Contact Us
  • Home
  • COMPONENTS
  • Quick Disconnect Couplings and Luer Fittings for Reagent Lines

Quick Disconnect Couplings and Luer Fittings for Reagent Lines

A coupling on a reagent line is opened every time a bottle is changed, and what it does at that moment decides whether the instrument needs a wipe down. The parts below split into valved quick disconnects that shut both halves on separation, and luer fittings that join small bore tubing inside a manifold. Flow coefficients run from 0.6 on a non spill coupling to 1.4 on a quarter inch valved coupling, and the spill volume per disconnect is quoted on the non spill version. Each entry lists pressure, temperature, wetted material and tubing size, because a coupling is chosen by the tube it has to fit before it is chosen by the flow.
quote now

Product Specifications

Product Overview

A quick disconnect does two jobs at once: it holds a tube joint that has to come apart, and it stops the liquid when it does. On a reagent bottle the second job matters more than the first, because a drip at every bottle change ends up on the instrument floor and in the service log. A valved coupling closes both halves as they separate, and a non spill coupling is shaped so that the small volume left in each half stays inside instead of running down the outside.

The first figure to compare is the flow coefficient against the tube bore. A coupling with a Cv of 0.6 on a quarter inch line is a restriction, and on a gravity fed reagent line that restriction becomes a slow fill rather than a fast one. The second is the pressure and temperature pair, because the same body is rated differently for water and for a warm cleaning solution, and a coupling chosen on pressure alone can be outside its temperature rating at the cleaning step.

The third figure is the wetted material. Acetal bodies with Buna-N seals are the general purpose choice for mild reagents, and they are not the choice for a solvent or for a strong base. A luer fitting in nylon is fine for a small bore sample line and is not fine for a line that is autoclaved. The material list on the coupling has to match the reagent list on the bottle, and that check is the one that gets skipped when a coupling is bought as an accessory.

The fourth point is the tubing interface. A hose barb takes a push fit and a clamp, a threaded port takes a fitting, and a panel mount puts the coupling through the wall of the instrument so the tube does not have to be reached inside. Getting that wrong costs an adapter, and every adapter is another joint that can leak. The parts on this page are listed with their termination so the panel layout can be made from the same table.

Key Specifications

ParameterValueNote
Coupling typesvalved and non valved quick disconnects, plus luer fittingsa valved coupling closes both halves on separation
Working pressurevacuum to 120 psi, 8.3 bar on both the quarter inch and the non spill familiesthe body rating, not the tube rating
Temperature0 to 71 C on the non spill family, minus 40 to plus 82 C on the quarter inch valved familya warm cleaning step has to be inside this range
Flow coefficientCv 0.6 on the non spill coupling, 1.40 maximum on the quarter inch family, 0.82 and 0.51 on the reduced bore versionsa coupling is a restriction and the Cv says how much
Spill volumeunder 0.10 cc per disconnect at all rated pressures on the non spill familythe figure that decides whether a bottle change needs a wipe
Air inclusion0.26 cc per connect on the non spill familyair in the line is read as a bubble by a flow sensor
Body materialsacetal on the quarter inch family, with 316 stainless internal springs and stainless external latchmild reagents only
SealsBuna-N as standard, other materials availablethe seal is the part the reagent attacks
LubricantKrytox PFPE on the non spill familyinert, so it does not react with the reagent
Tubing range1/4 to 3/8 inch, 6.4 to 9.5 mm on the quarter inch familytube size is chosen before the coupling
Luer fittingsfemale luer to 1/16 inch hose barb in nylonsmall bore lines inside a manifold
Terminationshose barb, pipe thread in NPT and BSPT, panel mount, in linea panel mount keeps the tube inside the instrument
Mating rulethe quarter inch family mates with the metal and polypropylene versions of the same seriesdifferent series with the same bore do not mate
Cleaningthe non spill family is quoted for cleaning in place at its rated temperaturecheck the seal before a caustic wash

Included Models and Order Codes

The table lists the parts that cover a reagent bottle, a panel pass through and a manifold joint. The non spill insert and body pair is the one to use where a bottle is changed with liquid in the line, because the spill figure is under 0.10 cc per disconnect. The quarter inch valved family covers the same duty at a lower cost and a higher flow coefficient, with a valved insert quoted as PLCD 240-04 and an unvalved insert as PLC 240-04, both on 1/4 inch NPT. The panel mount valved insert PLCD42004 puts the joint through the instrument wall on a 1/4 inch hose barb, and the luer fitting LF2131 joins a 1/16 inch tube inside a manifold.

