Contact Us

VBQF2120

Brand: VBsemi
VBsemi VBQF2120 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF2120 — Discrete & Power Semiconductors | Superb Automation

VBQF2120

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF2120 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF2120: a minus 12 V P channel switch at 15 milliohm for a battery or PA path

The VBQF2120 is a P channel MOSFET with a minus 12 V drain to source rating and a 0.015 ohm on resistance at a minus 4.5 V gate, in a DFN 3 by 3 punch type body with a 0.62 mm profile. The summary prints three resistance points, 15 milliohm at minus 4.5 V, 21 at minus 2.5 V and 23 at minus 1.8 V, and a minus 25 A continuous rating at a 25 C case.

The application list names a PA switch, a battery switch and a load switch, which is exactly what a P channel part at this voltage is for. A P channel switch sits in the high side of a single cell or two cell rail and turns on with a gate pulled below the source, so the control signal can come from a logic pin without a charge pump. The trade is resistance: a P channel die of the same area has two to three times the resistance of an N channel, which is why a 12 V part prints 15 milliohm.

The three resistance points show how much the gate drive matters at this voltage. From minus 4.5 V to minus 1.8 V the resistance rises from 15 to 23 milliohm, 53 per cent, and a battery rail that sags to 1.8 V therefore loses more in the switch exactly when the load needs it most. A part driven from a rail-referenced logic pin needs the gate pulled to the source, not to ground.

The threshold window is minus 0.5 V to minus 1.5 V and the gate is rated to plus or minus 8 V, which is a narrow window for a 12 V rail. With the source at 12 V and the gate at 0 V the gate to source voltage is minus 12 V, which exceeds the minus 8 V limit. A P channel switch on a 12 V rail therefore needs a gate clamp or a series resistor and a Zener, and the sheet has no internal clamp.

The parameter table in full

Drain to source voltageminus 12 V
Gate to source voltage, continuousplus or minus 8 V
Continuous drain current, case at 25 C and 70 Cminus 25 A and minus 19 A
Continuous drain current, board at 25 C and 70 Cminus 20 A and minus 11 A
Pulsed drain currentminus 80 A
Continuous diode current, case at 25 Cminus 26.7 A in the ratings table, minus 8 A in the diode table
Continuous diode current, board at 25 Cminus 3.5 A
Maximum power dissipation, case at 25 and 70 C37 and 26 W
Maximum power dissipation, board at 25 and 70 C3.9 and 1.96 W
Junction to ambient, typical and maximum31 and 42 C per watt
Junction to ambient, steady state maximum72 C per watt
Junction to foot, typical and maximum13 and 16 C per watt
Breakdown voltage temperature coefficientminus 13.3 mV per C
Gate threshold temperature coefficient2.4 mV per C
Gate threshold at minus 250 microampminus 0.5 V minimum, minus 1.5 V maximum
Gate leakage at 5 Vminus 100 nA maximum
Drain leakage at minus 12 V, 25 C and 70 Cminus 1 and minus 10 microamp
On state drain current at minus 4.5 V gateminus 20 A minimum
On resistance at minus 4.5 V gate and 1 A0.015 ohm typical
On resistance at minus 2.5 V gate and 1 A0.021 ohm typical
On resistance at minus 1.8 V gate and 1 A0.023 ohm typical
Forward transconductance at minus 1 A8.3 S typical
Input, output and reverse transfer capacitance at 6 V2220, 865 and 555 pF
Total gate charge at minus 5 V and at minus 4.5 V38 and 35 nC typical
Gate source and gate drain charge7.3 and 5.9 nC
Gate resistance at 1 MHz, minus 0.1 V gate bias28 ohm
Turn on delay and rise time at minus 4.5 V drive14 and 25 ns typical
Turn off delay and fall time, same conditions380 and 240 ns typical
Body diode forward drop at minus 1 Aminus 0.65 V typical, minus 1.2 maximum
Body diode recovery time311 ns typical, 467 maximum
Body diode recovery charge1.136 microcoulomb typical, 1.705 maximum
Package reflow condition, IR and convection260 C, no hand soldering
Operating junction and storage rangeminus 55 to plus 150 C

Thirty seven watts on the case, and why the junction to foot row is the real one

The case row cannot hold with the junction to foot row. Thirty seven watts through 13 C per watt is 481 C of rise, and even the 16 C per watt maximum gives 592 C. The two rows describe different conditions, and the pair that does close is the current row and the thermal path: 25 A through 15 milliohm is 9.4 W, which through 13 C per watt is 122 C of rise and lands on a 147 C junction from a 25 C foot. The 37 W figure is the arithmetic of a much larger body.

