Contact Us

LT3045EDD-1#TRPBF

Brand: Analog Devices
Analog Devices LT3045EDD-1#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3045EDD-1#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3045EDD-1#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3045EDD-1#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT3045EDD-1#TRPBF: the 500 mA low noise regulator with the VIOC pin that moves heat upstream

What this order code is

LT3045EDD-1#TRPBF is the 500 mA member of the LT3045 ultra low noise regulator family in the 10-lead 3 mm by 3 mm DFN, E temperature grade, tape and reel. The architecture is a precision current reference followed by a voltage buffer, so output noise, supply rejection, bandwidth and load regulation stay nearly constant whatever output voltage the single SET resistor asks for. The family publishes 0.8 uV RMS from 10 Hz to 100 kHz, 2 nV per root hertz at 10 kHz, 76 dB of supply rejection at 1 MHz, a 260 mV dropout at 500 mA and an output range of 0 V to 15 V from a 1.8 V to 20 V input.

The -1 in the code is the part that changes the application. LT3045-1 carries the VIOC function, a pin that tells the upstream switching regulator how much headroom the linear stage needs, so the switcher output tracks the linear regulator's dropout instead of sitting at a fixed voltage. The plain LT3045 does not have that pin. On a 500 mA part dropping from a high rail, that difference decides whether the heat stays in the DFN or moves into the inductor of the converter in front of it.

Parameters as published

ItemValue
Output current500 mA
Input voltage range1.8 V to 20 V
Output voltage range0 V to 15 V, set by one resistor
Dropout at 500 mA260 mV typical
RMS noise, 10 Hz to 100 kHz0.8 uV
Spot noise at 10 kHz2 nV per root hertz
Supply rejection at 1 MHz76 dB
SET pin current100 uA, plus or minus 1 percent
Bandwidth1 MHz
Quiescent current2.2 mA, below 1 uA in shutdown
Minimum output capacitor10 uF ceramic
VIOC pinpresent on this -1 code, absent on the plain LT3045
Protectionreverse battery, reverse current, foldback current limit, thermal limit
Body10-lead 3 mm by 3 mm DFN
Grade and packingE, tape and reel

Numbers that decide the application

260 mV at 500 mA is 0.52 ohm, so the minimum input for a 3.3 V output is 3.56 V and for a 5 V output 5.26 V. The heat follows from the same 0.52 ohm when the input is high: 5 V to 3.3 V at 500 mA is 0.85 W, 12 V to 3.3 V is 4.35 W, and 20 V to 15 V is 2.5 W. A 3 mm DFN with an exposed pad can pass the first figure on a board with copper, cannot pass the second at all, and passes the third only with a thermal plane. That arithmetic, not the 500 mA rating, is why the -1 code exists: with VIOC the converter in front is asked for output plus dropout rather than a fixed 12 V, and the 4.35 W becomes 0.85 W.

The 100 uA SET current of plus or minus 1 percent means a 33 kohm resistor sets 3.3 V, and the resistor tolerance adds directly to the output, so one percent of 3.3 V is 33 mV before the reference error is counted. A 0.1 percent resistor is the normal choice on a precision rail, and the SET pin needs a capacitor to ground for noise, which is where the 0.8 uV figure assumes the recommended network.

0.8 uV RMS is 0.0105 of a 16 bit code at a 5 V full scale, 0.17 of a 20 bit code and 2.7 codes at 24 bits, so the regulator is not the accuracy limit until a converter is deeper than 20 bits. The rejection figure needs the same arithmetic: 76 dB at 1 MHz turns 1 V of ripple into 158 uV, and 100 mV into 16 uV, which is why this part is normally placed behind a switching supply rather than instead of one. Quiescent current of 2.2 mA is 0.44 percent of a 500 mA load and 220 percent of a 1 mA load, so a rail that sleeps at microamps has to use the shutdown pin, which takes the part below 1 uA.

Where it fits and where it does not

It fits a PLL, VCO, mixer or low noise amplifier rail, a 16 to 20 bit converter supply, a post regulator behind a switching converter, and any node where 0.8 uV and 76 dB at 1 MHz are the requirement. It fits the -1 code specifically where the upstream converter can be controlled, because that is the only case where VIOC is usable at all. It does not fit a load above 500 mA without paralleling, an input above 20 V, a board that cannot remove 0.85 W from a 3 mm body, or a rail whose output capacitor is below 10 uF, where the part is not guaranteed stable.

Supply and second source questions

The two questions that come with this code are the -1 suffix and the noise claim. A plain LT3045 does not have VIOC, and a board laid out for the -1 with the tracking function in use will not work with the plain part even though the footprint and the 500 mA rating match. On noise, vendors that quote 0.8 uV without the bandwidth, or without saying which output capacitor and which SET network were fitted, are quoting a number that may not be reproducible on a different board. Regulators with the same footprint and their published noise figures are compared on the power management cross reference page.

Sourcing notes and next step

We quote this code with the -1 confirmed, because that suffix is the whole reason for the line in most bills of materials. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider regulator and reference list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty