Contact Us
  • Home
  • COMPONENTS
  • Fluid Check Valves and Shuttle Valves for Reagent and Pneumatic Lines

Fluid Check Valves and Shuttle Valves for Reagent and Pneumatic Lines

A check valve in a reagent line is a pressure gate, and the figure that decides whether the line works is the cracking pressure, not the body size. The parts below cover diaphragm, umbrella, duckbill and spring check valves from 0.11 psi to 10 psi cracking, plus shuttle valves for choosing between two pneumatic sources. Cracking pressure is quoted with the spring tolerance, because a 3 psi nominal spring is allowed to open anywhere from 2.1 to 3.9 psi. Every entry lists body material, seal material, connection and maximum working pressure, so the valve is matched to the reagent before it is matched to the tube.
quote now

Product Specifications

Product Overview

A check valve fails in two directions. It can leak backwards, which is the failure everyone expects, or it can refuse to open, which is the failure that stops a run. The second one is more common on a reagent line, because the pressure available is small. A bottle standing 500 mm above the valve gives about 0.7 psi of head, and a valve with a 3 psi spring will never open on that head no matter how long the pump runs. The cracking pressure has to sit below the pressure the line can actually produce at the flow the method needs.

Cracking pressure is the forward differential at which the valve just begins to pass, and it is not the only number that matters. The reseal pressure is where it closes again, and on a diaphragm valve that is close to the cracking figure because the diaphragm is free floating and follows the slightest pressure change. On a spring valve the spring sets both, and the spring itself carries a tolerance. A 3 psi nominal spring with a 30 percent tolerance may open at 2.1 psi or at 3.9 psi, so a line that only makes 2.5 psi is a coin toss rather than a specification.

The seat and the diaphragm are what the reagent touches. A spring valve in natural nylon with Buna-N seals is the general purpose choice for water based reagents, and it is the wrong choice for a solvent or a strong base. Viton covers most solvents and acids, EPDM covers caustic and hot water, and silicone is chosen where the line is disposable and the seal has to meet a biocompatibility class. A valve whose body is fine and whose seal swells will leak at the seat, and the leak shows up as a slow drift in a reagent blank rather than as a puddle.

A shuttle valve is a different part doing a different job: two inlets, one outlet, and the higher of the two pressures wins. It is common on pneumatic lines where a manual push button and an automatic signal both have to drive the same cylinder, and it is rarely used on a liquid reagent line, because two check valves feeding a tee give the same result with smaller dead volume. The shuttle parts on this page are listed for air and inert gas duty, and their cracking figures are around 1 psi or less so that either input can take over without a pressure spike.

Key Specifications

ParameterValueNote
Valve typesdiaphragm, umbrella, duckbill and spring check valves, plus poppet shuttle valvesthe type decides the cracking range more than the body does
Cracking pressure0.11 psi on a Luer diaphragm valve, 0.25 psi on a barbed diaphragm valve, 0.5 psi on a molded diaphragm valve, 0.5 to 10 psi on spring valves0.11 psi is about 77 mm of water, 3 psi is about 2.1 m
Spring toleranceplus or minus 30 percent on the nominal cracking pressurea 3 psi spring may open between 2.1 and 3.9 psi
Reseal pressure1.9 psi on the molded diaphragm family, close to cracking on a free floating diaphragmreseal sets how much reverse flow slips past before the seat closes
Maximum working pressure50 psi on the molded diaphragm family, 25 or 50 psi on the barbed spring family, 250 psig back pressure on the duckbill bodythe barbed duckbill version is limited to 100 psig by the tube
Body materialsnatural nylon, polypropylene, PVDF, polycarbonate, polysulfone, ABS on the Luer familyPVDF for aggressive reagents, polypropylene for cost
Seal materialssilicone, EPDM, Viton, Buna-N, neoprene, and a silicone umbrella or diaphragmthe seal is the part the reagent attacks first
Connectionshose barbs from 1/32 to 3/4 inch, 1/8 MNPT, male and female Luer, 10-32 and 1/8 NPT on the shuttle familythe barb has to match the tube the method already uses
Luer standardISO 80369-7 on the Luer diaphragm familythe small bore standard for medical fluid paths
CleanlinessUSP Class VI, ISO 10993-1 and FDA 21 CFR 181.32 on the barbed diaphragm familywhat a disposable or a patient contact line is asked for
Mounting attitudeany position on the diaphragm family, because a free floating diaphragm has no spring to fighta spring valve adds its offset in every attitude
Shuttle crackingunder 1.0 psi on the 1/8 NPT shuttle family, about 1 psig on the poppet typeeither inlet can take over without a pressure spike
Shuttle pressure0 to 125 psi on the pneumatic shuttle family, 200 psi on the inline type, 300 psig on the poppet typeair and inert gas duty
Reverse leakageunder 0.06 standard cubic inches per minute at 1 psi on the umbrella familya leak figure, not a drop tight claim

