Contact Us

VBGM1102

Brand: VBsemi
VBsemi VBGM1102 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGM1102 — Discrete & Power Semiconductors | Superb Automation

VBGM1102

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGM1102 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGM1102: 100 V and 180 A in a TO220

The VBGM1102 is a single N channel MOSFET rated at 100 V drain to source, with a plus or minus 20 V gate window and a threshold of 3 V. It carries 180 A and its on resistance is 2.4 milliohm at a 10 V gate. The silicon is a shielded gate structure and the body is the TO220 through hole package.

A 2.4 milliohm, 100 V die is a serious piece of silicon. At 40 A it drops 96 millivolt and dissipates 3.8 watt; at 100 A it dissipates 24 watt, which is more than a TO220 tab can shed without a heatsink. So the part is a high current switch that lives on a heatsink, in a battery disconnect, a motor drive, a welding supply or an inverter stage.

The 100 V rating is the interesting constraint. It sits above a 72 V battery pack with 39 per cent of margin, above a 48 V rail with 108 per cent, and it is the voltage class that a 60 V part cannot reach when the pack is at full charge and the switch turns off into an inductive load.

Key data for the VBGM1102

ConfigurationSingle N channel
PackageTO220, three lead through hole with tab
VDS100 V
VGSPlus or minus 20 V
Vth3 V typical
ID180 A, a die limit at a 25 C case
RDS(on) at 10 V2.4 milliohm
TechnologyShielded gate trench
Gate chargeNot published on the catalogue page, request the data sheet for a switching budget
Body diodeIntrinsic, and at this die size its recovery is a real loss in a bridge
Drive10 V or more, from a driver with amp level peak current
Thermal pathTab to heatsink, isolated or live depending on the mounting kit

Shielded gate silicon and the numbers it moves

A shielded gate structure puts a field plate under the gate, which lets the epitaxial layer be doped more heavily for the same breakdown voltage. The result is a resistance per unit area that a planar part cannot reach at 100 V, which is how 2.4 milliohm appears in a body that would have held 10 milliohm a decade ago.

The cost is a gate charge that is not small. A die this size has a lot of gate area, and the charge scales with it. Driving 2.4 milliohm of silicon from a microcontroller pin produces a turn on edge measured in microseconds, and at any real switching frequency that edge is where most of the loss sits. A dedicated driver with a peak current of several amps is the normal pairing, and the gate resistor is chosen to trade ringing against speed rather than copied from a smaller part.

The 3 V threshold is also higher than the logic level parts in this catalogue. A 5 V drive gives 2 V of overdrive, which is workable but not generous. The 10 V column is where the 2.4 milliohm figure lives, and a board that drives the gate at 5 V should expect a resistance well above it.

180 A, 2.4 milliohm, and the heat that comes with both

The two numbers together define the thermal problem. At 180 A the conduction loss is 78 watt, which is a die limit and nothing else. At 60 A it is 8.6 watt, which a TO220 on a 2 degree per watt heatsink handles with the junction 17 degrees above the case. At 30 A it is 2.2 watt and the tab is comfortable without a heatsink.

So the working current for this package is somewhere between 30 and 60 A depending on the heatsink, and the 180 A headline describes what the die can pass in a pulse. That gap is not a vendor trick, it is the same gap that exists on every power device, and it is the reason a thermal calculation has to be done before a part is chosen rather than after.

The body diode deserves a separate note. In a motor bridge the diode carries the freewheel current for part of every cycle. At 60 A the diode forward drop is around a volt, which is 60 watt during the freewheel interval. A part chosen for its channel resistance can still overheat because of its diode, and the fix is either a shorter freewheel interval, a parallel Schottky, or a different topology.

When a 100 V part is the right answer and when it is not

On a 48 V rail a 100 V part gives 108 per cent of margin, which is more than needed and costs resistance compared with a 60 V device of the same die area. On a 72 V pack it is the right class, because the pack at full charge plus the turn off overshoot lands near 90 V and a 60 V part would be outside its rating every cycle.

The decision is made by the highest voltage the drain ever sees, not by the nominal rail. Our component lead time solutions page covers how a programme that needs a specific voltage class is kept supplied when the market for that class tightens, which is what tends to happen first in the high current cells.

A second question is whether the extra voltage class is worth the resistance. At the same die area a 100 V part has roughly twice the resistance of a 60 V part, so a 60 V part of the same size would be near 1.2 milliohm. If the rail allows 60 V, the 60 V part is the better switch, and the 100 V part is chosen for margin rather than for performance.

The sourcing side of this part is covered on the supplier scorecard. For a high current die that only a few sources can make, that page covers how a source is scored across a programme.

Questions we get on this code

Can 180 A be run continuously? No. The continuous current is set by the heatsink. With a 2 degree per watt sink the practical figure is around 50 to 60 A, and without a sink it is nearer 25 to 30 A.

Is a 5 V gate drive enough? It will switch, but the 2.4 milliohm figure is a 10 V number. At 5 V with a 3 V threshold the resistance is not published and is likely to be two to three times higher, which changes the thermal sum.

What package options exist for the same die? The catalogue lists this code in TO220. Equivalent silicon in a TO247 or a TOLL body appears under other codes in the same family, and moving to one of those is a board change rather than a substitution.

How is it packed? Through hole power bodies normally ship in tubes. We confirm the tube count and the date code on the quotation.