Contact Us

VBQF1320

Brand: VBsemi
VBsemi VBQF1320 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1320 — Discrete & Power Semiconductors | Superb Automation

VBQF1320

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1320 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1320: a 30 V N channel in the 3 by 3 DFN

The VBQF1320 is a single N channel MOSFET in the DFN 3 by 3 body with an exposed pad, printed at 30 V drain to source, plus or minus 20 V on the gate, 21 milliohm at a 10 V gate and 25 milliohm at 4.5 V, with a 3.8 nC total gate charge and an 18 A drain current that the data sheet itself marks as package limited. The threshold sits at 1.7 V typical. It is the small body member of this band, and the numbers describe a part that a notebook rail or a load switch would use rather than a motor drive.

Thirty volts is the rating that covers a 12 V rail and a 24 V rail with a clamp. A 12 V battery line sits at 14.4 V in charge and can reach 18 to 20 V during a jump start, and a 24 V truck line sits at 28.8 V in charge. Both stay under 30 V steady state, and the clamp on the input takes the rest. A 30 V part also keeps the on resistance low, because the drift region is short, which is why 21 milliohm fits in a 3 by 3 body at all.

The body is 3.3 mm square with the pad underneath, so the thermal path runs into the board rather than through the package. That is the whole reason a 15.6 W figure at a 25 C case turns into 3.2 W at a 25 C ambient, and why the steady state junction to ambient resistance is published as 81 K per watt in the notes. Anyone who sizes from the 18 A headline and then finds the part at 130 C has skipped that line.

Key data for the VBQF1320

ConfigurationSingle N channel
PackageDFN 3 by 3, exposed pad
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
RDS(on) at 10 V21 milliohm typical
RDS(on) at 4.5 V25 milliohm typical
ID at a 25 C case18 A, package limited
ID at a 25 C ambient9 A
Pulsed drain current35 A
Qg3.8 nC typical
Ciss435 pF
Power at a 25 C case15.6 W
RthJA32 K per watt typical, 39 maximum at 10 s
Avalanche5 A, 1.25 mJ, 0.1 mH
Junction rangeMinus 55 to 150 C

Read together, the four resistance and current numbers describe a part that is fully enhanced at a 10 V gate, partly enhanced at 4.5 V and off once the gate rises within 1.7 V of the source. The 21 milliohm figure belongs to the first case and 25 milliohm to the second, a 19 per cent step, which is small because the threshold is low and the channel is short. Hot, the resistance roughly doubles by 125 C, so the working number for a 5 A load is 50 milliohm and 1.25 W, not the 0.5 W that the headline suggests.

The 18 A is a package figure. The bond wires and the lead frame set it, not the die, and it applies with the case held at 25 C. At a 25 C ambient the same part is rated 9 A, and at a 70 C ambient 7 A. On a board with 4 square centimetres of copper the practical continuous current is 6 to 8 A, and 10 A only with an inner plane vias into the pad.

Where a 30 V part in this body is used

The first case is a system power rail in a notebook or a handheld. The part sits as the switching element of a buck converter at 500 kHz to 1 MHz, carries 3 to 6 A, and the 3.8 nC gate charge is what makes that frequency affordable on a small controller. At 6 A and 25 milliohm the conduction loss is 0.9 W, and the switching loss at 800 kHz with a 12 V input is around 0.35 W, so the split matters and the part is chosen for the resistance at 4.5 V rather than at 10 V.

The second case is a load switch in the positive line of a 12 V rail. The source goes to the rail, the drain goes to the load, and the gate is pulled up to the rail through a resistor and pulled down by an open drain output. The load sees the rail with 21 milliohm in series, which at 3 A is 63 mV of drop. Nothing else in that path is as clean, and the part adds no quiescent current of its own.

The third case is reverse polarity protection on a battery input. The drain faces the battery and the source faces the load, so the body diode conducts when the battery is fitted the right way round and blocks when it is reversed, which means the circuit works before the gate drive is powered. The diode drop is the price, 0.7 to 1 V at a few amps, until the channel takes over.

Drive, switching and loss in a 3 by 3

At 3.8 nC of gate charge, the drive current at 1 MHz is 3.8 mA, which any controller can supply. The gate resistor sets the switching speed and the ringing, and 2 to 10 ohm is the usual window. Too small and the drain ringing reaches the 30 V limit on a long input trace; too large and the part spends time in the linear region, where the loss per switching event is the current times the voltage times the overlap.

The 435 pF input capacitance is small enough that a gate driver in a controller can drive two of these in parallel without a buffer. Two in parallel halve the resistance to 10.5 milliohm and double the gate charge to 7.6 nC, which is often cheaper than one larger part when the board area is already committed to the 3 by 3 footprint.

Where the original code on a board has gone short lead and a substitute has to be proposed, the how to verify a drop in replacement page covers the bench checks, from threshold and gate charge to the body diode direction, that decide whether the substitute behaves the same in the circuit. The 3 by 3 land pattern is common across several vendors, so the package is rarely the obstacle and the gate charge and the threshold usually are.

What to check before this code is bought

The data sheet carries electrical numbers and a halogen-free statement to IEC 61249-2-21, and no automotive qualification. A part for a vehicle rail needs an AEC-Q101 document, and this page is not that document, so it should be treated as an industrial part until one is produced. The 100 per cent gate resistance test is a process control, not a reliability grade.

Packing and marking matter on a part this small. The DFN 3 by 3 is laser marked on the top surface with a lot code that is hard to read after reflow, and the reel label is the only reliable record. Where a build needs traceability, the date code management page covers how lots are recorded and how a mixed reel is split before it reaches the line.

Where the code has to be compared with the alternative voltage classes in the same family, the power management cross reference page sets out which parameters have to match before a substitute is proposed, from the threshold and the gate charge to the avalanche rating.

Questions we get on this code

Is the 18 A a continuous rating on a board? No. It is a package limited figure with the case at 25 C. On a normal board the continuous current is 6 to 8 A, and the data sheet ambient rows, 9 A at 25 C and 7 A at 70 C, are the honest starting point.

Can the gate be driven from 3.3 V logic? Only through a level shift. At 3.3 V below the source the part is barely on and the resistance is well above the 25 milliohm printed for 4.5 V, so the loss is not the published one.

What happens if the load is inductive? The body diode clamps the drain to the source plus a diode drop, and the energy in the inductance has to go somewhere. On a small inductive load the avalanche rating of 1.25 mJ at 0.1 mH is the limit, and a freewheel diode is cheaper than finding out.

Does the part survive a hot plug? The pulsed rating is 35 A and the safe operating area is published for single pulses only, so a 12 V rail with 470 microfarad of input capacitance has to be charged through a resistor or a soft start. The 435 pF of input capacitance is the part itself, not the load.