Included Models and Order Codes

The table covers the four checking principles that turn up on analyser and instrument lines. Diaphragm valves are the low pressure end, from 0.11 psi at a Luer port to 0.5 psi on a molded barbed body, and they are used where a pump makes only a little pressure. Umbrella valves sit at 0.25 to 0.75 psi in a plastic body with no spring at all. The duckbill body is the smallest of the group and needs more than 5 psig of back pressure to seat reliably, which is a real limit rather than a footnote. Spring valves start at 0.5 psi and go to 10 psi, and are the ones to use where the line pressure is high enough to pay for the offset and where the reverse pressure has to hold a pump or a bottle.

PartTypeCrackingConnectionsBody and sealNote
CV7 seriesdiaphragm, free floating0.11 psimale or female Luer, or Luer to hose barbABS body, polysulfone insert, silicone diskISO 80369-7, smallest cracking figure on the page
CVJT seriesdiaphragm0.25 psi or less1/32, 1/16 and 1/8 inch barbsUSP Class VI materialsUSP Class VI, ISO 10993-1 and FDA 21 CFR 181.32
CVN, CVP, CVK seriesmolded diaphragm0.5 psi1/8 to 3/8 inch barb, 1/8 MNPTnylon, polycarbonate, PVDF or polypropylene bodyseal 1.9 psi, maximum 50 psi, silicone, Viton or neoprene diaphragm
CVNUCB-58-BU-1/2#spring1/2 psi5/8 inch barb, equalnatural nylon, Buna-Nspring tolerance plus or minus 30 percent
CVNUCB-58-BU-1#spring1 psi5/8 inch barb, equalnatural nylon, Buna-Ngeneral purpose water line
CVNUCB-58-EPDM-1#spring1 psi5/8 inch barb, equalnatural nylon, EPDMcaustic and hot water duty
CVNUCB-58-BU-3#spring3 psi5/8 inch barb, equalnatural nylon, Buna-Nneeds 2.1 m of water head to open
CVNUCB-516-V-3#spring3 psi5/16 inch barb, equalnatural nylon, Vitonsolvent and acid duty
CVNUCB-516-V-10#spring10 psi5/16 inch barb, equalnatural nylon, Vitonfor a line that holds pressure against a pump
F2804410075A8NVumbrella0.75 psi1/4 inch barbnylon body, Viton umbrella1.80 scfm forward at 5 psi, reverse under 0.06 SCIM at 1 psi
F2804410025I7PPVumbrella0.25 psi3/16 inch barbpolypropylene body, Viton umbrellalowest cracking figure in a barbed plastic body
CKV-M3duckbillunder 0.5 psig5 mm hex body, barbed or threaded optionsbrass or 303 stainless, about 2 g250 psig back pressure, orifice 0.035 to 0.040 inch, needs over 5 psig back pressure to check
SV11-125-44poppet shuttleunder 1.0 psi1/8 NPT female output, two inputspneumatic bodyCv 0.48, 0 to 125 psi, 15.0 scfm at 50 psi and 33 scfm at 125 psi
MJSV-1poppet shuttleabout 1 psig to shift1/8 NPTpneumatic body300 psig maximum, 30 scfm at 50 psig, not a pressure selector
R431003347diaphragm shuttle, inline1 psi differential1/8 NPTpneumatic bodyCv 1.25, 200 psi maximum, minus 40 to 160 F

Matching a Check Valve to the Line

The same line can be protected four ways, and the choice follows from the pressure the pump makes and the pressure the valve has to hold back. The table is the short version of that decision.

SituationValve to useWhyWhat to check
Gravity fed reagent bottle, no pumpdiaphragm at 0.11 to 0.25 psibottle head is under 1 psi, so a spring valve would never openthe head height and the tube bore
Peristaltic pump outlet against a closed valvespring at 3 to 10 psithe pump makes pressure, and the spring holds it back when the pump stopsthe pump pressure at the working flow
Solvent line through a pumpViton or PVDF wetted partsBuna-N and nylon swell in solventsthe seal list against the reagent list
Disposable patient linediaphragm in USP Class VI materialsthe line is thrown away and has to meet a biocompatibility classthe class and the Luer standard
Two pneumatic inputs, one cylindershuttle valvethe higher pressure wins without a control signalthe pressure difference needed to shift, about 1 psi
Two liquid sources into one linetwo check valves into a teea shuttle valve is an air part, and its dead volume is largerthe cracking pressure of both valves

Key Features

Cracking pressure per part – from 0.11 psi at a Luer port to 10 psi on a barbed spring valve, written next to the part instead of a range for the family.

