LT3042MPMSE#TRPBF
Product Specifications
LT3042MPMSE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3042MPMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT3042MPMSE#TRPBF: the widest temperature code on the 200 mA regulator, in the leaded MSOP
What this order code is
LT3042MPMSE#TRPBF is the 200 mA LT3042 in the 10-lead MSOP with exposed pad, MP temperature code, tape and reel. The electrical table is the family table: 0.8 uV RMS of noise from 10 Hz to 100 kHz, 2 nV per root hertz at 10 kHz, 79 dB of supply rejection at 1 MHz, 350 mV of dropout at 200 mA, 1.8 V to 20 V input, 0 V to 15 V output, 100 uA SET current of plus or minus 1 percent, 2 mA of quiescent current, a 4.7 uF minimum ceramic output capacitor and reverse battery and reverse current protection.
This is the code for the case where the temperature code and the package both come from a qualification document rather than from convenience: MP is the widest letter in the ordering table, and MSE is the leaded body that can be probed and reworked when a board is built in small numbers or repaired in the field. The combination is rare in consumer work and normal in instrumentation that has to be serviceable at temperature.
Parameters as published
| Item | Value |
|---|---|
| Output current | 200 mA |
| Input voltage range | 1.8 V to 20 V |
| Output voltage range | 0 V to 15 V, set by one resistor |
| Dropout at 200 mA | 350 mV typical, 1.75 ohm |
| RMS noise, 10 Hz to 100 kHz | 0.8 uV |
| Supply rejection at 1 MHz | 79 dB |
| SET pin current | 100 uA, plus or minus 1 percent |
| Quiescent current | 2 mA, below 1 uA in shutdown |
| Minimum output capacitor | 4.7 uF ceramic |
| Temperature code | MP, limits in the ordering table |
| Body | 10-lead MSOP with exposed pad |
| Packing | tape and reel |
Numbers that decide the application
350 mV at 200 mA is 1.75 ohm, so the input floor is 3.65 V for 3.3 V out. Dissipation is 0.34 W from 5 V to 3.3 V, 0.30 W from 3.3 V to 1.8 V and 1.74 W from 12 V to 3.3 V, and in an MSOP the exposed pad is the only heat path, so the copper under it is part of the guarantee. At the cold end of an extended range the thermal resistance is better rather than worse, but the input capacitors and the SET network are the parts that move: a class 2 ceramic loses a fifth to a third of its capacitance at the cold extreme, and a thick film resistor with a 100 ppm per degree C coefficient moves the output by 0.33 percent over a 33 degree swing, which is 11 mV on 3.3 V.
The noise and rejection figures belong to the die: 0.8 uV is 0.0105 of a 16 bit code at 5 V and 2.7 codes at 24 bits, while 79 dB at 1 MHz turns 1 V of ripple into 112 uV and 100 mV into 12.6 uV. What changes at the extremes is not the rejection at 1 MHz but the low frequency behaviour of the SET capacitor, which is an electrolytic or ceramic part whose value and leakage move with temperature, and the low frequency noise that the SET filter exists to remove rises when that capacitor loses value.
The transient is set by the 4.7 uF minimum: 200 mA for 1 us is 42.6 mV and for 10 us it is 425 mV, so the capacitor is the transient specification and it has to hold its value over the whole temperature range the MP code is bought for. Quiescent current of 2 mA is 17.5 Ah a year, and in a cold soak the part draws the same, so a battery product that sits at minus 40 C for a season still spends that current unless the enable pin is used, since shutdown is below 1 uA.
Where it fits and where it does not
It fits a field serviceable instrument with a wide temperature requirement, a defence or aerospace module with a rework requirement, a cold climate outdoor installation and any line where the qualification document names both a temperature code and a leaded body. It does not fit a load above 200 mA in one body, a wide input drop without thermal copper, a board whose assembly process cannot solder an exposed pad, or an automotive line without confirming the qualification attribute for this exact code.
Supply and second source questions
The question that decides a substitute on this line is whether the alternative carries both attributes, the temperature code and the body, because each alone is easy to find and the pair is not. A part with the same footprint and the same noise but an industrial code fails the first cold test, and a part with the wide code in a DFN fails the rework requirement. The regulators and their codes are compared on the power management cross reference page.
Sourcing notes and next step
We confirm both the temperature code and the body on every line, and we will hold a line rather than ship the nearest match. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider regulator list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty