Contact Us

STM8S207S8T6

Brand: ST
ST STM8S207S8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8S207S8T6 — MCU & Embedded Processors | Superb Automation

STM8S207S8T6

ST — MCU & Embedded Processors

Product Overview

The STM8S207S8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8S207S8T6: 64 Kbyte Flash STM8S MCU in LQFP44

STM8S207S8T6 is the 64 Kbyte Flash member of the STM8S 8-bit line in a LQFP44 body (10 by 10 mm), with 1536 bytes of true data EEPROM, 6 Kbyte of RAM, 34 general purpose I/O, 9 analog inputs and 15 high sink outputs. The core runs at up to 24 MHz and the supply range is 2.95 to 5.5 V. There is no controller area network block in this order code; the CAN member of the same body is listed in the cross reference.

Order code and memory

Order codeSTM8S207S8T6
Program Flash64 Kbytes
Data EEPROM1536 bytes, 300 kcycle endurance
RAM6 Kbytes
PackageLQFP44, 10 by 10 mm
Pin count44
Maximum general purpose I/O34
External interrupt pins31
High sink outputs15
ADC channels9 of 16
Controller area networknot present
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage2.95 to 5.5 V
Maximum CPU clock24 MHz up to 105 C ambient
Flash accesszero wait states to 16 MHz
CoreHarvard, 3 stage pipeline, 80 instructions, 20 addressing modes
Timersadvanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, 8-bit basic timer
Analog to digital converter10-bit, 9 channels, scan mode, analog watchdog, 14 clock cycles per conversion
ADC clock1 to 4 MHz with VDDA 3 to 5.5 V, 6 MHz above 4.5 V
Serial interfacesUART at up to 1 Mbit/s with LIN master mode, SPI up to 10 Mbit/s, I2C up to 400 kHz
Run current11.0 mA typical at 24 MHz from Flash on 3.3 V, 18 mA maximum
Low powerhalt 6.5 uA typical at 5 V, active halt 200 uA with the main regulator on and 11 uA with it off
Resetpower-on reset 2.65 to 2.88 V, brown-out reset 2.58 to 2.73 V, 70 mV hysteresis
Identification96-bit unique ID, single wire interface module for debug and programming

Points to check before this part goes on a BOM

This code puts a 64 Kbyte Flash array and 1536 bytes of data EEPROM into the 44-pin body, which is the highest memory combination available on 34 I/O without moving to the 64-pin footprint. The RAM stays at 6 Kbytes, so a larger program does not buy a larger working set.

The 44-pin package does not bond the VREF pins, and it exposes 9 of the 16 analog channels. Boards that were prototyped on a 64-pin evaluation board and then shrunk to 44 pins normally lose five analog inputs and the external reference in the same step, so the analog channel map should be fixed against the final package.

At 24 MHz the part draws 11.0 mA typical from Flash at 3.3 V and 4.0 mA with code in RAM, both well inside the 443 mW package rating at 85 C. The number that limits a sealed enclosure is usually not the MCU but the regulator and the high sink outputs driving LEDs.

Where this order code fits

Appliance control boards and instrument front ends that need 64 Kbytes of program space in a 10 by 10 mm footprint, with 8 CAPCOM channels for PWM and capture. Firmware teams comparing it against a neighbouring memory size or pin count usually start from our MCU Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Consolidation page. Both list the resource differences that decide the choice before any code is written.

Questions buyers ask

Is 64 Kbyte the top of the 44-pin line? No. STM8S207SB carries 128 Kbytes on the same 44-pin body with 1536 bytes of EEPROM, so the package supports the full range.

How many timers are there? One 16-bit advanced control timer with 4 CAPCOM channels and 3 complementary outputs, two 16-bit general purpose timers with 2 and 3 channels, one 8-bit basic timer, plus the auto wakeup, window and independent watchdogs.

What is the EEPROM endurance? 300 kcycles for the data array, against 10 kcycles for the program Flash, with 20 years of retention at 55 C.

SUPERB holds and sources ST microcontroller lines like this one for production and repair demand, with date codes, packing and quantity breaks quoted against the exact ordering string rather than the base name. When a line is changing, the Strategic Sourcing page walks through the checks that keep a substitute from failing on the bench.