Spring tolerance stated – plus or minus 30 percent, so a 3 psi nominal valve is understood as 2.1 to 3.9 psi before it is ordered.

Head height in plain terms – 0.11 psi is about 77 mm of water and 3 psi is about 2.1 m, which is the comparison that decides a gravity fed line.

Body and seal listed separately – nylon, polypropylene, PVDF and polysulfone bodies with silicone, EPDM, Viton or Buna-N seals, so the reagent check is made on the right column.

Four checking principles – diaphragm, umbrella, duckbill and spring, because the cracking range follows the principle more than the body size.

Duckbill limit stated – the CKV-M3 needs more than 5 psig of back pressure to check reliably, and that limit is on the page rather than in a footnote.

Shuttle valves kept separate – cracking under 1 psi and Cv 0.48 to 1.25 on air and inert gas, with a note that two check valves into a tee is the liquid answer.

Cleanliness classes – USP Class VI, ISO 10993-1, FDA 21 CFR 181.32 and ISO 80369-7 listed on the families that carry them.

Applications

Four places where the cracking pressure decides the part rather than the port size.

Reagent bottle anti siphon – a diaphragm valve at 0.11 psi under the bottle cap stops the line draining back into the bottle when the pump stops, and it opens on the small head the bottle provides.

Pump outlet protection – a spring valve at 3 psi on the outlet of a diaphragm pump keeps the reagent from being pulled back through the pump head when the inlet valve closes.

Wash line isolation – a Viton seated valve separates the wash bottle from the sample path, so a wash step does not dilute the sample left in the needle.

Pneumatic cylinder selection – a shuttle valve lets a manual button and a controller output drive the same cylinder without a logic valve in between.

On a fluidic panel the valves sit below the electronics, so the SUPERB PCBA and the SUPERB PCB stay clear of the drip line and a weeping seat does not reach a connector.

Sourcing and Cross-Reference

The first question on a check valve order is the pressure budget, not the port. A line that makes 1 psi cannot use a 3 psi spring, and the mistake is usually found after the valve is fitted, when the pump runs and nothing moves. Send the head height, the pump pressure at the working flow and the back pressure the valve has to hold, and the cracking pressure follows from those three numbers.

The second question is the reagent. A nylon body with a Buna-N seal is the default and covers water based reagents; a solvent needs Viton or PVDF, and a caustic wash needs EPDM or polypropylene. A valve that passes a water test can still swell on a cleaning solution, and the swelling shows as a seat leak a week later rather than at the bench.

The third question is the tube, because a barb is sized to the tube the method already uses and an adapter adds a joint that can weep. For a disposable or a patient contact line, the Class VI and ISO 10993 declarations have to come with the part. See medical device components for the documentation side, and BOM shortage recovery where one valve is holding up a build.

The SUPERB Assembly team pressure tests each valve seat after it is fitted, because a check valve that leaks backwards is invisible until a blank run comes out high.

Q: Can you supply a 0.5 psi cracking check valve in PVDF with a 1/8 inch barb, and quote the same body with a Viton seal for a solvent line?

A: Yes. Send the head height, the pump pressure, the back pressure and the reagent, and the SUPERB Tech team returns the cracking pressure, the body and the seal that fit.

Why Instrument Builders Source Check Valves Through SUPERB

  1. Cracking pressure first: the quotation starts from the pressure the line can make, so a valve that cannot open is not offered.
  2. Seal against the reagent: body and seal are separate columns, and the wetted material is confirmed against the reagent before the order.
  3. Matched barb sizes: 1/32 to 3/4 inch barbs, Luer and NPT are listed per part, so the valve fits the tube rather than the other way round.
  4. Air and liquid kept apart: shuttle valves are quoted for pneumatic duty and liquid selection is done with two check valves, which keeps the dead volume small.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Solenoid and Pinch Valves for Fluid Handling, Peristaltic and Diaphragm Micro Pumps, Liquid Flow Sensors for Medical and Analytical Instruments, Quick Disconnect Couplings and Luer Fittings, Air Bubble Detectors for Infusion and Reagent Lines, Differential Pressure Sensors for Ventilators, Medical Device Components, BOM Shortage Recovery.