LT3060IDC-3.3#TRPBF
Product Specifications
LT3060IDC-3.3#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3060IDC-3.3#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3060IDC-3.3#TRPBF: 3.3 V industrial regulator in the 2 mm DFN with the guaranteed specifications
The LT3060IDC-3.3#TRPBF is the 3.3 V fixed LT3060 in the 8-lead 2 mm by 2 mm DFN, tape and reel, I grade, with part marking LFVY. It is the body to choose when the load regulation and dropout numbers have to be warranted, because those two specifications are guaranteed for the DFN and only typical for the ThinSOT. Input range is 1.6 V to 45 V, output current is 100 mA, quiescent current is 40 uA, and the 3.3 V output is held between 3.234 V and 3.366 V over line, load and temperature. The exposed pad is pin 9 and it is ground, not output, and it has to be soldered to the board.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.6 V to 45 V, 50 V absolute maximum |
| Output voltage | 3.3 V fixed, 3.234 V to 3.366 V over temperature |
| Line regulation | 1.3 mV typical, 7 mV maximum, guaranteed in this body |
| Load regulation | 3.1 mV typical, 24 mV maximum, 1 mA to 100 mA, guaranteed |
| Dropout voltage | 300 mV typical at 100 mA, guaranteed in this body |
| Quiescent current | 40 uA typical at no load |
| Output noise | 30 uV RMS with 10 nF on REF/BYP |
| Package | 8-lead 2 mm by 2 mm by 0.75 mm DFN, part marking LFVY |
| Exposed pad | Pin 9, ground, must be soldered |
| Thermal resistance | 48 C/W at 2500 square millimetres of copper, 60 C/W at 50, 20 C/W to case |
| Maximum junction | 125 C, thermal shutdown at about 165 C |
| Grade | I, minus 40 C to 125 C |
The two specifications the DFN buys
This is the code in the family where the electrical table has no caveat attached. Dropout is guaranteed for the DFN body, and load regulation is guaranteed for the fixed voltage options in the DFN body. On the ThinSOT codes the same two specifications are marked as not guaranteed at high output current, or not guaranteed at all for the fixed options, because of production test limitations, with those parts tested the same way as the adjustable version with ADJ tied to OUT. A buyer comparing prices between the DFN and the ThinSOT is comparing two different warranties on two of the six numbers that usually matter, and that difference is worth stating in a qualification report rather than discovering when a second source is proposed.
Copper under the pad decides the thermal limit
The vendor publishes 48 C/W at 2500 square millimetres of topside copper, 49 at 1000, 50 at 225, 54 at 100 and 60 at 50, measured on a four layer board with 1 oz internal planes, 2 oz outer copper and no thermal vias. The same worked example in the datasheet uses a 12.6 V input, a 2.5 V output and 50 mA, which is 0.513 W, a 27.8 C rise at 54 C/W and a 112.8 C junction from an 85 C ambient. Swapping in a 24 V input at the same 50 mA gives 1.04 W, which at 48 C/W is a 50 C rise and a 135 C junction, over the limit. The board area behind the part is therefore a real input to the thermal budget on a 24 V bus, and a 50 square millimetre pad will not carry it.
Why the pad is the ground node
The pad carries the return for the reference and the error amplifier as well as the heat. A thermal relief pattern of the kind that helps hand soldering adds thermal resistance exactly where the part is trying to shed heat, and a noisy ground under the pad shows up as output noise on a part whose whole selling point is 30 uV RMS. A solid connection to a ground plane with a via array is the arrangement the datasheet's thermal numbers assume. The DFN is also the only body in this family that carries automotive qualified variants, marked with a W in the order code, which is a separate product line rather than a grade option.
Buying the DFN code
The DFN 3.3 V code exists in E and I grades, and the same 2 mm body appears in the rest of the fixed voltage range, so a family can standardise on one footprint across 1.2 V to 15 V. That matrix, together with the grades that exist in each body, is on the power management cross reference. A line that has gone short can be recovered without a footprint change on BOM shortage recovery, and the split between a true drop in and a footprint change is set out on pin to pin cross reference.