PartTypeTerminationFlowNote
CPC NS4 insert and bodynon spill, valved both halveshose barb and threadCv about 0.6under 0.10 cc spill per disconnect, 8.3 bar, 0 to 71 C
CPC PLCD 240-04quick disconnect, valved insert1/4 inch NPT maleCv 1.40 maximumacetal body, Buna-N seal, 8.3 bar, minus 40 to plus 82 C
CPC PLC 240-04quick disconnect, unvalved insert1/4 inch NPT maleCv 1.40 maximumstraight through, for a line that is already shut off
CPC PLCD 240-040quick disconnect, valved insert1/4 inch BSPT maleCv 1.40 maximumthe BSPT thread for a European panel
CPC PLCD 240-060quick disconnect, valved insert3/8 inch BSPT maleCv 1.40 maximumlarger thread on the same body family
CPC PLCD42004quick disconnect, valved panel mount insert1/4 inch hose barbCv 1.40 maximumpanel mount, so the tube stays inside the instrument
CPC LF2131luer fittingfemale luer to 1/16 inch hose barbsmall borenylon body, black, for manifold joints

Choosing a Coupling for a Reagent Bottle

The same bottle can be connected four ways, and the choice follows from how often it is changed and what is in it. The table is the short version of that decision.

SituationCoupling to useWhyWhat to check
Bottle changed daily with liquid in the linenon spill valved pairunder 0.10 cc spill per disconnectthe seal material against the reagent
Bottle changed weekly, line emptied firstvalved insert on a quarter inch bodythe valve already stops the flowthe tube bore against the Cv
Panel pass throughpanel mount insertthe joint sits in the wall, not insidethe panel cut out and the thread
Manifold joint inside the instrumentluer fittingsmall bore, low dead volumethe barb size against the tube
Line that is clamped off anywayunvalved insertno valve to cleanthe clamp is the shutoff, so it must be rated
Cleaning in place with a warm solutionnon spill pair at its rated temperaturethe body and the seal are rated for itthe temperature and the caustic concentration

Key Features

Spill volume stated – under 0.10 cc per disconnect is the figure that decides whether a bottle change needs a wipe down.

Air inclusion stated – 0.26 cc per connect, because air in a reagent line is read as a bubble by the flow sensor downstream.

Flow coefficient per part – Cv from 0.6 to 1.40, so the restriction is known before the line is built.

Pressure and temperature together – 8.3 bar and 71 C on one family, 8.3 bar and 82 C on the other, both written next to the part.

Panel mount option – the joint can sit in the instrument wall, which keeps the tube out of the way of the door.

Mating rule stated – the quarter inch family mates with the metal and polypropylene versions of the same series, and same bore parts from other series do not.

Inert lubricant – Krytox PFPE on the non spill family, so the lubricant does not react with the reagent.

Luer for manifold joints – a female luer to 1/16 inch barb joins small bore tubing with a low dead volume.

Applications

Three joints where the spill volume and the termination decide the coupling rather than the flow.

Reagent bottle connection – a non spill pair on the bottle cap keeps the bench dry when a bottle is swapped with liquid still in the line.

Instrument panel pass through – a panel mount insert puts the joint in the wall, so the tube does not have to be reached past the door.

Manifold and probe joints – a luer fitting joins 1/16 inch tubing inside the fluidic manifold, where the dead volume matters more than the flow.

A fluidic panel is a set of joints on a plate, so the SUPERB PCBA and the SUPERB PCB are mounted above the drip line and the couplings are kept below it.

Sourcing and Cross-Reference

The first question on a coupling build is the reagent list. Acetal and Buna-N cover mild reagents and are the wrong choice for a solvent, and a coupling that passes a water test can swell on a washing solution. The second question is the tube, because the barb size and the Cv have to match the bore that the method already uses.

The second question is what happens at a disconnect. A non spill pair keeps the spill under 0.10 cc, which is the difference between a clean change and a service call. A valved insert on a cheaper body stops the flow but leaves a film on the outside, and that film is what attracts dust and crystals.

The third question is the panel. A coupling inside the instrument has to be reached with the door open, while a panel mount is reached from outside, and that changes the service time on every bottle change. See lead time and availability for a specific coupling and BOM shortage recovery where a build is held up by one part.

The SUPERB Assembly team wet tests every joint before the panel is closed, because a coupling that weeps shows up as a dried crystal a week later.

Q: Can you supply the coupling as a matched pair, with the insert and the body quoted together so the two halves mate?

A: Yes. Send the reagent, the tube size, the pressure and the panel cut out, and the SUPERB Tech team returns the mating pairs that fit.

Why Instrument Builders Source Couplings Through SUPERB

  1. Matched pairs: the insert and the body are quoted together, because two halves from different series with the same bore do not mate.
  2. Spill figure stated: the volume lost per disconnect is written down, which is what a clean room bottle change is judged on.
  3. Seal against the reagent: the wetted material list is quoted next to the part, so a solvent line is not built with a water coupling.
  4. Termination listed: barb, NPT, BSPT and panel mount are separate lines, so the panel layout comes from the same table.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Solenoid and Pinch Valves for Fluid Handling, Peristaltic and Diaphragm Micro Pumps, Liquid Flow Sensors for Medical and Analytical Instruments, Water Quality Sensor Circuits for pH and Conductivity, Wire to Board Crimp Housings and Headers, BOM Shortage Recovery.