On a board the allowance is 3.9 W through 31 C per watt, 121 C of rise and a 146 C junction in a 25 C room. Through 15 milliohm that is 16 A cold and 13 A at the 0.021 ohm figure, and the printed board rows of minus 20 A at 25 C and minus 11 A at 70 C bracket that estimate. The steady state row of 72 C per watt drops the allowance to 1.7 W and 10.6 A, which is the number for a small pad with no copper.

The gate resistance of 28 ohm is the largest in this shipment by a factor of twenty, and with 2220 pF of input capacitance the internal gate time constant is 62 ns. A 100 ohm external resistor dominates it, so the gate drive requirement is modest, and the 380 ns turn off delay plus 240 ns fall time show a part that is deliberately slow rather than a part limited by its driver.

Slow switching, a slow body diode, and two current tables

The switching rows are the most important feature of this sheet for a load switch and the least useful for anything else. At minus 12 V and 25 A a 240 ns fall time is 36 microjoule of crossover energy, which at 100 kHz is 3.6 W, comparable with the 9.4 W of conduction. At 1 kHz it is 0.036 W and irrelevant. A PA switch that changes state once per transmit slot is therefore the ideal use, and a DC to DC converter is the wrong one.

The body diode is very slow for a 12 V part. Recovery time of 311 ns typical and 467 ns maximum with 1.136 microcoulomb of charge gives about 3.7 A of average reverse current, which is consistent with the 1 A test current and a long tail. A P channel switch used in a path where the diode never conducts is unaffected, and one used across an inductive load is not.

The diode current appears as minus 26.7 A in the ratings table and minus 8 A in the diode table, a factor of three apart, with the board row at minus 3.5 A. The diode table figure is consistent with a 12 V P channel die of this size, and the ratings table row looks copied from the channel rating.

The package description disagrees with itself as well. Page one calls the body a DFN 3 by 3 punch type with a 0.62 mm profile, while note e refers to the body of a DFN 2 by 2 device. The land pattern on page one is the 3 by 3 one, so the note is inherited text from a smaller sibling.

Where a minus 12 V, 15 milliohm P channel earns its place

A PA power switch on a single cell radio, a battery disconnect on a two cell pack, a load switch on a 5 V or 12 V rail with a low duty cycle and a reverse polarity guard all fit. The 12 V rating suits a 5 V rail with margin and a 12 V rail only with a clamp, and the 15 milliohm resistance keeps a 2 A load at 0.06 W.

It does not fit a 12 V rail without a gate clamp, a converter above 10 kHz, or a synchronous path where the body diode conducts. The 8 V gate limit and the 467 ns recovery are the two rows that rule those uses out, and both are on the first two pages.

Our power management cross reference work keeps the gate resistance, the body diode recovery and the threshold window per approved alternate for P channel parts, because a substitute with a 5 ohm gate resistance and a 40 ns diode will behave as a different component in a battery switch even when the voltage and resistance match.

Questions we answer before a reel is booked

First, the gate clamp. The source sits at the rail and the gate is rated to minus 8 V, so on a 12 V rail the off state exceeds the limit unless a resistor divider or a Zener holds the gate within 8 V of the source. We ask for the rail voltage and the control signal level before approving the position.

Second, the duty cycle. A PA switch or a battery disconnect changes state rarely, and the 240 ns fall time costs nothing there. A converter or a PWM dimmer at 100 kHz would spend 3.6 W in crossover at 25 A, which is more than the conduction loss.

Third, the body. The sheet calls the part both a 3 by 3 and a 2 by 2, so we confirm the land pattern from the drawing rather than the note. The 0.62 mm profile rules out hand soldering, and the reflow row of 260 C is the only assembly route the sheet allows.

Fourth, the alternate, and here the incoming inspection plan checks the gate resistance and the threshold window on the arriving lot, while the pin to pin comparison starts from the punch type land pattern and the gate pin position, since a P channel part with the gate on the opposite side will not fit the same footprint.