Contact Us

LT3045IMSE#WTRPBF

Brand: Analog Devices
Analog Devices LT3045IMSE#WTRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3045IMSE#WTRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3045IMSE#WTRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3045IMSE#WTRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT3045IMSE#WTRPBF: the W suffix 500 mA regulator in the 12-lead MSOP and what the suffix actually states

What this order code is

LT3045IMSE#WTRPBF is the LT3045 in the 12-lead MSOP with exposed pad, I temperature grade, tape and reel, carrying a W suffix between the body code and the packing code. The electrical family is the one described on the product page: 500 mA at a typical 260 mV dropout from 1.8 V to 20 V, 0.8 uV RMS of noise over 10 Hz to 100 kHz, 76 dB of rejection at 1 MHz, a 100 uA SET current with plus or minus 1 percent initial accuracy, an output range of 0 V to 15 V and a 10 uF minimum ceramic output capacitor.

The W is the part of this order code that has to be handled carefully. The family page does not define it in the features or the description, so the honest reading is that W is an ordering level attribute recorded in the ordering information and the change notices for that body, not a change to the electrical behaviour described on the summary page. A line that relies on W for a specific qualification has to quote the notice number, because the summary page will not answer the question.

Parameters as published

ItemValue
Output current500 mA
Input voltage range1.8 V to 20 V
Output voltage range0 V to 15 V, set by one resistor
SET pin current100 uA, plus or minus 1 percent
Dropout at 500 mA260 mV typical
RMS noise, 10 Hz to 100 kHz0.8 uV
Spot noise at 10 kHz2 nV per root hertz
Rejection at 1 MHz76 dB
Minimum output capacitor10 uF, ceramic
Parallel operationsupported, outputs tied through ballast resistors
Body12-lead MSOP with exposed pad
Suffix Wordering level attribute, not defined on the family summary page
Packingtape and reel

Numbers that decide the application

Paralleling is the capability that makes this code interesting beyond a single 500 mA rail. Two devices share the load through small ballast resistors, with their SET pins tied so both regulate to the same voltage, and each contributes noise that is uncorrelated, so the combined noise falls by about 1.41 while the current doubles. Four parts give 2 A and half the noise of one, at four times the board area and four times the 2.2 mA of quiescent current, which is 76.9 Ah a year and a mains-powered proposition only.

The load sharing depends on the ballast resistors, not on the regulators. A 10 milliohm ballast at 250 mA drops 2.5 mV, which is small compared with the SET tolerance but large enough to bias the sharing in the right direction, and the resistors have to be matched because a mismatch becomes a current mismatch. With 0.52 ohm of pass element per device, a 10 mV difference between two channels moves about 1 percent of the load, so the sharing is good and the thermal coupling between the two bodies is what actually limits the pair.

The single device numbers are unchanged: 5 V to 3.3 V at 500 mA is 850 mW in a 3 mm MSOP pad, and 0.8 uV RMS is 0.0105 of a 16 bit code at 5 V. The 10 uF output capacitor gives 500 mV for a 10 us, 500 mA step, so a load that steps at that rate needs more capacitance or a lower inductance path from the capacitor to the load. The SET resistor is 33 kohm for 3.3 V, 50 kohm for 5 V and 150 kohm for 15 V, and its tolerance sits directly on the rail.

Where it fits and where it does not

It fits a low noise rail that needs more than 500 mA, a synthesizer or converter supply built from two or four paralleled devices, an instrument where the noise floor is the specification, and a line that has already qualified the MSOP body. It does not fit a battery product, a 12 V input, a setpoint above 15 V, or a programme that cannot document what W means in its own qualification file.

Supply and second source questions

This is the code where the suffix question has to be answered before the quote, not after: ask what W covers in the qualification file, and expect the answer to come from the ordering information rather than the family page. The second question is the ballast network, which is not part of the part number and is the first thing lost when a build is copied. Low noise regulators and their parallel behaviour are compared on the power management cross reference page.

Sourcing notes and next step

We quote body, letter, suffix and packing separately and will say plainly that the family page does not define W, so the limits come from the ordering information for the code on the reel. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider regulator list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty