Contact Us

STM8L152C8T6

Brand: ST
ST STM8L152C8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM8L152C8T6 — MCU & Embedded Processors | Superb Automation

STM8L152C8T6

ST — MCU & Embedded Processors

Product Overview

The STM8L152C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM8L152C8T6: 64 Kbyte ultra-low-power STM8L MCU in LQFP48

STM8L152C8T6 is a 64 Kbyte Flash member of the STM8L ultra-low-power line in a LQFP48 body (7 by 7 mm), with 4 Kbytes of RAM, 2 Kbyte of data EEPROM, 41 general purpose I/O, 25 channels on the 12 bit converter and 2 channel of 12 bit DAC. The supply range is 1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it and the core runs at up to 16 MHz. It also carries a segment LCD controller driving 8x24 or 4x28 segments with step up converter.

Order code and memory

Order codeSTM8L152C8T6
Program Flash64 Kbytes
Data EEPROM2 Kbyte with ECC and read while write
RAM4 Kbytes
PackageLQFP48, 7 by 7 mm
Pin count48
Maximum general purpose I/O41
ADC channels25 of the 12 bit converter
DAC channels2 of 12 bits with output buffer
LCD controller8x24 or 4x28 segments with step up converter
Temperature gradesuffix 6, minus 40 to plus 85 C

Electrical and peripheral parameters

Supply voltage1.65 to 3.6 V without brown out reset, 1.8 to 3.6 V with it
Maximum CPU clock16 MHz, 16 MIPS peak
Run current200 uA per MHz plus 330 uA static
Halt current400 nA typical
Active halt1.4 uA typical with the real time clock running
Low power modes5.9 uA typical in low power run, 3 uA in low power wait
Wake up time4.7 microseconds from halt
Analog to digital converter12 bit, up to 1 Msps, 25 channels, internal reference voltage and temperature sensor on chip
Digital to analog converter2 channel of 12 bits with output buffer, 7 microseconds typical settling into 5 k and 50 pF
Comparators2, one fixed threshold and one rail to rail, both can wake the core
Timersthree 16 bit general purpose timers, one 16 bit advanced control timer with three channels, one 8 bit timer, beeper timer, window and independent watchdog
Serial interfacestwo SPI blocks, one I2C at 400 kHz, three USARTs with ISO 7816 and IrDA
DMA4 channels covering the ADC, both DAC channels, I2C, SPI1, SPI2, USART1 to USART3 and the five timers
Data EEPROM endurance300 kcycle with ECC and read while write
Program memory endurance10 kcycle, 30 years retention at 85 C
Identification96 bit unique ID, single wire interface module, USART bootloader

Points to check before this part goes on a BOM

Sixty four Kbytes of Flash, 4 Kbytes of RAM and 2 Kbytes of EEPROM in the same 48 pin body as the C6 is the top of the medium plus density range, and it is the part to reach for when the application has outgrown both the program array and the working set. The RAM figure is the one that changes the architecture: 4 Kbytes allows a display buffer, a protocol queue and a metrology history to coexist, which the 2 Kbyte parts cannot do. The EEPROM also doubles to 2 Kbytes, enough for a full calibration set plus a tamper log.

The peripheral set is wider than the 32 Kbyte members of the same body. There are two SPI blocks and three USARTs instead of one each, so a product can run a radio on SPI, a host link on one USART and a service port on another at the same time, and the two 12 bit DAC channels can drive a 4 to 20 mA loop and a reference output together. That combination is what makes this order code common in transmitters and analyzers rather than only in meters.

The converter keeps 25 channels on 48 pins, with the fast channel available for the highest sample rate, and the LCD controller supports 8 by 24 or 4 by 28 segments with the internal step up converter. Halt current is 400 nA and active halt with the clock is 1.4 uA on this density, slightly above the 32 Kbyte parts, so a product that lives entirely on a coin cell should compare the two figures rather than assume they are the same across the family.

Where this order code fits

Process transmitters with a local display, analyzers with two analog outputs, metering gateways that log to a 2 Kbyte EEPROM, and instruments that need three serial links. Teams comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and teams replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What is the difference between the C8 and the C6? Double the Flash (64 against 32 Kbytes), double the RAM (4 against 2 Kbytes), double the EEPROM (2 against 1 Kbytes), two DAC channels instead of one, two SPI blocks and three USARTs against one each, and a wider LCD segment count. The package and pinout are the same.

How many ADC channels are usable? 25 on the 48 pin body, including the fast channel used for high sample rate work. The converter is 12 bit and reaches 1 Msps on that channel.

Is the EEPROM still read while write? Yes, with ECC and 300 kcycle endurance, 2 Kbytes on this density against 1 Kbyte on the 32 Kbyte parts.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.