Contact Us

VBQF2311

Brand: VBsemi
VBsemi VBQF2311 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF2311 — Discrete & Power Semiconductors | Superb Automation

VBQF2311

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF2311 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF2311: a minus 30 V P channel in the 3 by 3 body

The VBQF2311 is a single P channel MOSFET in the DFN 3 by 3 body at minus 30 V drain to source, plus or minus 20 V on the gate, 9 milliohm at a minus 10 V gate and 17 milliohm at minus 4.5 V, minus 30 A of drain current, minus 2.5 V of threshold and a body diode that drops 1.2 V at its rated current. The applications named by the vendor are notebook battery charging and the notebook adapter switch, and both are places where a P channel is used to avoid a charge pump.

The economics of a P channel are different from an N channel. Hole mobility is about a third of electron mobility, so the same resistance needs roughly three times the die area, and at 30 V that penalty is still affordable in a 3 by 3 body. That is why 9 milliohm is available here and why a 60 V P channel in the same body is 50 milliohm. The break even between a P channel and an N channel with a charge pump sits near 30 to 40 V and near 3 A; above either, the N channel wins on cost and on loss.

The threshold of minus 2.5 V is the number that decides the drive. A P channel conducts when the gate is below the source, so a 12 V rail with the gate pulled to ground is 12 V of drive and the part is fully on. A gate driven from a 3.3 V logic pin through a level shift gives 3.3 V of drive, which is only 0.8 V below the threshold, and the part is not enhanced.

Key data for the VBQF2311

ConfigurationSingle P channel
PackageDFN 3 by 3, exposed pad
VDSMinus 30 V
VGSPlus or minus 20 V
VthMinus 2.5 V
RDS(on) at minus 10 V9 milliohm typical
RDS(on) at minus 4.5 V17 milliohm typical
ID at a 25 C caseMinus 30 A
Pulsed drain currentMinus 120 A
Body diodeMinus 1.2 V maximum at the rated current
RthJA26 K per watt typical, 33 maximum at 10 s
Junction rangeMinus 55 to 150 C

The resistance nearly doubles between the 10 V and the 4.5 V gate, 9 to 17 milliohm. That is the worst ratio in this band, and it is a direct consequence of the threshold being 2.5 V rather than 1.7 V: at 4.5 V of drive the part is only 2 V above threshold, so the channel is thin and the drift region is not accumulated. On a 12 V rail the drive is usually the full rail, and the 9 milliohm figure applies. On a 5 V rail the 17 milliohm figure is the working one, and an engineer who assumes 9 will be 90 per cent low on the loss.

The body diode is the reason a P channel is used in a battery path. With the drain towards the battery, the diode conducts from the load to the battery when the cell is present, which is the wrong direction for a charger but the right one for a protection switch. With the source towards the battery the diode blocks in the reverse condition, which is what reverse polarity protection needs. The 1.2 V maximum drop is the price of that arrangement, and at 3 A it is 3.6 W until the channel is on.

The battery and adapter switch

In a notebook battery path the part sits between the pack and the system rail, with the gate controlled by a charger IC that also monitors the current through a sense resistor. The 9 milliohm part at 4 A dissipates 0.14 W, which is nothing, and the reason the part is not smaller is the inrush when the adapter is plugged in. A 30 A pulsed rating and a 120 A pulsed drain current cover the moment the input capacitance charges, and the soft start on the charger IC limits the rest.

In an adapter switch, two of these form a selector between the adapter and the battery, and the body diodes are arranged so that the higher of the two sources feeds the rail. The gate of each is pulled to its own source by a resistor and pulled down by the charger, so the part conducts only when its own supply is present. This is the classic power path, and it is where the 1.2 V diode drop matters, because both diodes are in series with the load until the gate drive arrives.

The third place a 30 V P channel appears is reverse polarity protection on a 24 V input. Thirty volts is marginal there: a 24 V supply with a 10 per cent tolerance is 26.4 V, and a transient clamp at 33 V is above the rating. A 40 V P channel with the same current is the safer choice on that line, which is a separate code in the same family.

Drive, loss and the gate network

The gate network on a P channel is a resistor from gate to source, a resistor in series with the drive, and often a zener. The pull up holds the part off when the driver is unpowered. The series resistor sets the turn on time, which on a 100 microfarad load decides the inrush. A 10 k pull up and a 1 k series resistor give a turn on of tens of microseconds, which is slow enough to keep the inrush inside the 120 A pulsed rating.

The conduction loss at 4 A and 9 milliohm is 0.14 W. At 10 A it is 0.9 W, and at 20 A it is 3.6 W, which is the point where the 3 by 3 pad on four square centimetres of copper becomes the limit. Hot, the resistance rises by 40 per cent, so the 20 A figure is nearer 5 W and the junction rises 130 to 160 K. The honest continuous current for this body in still air is 10 to 12 A.

The gate to source limit is 20 V in both directions, and on a 24 V rail the gate sits at 24 V when the part is off, so a zener is mandatory. On a 12 V rail the limit is not reached and a resistor is enough. Where a part has to be substituted, the pin to pin cross reference page covers which parameters have to match before the swap, and on a P channel the threshold polarity and the body diode direction are the two that catch people.

Where the same P channel is carried across several boards and the original code has gone short lead, the obsolete RF part replacement page covers the route from a last time buy to a qualified substitute, including how the lot is verified before the board is released.

Buying this code

The page carries the resistance at two gate voltages, the current, the body diode drop and the thermal rows, and no gate charge figure and no avalanche rating. For a load switch that is enough. For a circuit that switches the part at a kilohertz or faster, the gate charge has to come from the data sheet, because the 3 by 3 body has a large gate for a P channel of this resistance.

Marking on a 3 by 3 body is a short code, and a P channel and an N channel of the same family can look identical on the reel. Where a line mixes both polarities, the incoming inspection plan page covers what is checked on receipt, from the reel label to a curve trace on a sample, before the parts reach the line.

Questions we get on this code

Can the gate be driven from a 3.3 V pin? Not directly. At 3.3 V below the source the part is barely on and the resistance is far above the 17 milliohm printed for 4.5 V. A small NPN or an open drain with a pull up to the rail is what drives it.

Is it a drop in for an N channel plus a charge pump? Electrically no. The gate reference, the drive polarity and the body diode direction all change, so the board changes with the part.

What is the 120 A pulsed figure for? The inrush into the load capacitance, which lasts microseconds. It is not a hot swap rating: the safe operating area is published for single pulses only.

Does the part block reverse current when it is off? Yes, through the body diode in one direction only. If the load can be at a higher voltage than the source with the part off, a second device back to back is needed.