Contact Us

VBQG1410

Brand: VBsemi
VBsemi VBQG1410 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG1410 — Discrete & Power Semiconductors | Superb Automation

VBQG1410

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG1410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG1410: a 40 V N channel switch at 10 milliohm in a 2 by 2 DFN

The VBQG1410 is an N channel trench MOSFET in a 2 by 2 millimetre DFN, and it is the first part in this band where the package, not the die, sets the rating. The product summary prints 10 milliohm typical at a 10 V gate and 10 A, and 12 milliohm typical at 4.5 V and 9 A, against a 40 V drain to source rating. The absolute maximum table adds the current ladder, 12 A with the case at 25 C, 9.6 A at a 70 C case, 9 A in 25 C air and 6.3 A in 70 C air, and the dissipation that goes with it is only 4.1 W at a 25 C case.

The part is aimed at one job, and the feature list says it plainly: high side synchronous rectifier operation, with notebook CPU core high side switch named as the application. That is a position where the device switches at hundreds of kilohertz, carries a few amps, and sits next to a controller that wants a small gate charge and a low threshold. The 4.5 V threshold figure of 1.5 V typical and the 15 nC gate charge at a 10 V gate are the rows that matter there, not the 12 A headline.

The avalanche rows are unusual at this size. A single pulse avalanche current of 20 A at 0.1 mH and an energy of 21 mJ, with 100 per cent unclamped inductive switching testing named in the feature list, means the part is characterised for the energy stored in a small inductor when a load is interrupted. On a 40 V rail that is the difference between a switch that survives a cable unplug and one that does not, and very few 2 by 2 parts publish the row at all.

What the part cannot do is dissipate. 4.1 W at a 25 C case through a 25 C per watt junction to foot path is 102 C of rise, which puts the junction at 127 C before any margin, so the 12 A row exists only for a drain pad tied to copper. At the 2.2 W the sheet allows in 25 C air the same 10 milliohm gives 14.8 A by arithmetic, and the printed 9 A is the conservative reading of the same fact.

The parameter table in full

Drain to source voltage40 V
Gate to source voltage, continuousplus or minus 20 V
On resistance at 10 V gate and 10 A10 milliohm typical
On resistance at 4.5 V gate and 9 A12 milliohm typical
Continuous drain current, case at 25 C12 A
Continuous drain current, case at 70 C9.6 A
Continuous drain current, ambient at 25 C9 A
Continuous drain current, ambient at 70 C6.3 A
Pulsed drain current36 A
Continuous source to drain diode current, case at 25 C4.8 A
Continuous source to drain diode current, ambient at 25 C2.0 A
Single pulse avalanche current at 0.1 mH20 A
Single pulse avalanche energy21 mJ
Maximum power dissipation, case at 25 C4.1 W
Maximum power dissipation, case at 70 C2.5 W
Maximum power dissipation, ambient at 25 C2.2 W
Maximum power dissipation, ambient at 70 C1.3 W
Junction to ambient, 10 s pulse39 C per watt typical, 55 maximum
Junction to ambient, steady state85 C per watt maximum
Junction to foot, steady state25 C per watt typical, 29 maximum
Operating junction and storage rangeminus 55 to plus 150 C
Gate threshold at 250 microamp1.5 V typical
Breakdown voltage temperature coefficient26 mV per C
Gate leakage at plus or minus 20 Vplus or minus 100 nA
Drain leakage at 32 V, 25 C and 55 C1 and 10 microamp
On state drain current at 10 V gate20 A
Forward transconductance at 10 A50 S
Input, output and reverse transfer capacitance900, 165 and 73 pF
Total gate charge at 10 V gate15 nC typical, 23 nC maximum
Total gate charge at 5 V gate6.8 nC typical, 10.2 nC maximum
Gate source and gate drain charge2.5 and 2.3 nC
Gate resistance at 1 MHz0.36 minimum, 1.8 mean, 3.6 maximum ohm
Turn on delay and rise time at 4.5 V gate16 and 12 ns typical
Turn off delay and fall time at 4.5 V gate16 and 10 ns typical
Turn on delay and rise time at 10 V gate8 and 10 ns typical
Turn off delay and fall time at 10 V gate16 and 8 ns typical
Body diode forward drop at 9 A0.8 V typical, 1.2 V maximum
Body diode reverse recovery time and charge15 ns and 6 nC typical
PackageDFN 2 by 2 with exposed pad

What the thermal rows allow in a 60 C cabinet

The junction to foot path is 25 C per watt typical and 29 maximum, and the whole dissipation ladder follows from it. 4.1 W through 25 is 102 C of rise, 2.5 W through 29 is 72 C, and the 2.2 W the sheet allows in 25 C air through the 55 C per watt ambient path is 121 C of rise. Every one of those lands within a few degrees of the same 150 C limit, which is how a sheet looks when the rows were computed from one thermal model rather than measured separately.

