ADS1220IPWR
Product Specifications
ADS1220IPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ADS1220IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADS1220IPWR: 24-bit 2 kSPS delta-sigma converter with matched current sources
ADS1220IPWR is the 24-bit member of the same four-channel family, bought when the sensor needs the extra bits in a TSSOP body of 16 pins. The converter keeps the two differential or four single-ended inputs, the gain stage to 128, the 2.048 V reference and the two matched current sources of the 16-bit part and raises the resolution to 24 bits, quoted as up to 20 bits of effective resolution. Supply is 2.3 V to 5.5 V and the data rate runs to 2000 samples per second with single cycle settling.
Order code and package
| Order code | ADS1220IPWR |
| Function | 4-channel, 2 kSPS, 24-bit converter with gain stage and reference |
| Interface | SPI mode 1 |
| Inputs | two differential or four single-ended |
| Reference | internal 2.048 V, 5 ppm per C typical |
| Excitation | two matched sources, 10 microamps to 1.5 mA |
| Oscillator | internal, 2 percent accuracy |
| Package | TSSOP, 16 pins |
| Temperature range | minus 40 to plus 125 C |
| Supply | 2.3 to 5.5 V |
| Resolution | 24 bits, up to 20 bits effective |
| Datasheet | SBAS501 revision D |
Electrical parameters that decide the application
| Effective resolution | up to 20 bits, which is the number to compare against a 16-bit part |
| Data rate | up to 2000 samples per second, single cycle settling |
| Mains rejection | 50 Hz and 60 Hz together at 20 samples per second |
| Gain | 1 to 128 |
| Excitation floor | 10 microamps, lower than the 16-bit part, which matters for a small RTD |
| Supply current | 120 microamps in duty-cycle mode with the gain stage bypassed |
| Reference drift | 5 ppm per C typical, 512 microvolts over the 125 C span |
| Input range | supply span minus 0.4 V, divided by the gain, when the gain stage is on |
| Interface pins | CS, SCLK, DIN and DOUT with DRDY, so four wires plus a data ready line |
| Package | TSSOP 16, the same footprint as the 16-bit part |
Points to check before this part goes on a BOM
Twenty effective bits is the honest headline against a 16-bit neighbour, and it arrives at low data rates. At 2 kSPS the noise floor rises and most of that margin is gone, so the choice between this part and the 16-bit one is a choice about the rate the product actually runs at.
The excitation floor drops from 50 microamps to 10 microamps between the two parts. A 1 kohm RTD at 10 microamps moves only 10 mV per 100 C of the 0.385 ohm per C coefficient, which is 3.85 mV per C, so self heating falls with the square of the current: 1 uW against 25 uW at 50 microamps.
The matched sources are specified as a pair. Using one source for two channels loads it with two loops and breaks the match the two-wire cancellation depends on, even though the part will still convert.
The reference and the gain stage are on the same die, so the drift terms add rather than cancel unless the measurement is ratiometric. On a load cell excited from the reference output, both terms move together and the ratio stays flat.
Burnout detection and bias voltage for thermocouples are built in, which removes the pull-up resistors and the bias network that a discrete front end needed, but both draw current from the same input pins, so they stay off in a low-power duty-cycled product.
The 24-bit codes come out over SPI in twos complement, so the host has to sign extend into a 32-bit word before scaling; a 16-bit accumulator silently truncates the low byte.
Where this order code fits
Boards comparing the 16-bit and 24-bit members of this family usually decide on the data rate first and the bit count second. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Is this part a drop-in for the 16-bit version? Pin and register arrangement follow the same family, but the resolution, the excitation floor and the conversion timing differ, so the firmware settings have to be rechecked rather than copied.
What limits the effective resolution? The data rate and the gain. Twenty bits is a low-rate figure; at 2 kSPS the noise floor is higher and the usable resolution drops.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.