Contact Us

VBQF1202

Brand: VBsemi
VBsemi VBQF1202 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1202 — Discrete & Power Semiconductors | Superb Automation

VBQF1202

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1202 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1202: 20 V and 2 milliohm in DFN 3 by 3, with a 100 A row and a 90 A package limit

The VBQF1202 is a 20 V N channel trench MOSFET in the DFN 3 by 3 body, and it is aimed squarely at OR-ing, server rails and DC to DC converters where the drain to source voltage is a 12 V bus with a small margin. The summary prints 20 V, 0.0020 ohm at 4.5 V, 0.0025 ohm at 2.5 V, 100 A continuous at a 25 C case, 95 A at 70 C and 86 nC of gate charge.

Two footnotes decide how the 100 A row should be read. One says the figure is calculated from the maximum junction temperature, and the other says the package limitation current is 90 A. The die can therefore pass what the lead frame cannot, and every current row above 90 A is arithmetic rather than a measurement.

A 20 V part at 2 milliohm is a conduction device rather than a switching device. At 40 A the loss is 3.2 W and at 90 A it is 16.2 W, so the whole question is how much copper sits under the pad. The gate charge of 171 nC typical and 257 nC maximum is large for a 3 by 3 body, which is the price of a die with 6500 pF of input capacitance.

The gate is the tightest rating on the sheet: plus or minus 12 V, against a 20 V class that often allows 20 V. A 12 V rail driving this gate directly sits on the limit, and a driver with any overshoot exceeds it. The recommended drive is 10 V or lower, and the leakage test is written at 20 V, which is above the absolute maximum, so that row describes the test bench rather than the application.

The parameter table in full

Drain to source voltage20 V
Gate to source voltage, continuousplus or minus 12 V
Continuous drain current, case at 25 C100 A calculated, 90 A package limited
Continuous drain current, case at 70 C95 A calculated
Continuous drain current, board at 25 C and 70 C35.8 A and 27 A
Pulsed drain current300 A
Avalanche current at 0.1 mH39 A
Single pulse avalanche energy94.8 mJ
Continuous diode current, case at 25 C90 A
Continuous diode current, board at 25 C3.13 A
Maximum power dissipation, case at 25 and 70 C250 and 175 W
Maximum power dissipation, board at 25 and 70 C3.75 and 2.63 W
Junction to ambient, 10 s, typical and maximum32 and 40 C per watt
Junction to ambient, steady state maximum90 C per watt
Junction to case, typical and maximum0.5 and 0.6 C per watt
Breakdown voltage temperature coefficient35 mV per C
Gate threshold temperature coefficientminus 7.5 mV per C
Gate threshold at 250 microamp0.5 V minimum, 1.0 V maximum
Gate leakage at 20 V100 nA maximum
Drain leakage at 20 V, 25 C and 55 C1 and 10 microamp
On state drain current at 10 V gate90 A minimum
On resistance at 4.5 V gate and 38.8 A0.0020 ohm typical
On resistance at 2.5 V gate and 37 A0.0025 ohm typical
Forward transconductance at 38.8 A160 S typical
Input, output and reverse transfer capacitance at 10 V6500, 1725 and 970 pF
Total gate charge at 10 V and at 4.5 V171 and 81.5 nC typical
Gate source and gate drain charge34 and 29 nC
Gate resistance at 1 MHz1.4 and 2.1 ohm
Turn on delay and rise time at 10 V drive18 and 11 ns typical
Turn off delay and fall time at 10 V drive70 and 10 ns typical
Turn on delay and rise time at 4.5 V drive55 and 180 ns typical
Body diode forward drop at 22 A0.8 V typical, 1.2 V maximum
Body diode recovery time52 ns typical, 60 maximum
Body diode recovery charge70.2 nC typical, 105 maximum
Reverse recovery fall and rise time27 and 25 ns
Operating junction and storage rangeminus 55 to plus 175 C

Two hundred and fifty watts on the case, three and three quarter on the board

The case row closes on the junction to case path. 250 W through 0.6 C per watt is 150 C of rise, which is exactly the 150 C between a 25 C case and the 175 C limit, and the typical 0.5 C per watt path leaves 125 C of rise and 25 C of margin. The row is therefore the thermal limit restated rather than an independent number.

