Contact Us

LT3060HTS8#TRPBF

Brand: Analog Devices
Analog Devices LT3060HTS8#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3060HTS8#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3060HTS8#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3060HTS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3060HTS8#TRPBF: adjustable 45 V input regulator tested to 150 C

The LT3060HTS8#TRPBF is the adjustable LT3060 in the 8-lead ThinSOT, tape and reel, H grade, guaranteed from minus 40 C to 150 C at the junction. The 600 mV reference and an external divider set any output up to 44.5 V, the input range is 1.6 V to 45 V, and the part carries 100 mA with 40 uA of quiescent current. In a hot enclosure it is the code that lets a non standard output voltage keep the same temperature claim as the fixed codes, which is why it turns up on rails such as 4.2 V, 6 V or 12 V in sealed equipment.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 50 V absolute maximum
Reference voltage600 mV, 585 mV to 612 mV over temperature, H and MP grades
Output range600 mV to 44.5 V
Output current100 mA, current limit with foldback
Line regulation0.6 mV typical, 4 mV maximum, H grade
Load regulation0.2 mV typical, 9 mV maximum, H grade
ADJ pin bias current15 nA typical, 60 nA maximum, out of the pin
Quiescent current40 uA typical, below 1 uA in shutdown
Package8-lead ThinSOT, part marking LTDTF
Thermal resistance57 C/W to 67 C/W junction to ambient, 25 C/W to case
Maximum junction150 C, thermal shutdown at about 165 C
GradeH, minus 40 C to 150 C

The reference drift and the divider

The reference is specified over the whole 150 C window at 585 mV to 612 mV, a 4.5 percent spread that is wider than the 25 C figure and wider than the I grade. Because the output is the reference multiplied by the divider ratio, that spread scales with the output: a 600 mV output moves by 27 mV and a 12 V output moves by 540 mV. That is the arithmetic that decides whether an adjustable output at high temperature needs a trim, and it is also the reason the fixed codes exist, since their internal divider is trimmed on the die. The ADJ pin bias current of 15 nA typical flows out of the pin and adds to the bottom resistor current, so the divider has to stay near 10 uA for the error to remain a few millivolts.

Hot start behaviour

The REF/BYP capacitor does double duty: it sets the noise floor at 30 uV RMS with 10 nF, and it sets the soft start ramp. In shutdown it is discharged, so the ramp is the same on every enable. That matters in equipment that cycles power in a hot enclosure, because a capacitor that has been sitting at 120 C has a different value from one at room temperature and the ramp would otherwise vary with the thermal history. The internal protection is current limit with foldback on input to output differential, plus thermal shutdown at about 165 C, plus reverse input, reverse output and reverse output to input protection, so a hot board that sees a fault is protected on all three paths rather than on current alone.

Choosing between H and MP for the cold end

Both grades reach 150 C. The difference is the cold end: H is guaranteed from minus 40 C and MP from minus 55 C, and the MP part is tested over the full minus 55 C to 150 C window rather than tested at temperature. A 15 C difference at the bottom of the range is the entire distinction, and it is worth paying for only where the equipment is genuinely exposed to minus 40 C or below, such as an outdoor cabinet at altitude. Everywhere else the H code is the cheaper way to buy the 150 C hot end.

Where the adjustable H code fits

This code covers the odd output voltages at the high temperature end of the family, alongside the seven fixed options and the DFN body with its automotive variants. The temperature grades, bodies and markings are tabulated on the power management cross reference, the shortage route for a single line item is BOM shortage recovery, and the case for consolidating several ADI rails under one supplier is made on one stop BOM sourcing.