshold for minutes, so 4 seconds still acts long before damage. Short events are handled by the primary protector and do not need this device.

Can two of these share one pack?

Yes, they are independent monitors with no bus, so a pack can carry two devices watching different cell groups. The outputs are usually wired together to the same fuse driver, which means either device can act.

What is the difference between this and the BQ7718 family?

Both are fixed threshold second level monitors. This family covers two and three series cells with a 6 pin 2 mm body, while the BQ7718 covers two to five series cells in an 8 pin body with more threshold and delay options. Packs above three series cells need the 8 pin part, and the two are not footprint compatible.

How SUPERB handles this line

We supply the BQ294502DRVR with the threshold variant named in full on the order, and each reel is checked before kitting because a 4.35 V part and a 4.25 V part look identical on the tape. If a pack is short of one variant, we will say so rather than ship the nearest threshold. The date code management page covers how we track shelf life on protectors held for service spares.