For a build, the useful arithmetic is the reverse. With a 60 C cabinet and a 125 C allowed rise, the part can dissipate 2.3 W on the maximum foot path and 1.15 W on the steady state ambient path. One watt of conduction at 10 milliohm is 10 A, so the 2 by 2 body carries about 10 A with the pad on a ground plane and about 3.4 A on a board with no copper under it, which is the gap between the 12 A row and a real assembly.

The avalanche rows change that calculation in a useful direction. 21 mJ at 20 A does not depend on the copper at all, because the energy is dissipated in microseconds, so a load that dumps an inductor into the drain is handled by the die rather than by the board. A small solenoid, a relay coil or a short cable to a connector is comfortably inside 21 mJ; a 10 mH winding at 20 A, at 2 J, is not.

Where the printed rows in this sheet disagree

The first row that does not close is the current against the dissipation. Twelve amps through 10 milliohm is 1.44 W, which is inside the 4.1 W case row, so the current is thermally possible with the case clamped; but the same 12 A is 39 per cent of the pulsed limit of 36 A, and the sheet gives no safe operating area curve for the region between the two. For a synchronous rectifier that is tolerable, because the body diode carries the dead time, and for a load switch it means the pulse row is the only transient guidance available.

The second is the gate threshold. Only 1.5 V typical is printed, with no minimum and no maximum, on a part whose feature list advertises operation from a 4.5 V gate. A threshold distribution that is not published cannot be checked at cold start, and the turn on delay rows at 4.5 V, 16 ns on and 16 ns off, are typical rows for the same reason.

The third is the dielectric leakage row. Drain leakage is specified at 32 V rather than at the 40 V rating, which is normal practice, but the two ambient rows are printed at 25 C and 55 C rather than at a hot junction, so there is no leakage figure anywhere near the 150 C the part is rated to. For a battery product that has to hold a charge with the switch off, that missing row is the one that matters.

The fourth is minor and comes from the extraction rather than the silicon: the product summary row for the on resistance at 4.5 V lost its current column in the printed table, and the 9 A figure appears only in the specification page. We quote the specification page throughout.

Where a 40 V, 12 A part in a 2 by 2 body still fits

The intended position is a high side synchronous rectifier in a low voltage buck, where the drain sees the input rail, the current is a few amps and the switching frequency is high enough that a 15 nC gate charge is worth more than a milliamp of quiescent current. A 12 V to 1.2 V core rail at 300 kHz is the textbook case, and the 8 ns edges at a 10 V gate are what makes it work.

It also fits a small solenoid or relay driver, and there the avalanche row is the reason. Forty volts of headroom over a 24 V coil, 21 mJ of single pulse energy and 36 A of pulsed current cover the clamp without a snubber, and the 0.8 V body diode drop means a flyback diode can be the body diode itself if the duty cycle is low.

It does not fit a 40 V rail with transients above 40 V, because the drain rating is the rating and the breakdown coefficient of 26 mV per C does not give a hot part any more room than a cold one. It also does not fit a position that needs more than 3 A in air on a board without copper, which is a large share of the small boards this package was made for.

Our power management cross reference work carries the avalanche energy and the thermal paths per approved alternate for this size, because two 40 V parts at 10 milliohm in a 2 by 2 body can differ by a factor of three on the energy they absorb and by 15 C per watt on the path to the board.

Questions we answer before a reel is booked

The first is the copper. A 2 by 2 package at 4.1 W needs a drain pad with real area under it, and the difference between 25 and 55 C per watt is the difference between a 12 A row and a 6 A row. We ask for the pad area and the layer count before quoting the part into a build, since the same device on a two layer board and on a four layer board behaves as two different parts.

The second is the gate drive. At 4.5 V the part still switches in 16 ns and carries 6.8 nC, but the threshold is only a typical, so the cold start case has to be checked. At 10 V the charge doubles and the rise time improves, which is the trade a controller that can afford 10 V of gate swing should take.

The third is the avalanche rating in the actual circuit. 21 mJ is measured at 0.1 mH and 20 A, and a real coil has resistance that lowers the peak current and copper that absorbs part of the energy, so the number is a floor rather than a guarantee. Our incoming inspection plan holds the on resistance at both gate levels and the avalanche sample test for this family, and the pin to pin comparison starts from the 2 by 2 footprint and the pad geometry, because the lead frame under a 2 by 2 body is where the thermal row is decided.