HXC50187
Product Specifications
HXC50187
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50187 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50187: 250 W on a 32 V rail, the only 32 V part in the L band group
The HXC50187 is a 250 W LDMOS transistor on the HXC50 shelf, internally matched, single ended, on a 32 V rail, with 14 dB of gain and 55 per cent drain efficiency on the index row, marked CW. The vendor page puts the band at 960 to 1220 MHz, names the applications as L band avionics pulse or CW amplifier and ISM, and says the part can be used in Class AB, Class B and Class C. The page carries a Product Data Sheet link, and that link points at the site root and serves nothing, so the numeric detail behind the row is the index line plus a parameters block that is published as a picture rather than as text.
What that means for a buyer is narrow but important. The four figures a matching network is built from, the capacitance set, the breakdown voltage and the thermal resistance, are not published in a form that can be read and copied into a calculation. They exist on the vendor page as an image. Anything derived from them here is arithmetic on the index row, and the page says so in the table below rather than presenting a figure as published.
The 32 V rail is the first thing that separates this row from its neighbours. The 960 to 1215 MHz group is otherwise built on 50 V, and the lower frequency shelves carry 28 V. A part on 32 V sits between the two, which is what a 28 V avionics bus looks like after a boost stage and a margin, and it is also the rail that lets a single ended device reach 250 W at 1 GHz without the current of a 28 V part at the same power.
The HXC50187 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, internally matched, single ended |
| Output, index row | 250 W |
| Output in dBm, calculated | 53.98 dBm |
| Frequency range, index row | 0.96 to 1.2 GHz |
| Frequency range, vendor page | 960 to 1220 MHz |
| Drain rail, index row | 32 V |
| Gain, index row | 14 dB |
| Drain efficiency, index row | 55 per cent |
| Mode, index row | CW |
| Modes on the vendor page | Class AB, Class B and Class C, pulse and CW |
| Application list, vendor page | L band avionics pulse or CW amplifier, ISM |
| Output at 1 dB compression | Not published |
| Power added efficiency at any drive level | Not published, only the single 55 per cent row |
| Drain to source breakdown | Not published in text |
| Thermal resistance, junction to case | Not published in text |
| Input, output and feedback capacitance | Not published in text |
| Load mismatch tolerance | Not published |
| Junction temperature maximum | Not published in text |
| Package outline | Not published in text |
| Pulse width and duty limit | Not published |
| Data sheet link on the vendor page | Points at the site root, serves nothing |
| Parameters block on the vendor page | Published as a picture, not as text |
| Orderable addendum | None published |
| Packing quantity | Not published |
| Moisture sensitivity level | Not published |
| Marking and date code format | Not published |
What 250 W on 32 V means at the drain and at the connector
250 W into 50 ohm is 111.8 V rms and 158.1 V peak. Against a 32 V rail that peak is 4.94 times the supply, which is far beyond what a single ended drain can swing, and that ratio is the reason the part is internally matched. The match inside the package transforms the 50 ohm outside down to an impedance of a few ohms at the die, and the drain sees a swing of roughly two to three times the rail while the connector sees 158 V. Both statements are true at once, and confusing them is how a 100 V capacitor ends up on a 250 W output.
So the 158 V figure is the one that sizes the output network: the coupling capacitor, the circulator if there is one, the connector and the cable. At a 2 to 1 load the peak reaches 316 V and at 3 to 1 it reaches 474 V, and at those levels the passive parts fail long before the transistor does. On an avionics amplifier the output usually goes through a circulator or an isolator, which caps the load the transistor sees and is the cheapest insurance available on a 250 W board.
The supply side is the second calculation. At 55 per cent efficiency the part draws 454.5 W, which is 14.2 A at 32 V, and the heat to move is 204.5 W. At 50 per cent the current is 15.6 A and the heat 250 W. Those are not currents a small regulator can supply from a 28 V bus at good efficiency, which is a practical reason to check the converter before the transistor is chosen: a 32 V rail at 15 A is itself a procurement item with a lead time.
Thermal: nothing published, so the heat sink has to be measured
204.5 W of heat is enough to make the flange the centre of the thermal calculation. With no thermal resistance in text, the only honest way to size the heat sink is to work backwards from a target. If the flange holds 85 degrees and the junction limit is 225 degrees, the budget is 140 degrees; at 204.5 W that allows 0.68 degrees per watt. A flange at 0.5 degrees per watt gives a 102 degree rise and a junction near 187 degrees, which leaves margin. A poorer interface, a 0.8 degree per watt flange, reaches 249 degrees and is already over the limit.
Two consequences follow. The interface material matters as much as the heat sink, because a 0.1 degree per watt interface on a 205 W part is 20 degrees. And the case temperature has to be measured at full power in the intended housing rather than assumed from a similar part, because the entire calculation rests on a figure the vendor has not published here.
On a CW part there is no duty cycle to hide behind. Pulsed rows can be sized on average power; this one runs continuously at 250 W, so the heat is continuous too, and the ambient plus the flange rise is the whole story.
Drive, gain and the avionics band
At 14 dB of gain the drive for 250 W is 9.95 W, or 39.98 dBm. A 10 W driver is not a small part: it is a second transistor, its own bias loop, its own heat sink and its own matching, and on a two stage chain the driver often costs as much board area as the final. That figure is the strongest argument for looking at the 300 W row instead, which needs 6.0 W of drive at 17 dB, or at the 90 W row if the system can live with less output.
The band runs 960 to 1220 MHz, which covers the avionics interrogate and reply channels around 1030 and 1090 MHz with room at both ends, and reaches the lower edge of the 1.2 GHz region. Coverage is not the same as flatness: the page gives one band and one gain figure, and an internally matched part still moves a few tenths of a decibel across 260 MHz. Sweep the band on the fixture that will ship before the gain budget is frozen.
For ISM use the same row applies at 1.1 GHz or in the upper part of the band, and the CW marking is what matters there. ISM transmitters are usually continuous or high duty, so a row marked CW is the correct starting point and a pulse row would need a duty figure before it could be used.
Where the HXC50187 sits on the shelf
Inside the 960 to 1215 MHz group the rows run 90 W, 250 W, 300 W, 750 W, 900 W in a narrow band and 1000 W. In decibels the step from 90 W to 250 W is 4.44 dB and the step from 250 W to 300 W is 0.79 dB, so this row sits close to the 300 W row and well above the 90 W one. A requirement that lands within a decibel of 300 W is better served by the 300 W row, which needs less drive and publishes a higher efficiency.
Read as a choice, the 250 W row is for a 32 V system that wants a single ended part with a low current and a published CW rating, and that can live without a data sheet behind the link. A buyer on a 50 V bus takes the 300 W row and keeps the same band; a buyer who needs more output moves to the 750 W row and accepts 27 A of drain current.
Before the purchase order goes out
Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route that handles a part with a picture only parameters block is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 250 W L band part should work from the RF power transistor cross reference, which lines the two up on rail, gain and package rather than on the headline wattage. A bill of materials that includes the 10 W driver, the circulator and the output passives can be placed through the one stop RF supply route.