On a board the allowance is 3.75 W through 32 C per watt, 120 C of rise and a 145 C junction in a 25 C room. Through 2 milliohm that is 43 A at the cold resistance and 32.7 A at a hot figure of 3.5 milliohm. The 35.8 A board row printed on the sheet matches that arithmetic closely, which makes the board rows the trustworthy ones on this part.

The diode current rows are the ones to read twice. Ninety amps with the case at 25 C is the same order as the channel rating, while the board row is 3.13 A. A synchronous rectifier that carries the load through the diode for a long dead time has 3 A of continuous capability, so the dead time has to be short and the body diode is for commutation only.

Ten volts against four and a half, and one row that is not this part

The two drive levels produce very different parts. At 10 V the gate charge is 171 nC and the rise time is 11 ns; at 4.5 V the charge falls to 81.5 nC but the rise time stretches to 180 ns, a factor of sixteen. A 4.5 V drive is enough to hold the part on and not enough to switch it quickly, so a high current stage driven from a 5 V rail will lose more in the crossover than it saves in gate drive.

The avalanche test stores less than the printed energy. Ninety four point eight millijoules is printed against a 0.1 mH coil at 39 A, and half of 0.1 mH times 1521 is 76 mJ. Here the printed figure exceeds what the stated test can store, which is the unsafe direction, so a 95 mJ transient is not demonstrated by this row. For an inductive load we work to 76 mJ.

The on resistance condition is mislabelled in the electrical table, which prints the 0.0020 ohm row at a 10 V gate while the product summary and the second row use 4.5 V and 2.5 V. A 12 V maximum gate cannot support a 10 V specification point on a 20 V part in a 3 by 3 body without a separate gate drive, and the summary is the row that matches the threshold window of 0.5 V to 1.0 V.

The gate leakage test at 20 V is above the plus or minus 12 V absolute maximum, so the 100 nA row is a bench measurement that cannot occur in a working circuit. It tells you the oxide is good and nothing about the application.

Where a 20 V, 2 milliohm part earns its place

A 12 V to 1 V multiphase converter with 40 A per phase, an OR-ing switch on a 12 V redundant bus, a battery disconnect on a two cell pack and a hot swap switch on a 12 V backplane all fit. The 20 V rating suits a 12 V rail with 8 V of headroom for the switching spike, and the 2 milliohm resistance keeps the conduction loss near 3 W at 40 A.

It does not fit a 12 V rail with a long trace and a hard switching edge, where the spike exceeds 20 V, and it does not fit a fanless board above 30 A or a synchronous rectifier with a long dead time. A 30 V part or a two device parallel arrangement is the answer in those cases.

Our power management cross reference work keeps the board thermal row, the diode board current and the gate charge at the intended drive level per approved alternate, because a 20 V part with a 12 V gate limit, a 3 A diode and 257 nC of gate charge is a specific component, and a substitute that matches only voltage and resistance will change both the drive and the dead time.

Questions we answer before a reel is booked

First, the gate rail. The part is rated to plus or minus 12 V, so a 12 V driver sits on the limit and any overshoot exceeds it. A 10 V rail with a 2 ohm resistor gives 171 nC in 17 ns and keeps the gate inside the rating, and the 2.1 ohm maximum internal resistance is a small part of that.

Second, the package limit. The 100 A row is calculated while the lead frame stops at 90 A, and the board row stops near 35 A. We ask for the continuous current and the copper area rather than the headline, because a 3 by 3 body at 40 A is already at the board allowance.

Third, the alternate. A 20 V part at 1.8 to 2.5 milliohm in a 3 by 3 body comes with gate charges from 80 to 260 nC and diode board currents from 1 to 10 A. We hold those rows per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the 3 by 3 land pattern, the pad size and the pin order, since the pad is what carries 30 A in this body.