Contact Us

STM32F101R8T6

Brand: ST
ST STM32F101R8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101R8T6 — MCU & Embedded Processors | Superb Automation

STM32F101R8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F101R8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101R8T6: 64 Kbyte, LQFP64 body

STM32F101R8T6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 64 Kbytes of Flash, 10 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101R8T6
Program Flash64 Kbytes
SRAM10 Kbytes
PackageLQFP64, 10 x 10 mm, 64 pins
Maximum general purpose I/O51
Analog input channels16 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersthree 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacesthree USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins
DACnot present on this line
Stop current14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply
Standby current2 uA typical and 4 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

R is the 64 pin LQFP at 10 x 10 mm and 8 is 64 Kbytes of Flash. Table 2 of DocID13586 puts the 64 pin medium density row at 10 Kbytes of SRAM, 51 general purpose I/O, 16 converter channels, three USARTs, two SPI and two I2C blocks, with three general purpose timers and a 36 MHz core.

This is the smallest body in which all 16 converter channels are bonded out. A 48 pin part stops at 10 channels, so a board that starts on the 48 pin footprint and later needs the extra six inputs has to change the board, not just the order code.

The 7 channel DMA controller serves the converter, the SPI blocks, the I2C blocks and the USARTs, which is what makes a 36 MHz core enough for a three phase control loop or a two channel data logger. Stop current on the medium density tables is 14 uA typical and 180 uA maximum at 85 C from 3.3 V, so a battery product still has to plan for the maximum figure and not the typical one.

The LQFP64 body is rated 45 C/W, so at 85 C ambient the junction margin of 20 C allows 444 mW of total dissipation. That is a wider budget than the 48 pin part and it is one of the reasons this body is the default for boards that drive outside loads.

Both debug ports are available: serial wire debug on two pins and JTAG on five, with the trace port as a further option. On a 51 I/O body that is a small share, but the pins only come back to the application once the debug port is switched off in the option bytes, which is worth deciding before the connector assignment is fixed.

Where this order code fits

It is the 64 Kbyte, 64 pin medium density part, the first body where the full 16 converter channels and three USARTs are available. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How many converter channels are usable? All 16 in this package. The 36 and 48 pin medium density parts bring out 10, so the channel count follows the pin count rather than the Flash size.

What is the standby current? 2 uA typical and 4 uA maximum in standby on the medium density tables, with the low speed internal oscillator running and the independent watchdog off. The RTC with its 32 kHz oscillator adds to that figure.

Does it have a DAC? No. A 12 bit DAC appears on the high density and XL density parts only. On the medium density line an external DAC over SPI is the usual route.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the ADC DAC Cross Reference page sets out the checks that keep a substitute from failing on the bench.

The ordering scheme ends with an options field: TR marks tape and reel and xxx marks a programmed part, so a code without either names a tray device and packing has to be stated separately on the order. The check that matters on a 64 Kbyte medium density part is the analogue front end, because all 16 converter channels share pins with the GPIO, and a board that later adds a digital function to a channel pin loses that input. The converter converts in 1 microsecond, so a 16 channel scan at full rate takes 16 microseconds and the channel count is usually limited by pin sharing rather than by conversion speed.