VBQF1154N
Product Specifications
VBQF1154N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF1154N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF1154N: a 150 V N channel in the 3 by 3 body
The VBQF1154N is a single N channel MOSFET in the DFN8 3 by 3 body at 150 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 25.5 A of drain current and 35 milliohm at a 10 V gate. Like the 100 V part in the same family it carries no published 4.5 V figure, and here that matters more because the threshold is 3 V rather than 1.8 V.
A 3 V threshold on a 150 V part is the normal value for this voltage class. The gate has to reach 8 to 10 V to get the published resistance, and a 5 V drive leaves the part only 2 V above threshold, which is barely on. This is a part for a 10 V or a 12 V drive, not for a logic level circuit.
One hundred and fifty volts covers a 96 V battery string, a 110 V DC bus and a 120 V rail with a clamp. Those are the three lines where this part appears, and in all three the alternative is a 200 V part at roughly twice the resistance in the same body.
Key data for the VBQF1154N
| Configuration | Single N channel |
| Package | DFN8 3 by 3, exposed pad |
| VDS | 150 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 25.5 A at a 25 C case |
| RDS(on) at 10 V | 35 milliohm |
| RDS(on) at 4.5 V | Not published by the vendor |
| Structure | Trench |
| Conduction at 3 A | 0.32 W |
| Conduction at 5 A | 0.88 W |
| Conduction at 8 A | 2.24 W |
| Conduction at 15 A | 7.9 W |
A 150 V part on a motor or a relay load sees avalanche energy if the freewheel path is slow. The vendor page gives no avalanche rating, so the circuit has to keep the drain below 150 V by clamping rather than by relying on the die to absorb energy. A transient suppression diode across the switch, or a freewheel diode across the load, is what holds the peak; a part without a published avalanche rating should not be the clamp itself.
Where a 150 V part is used
The first case is a 96 V battery string on a light electric vehicle or a storage module. The pack reaches 109 V at full charge, the switch has to hold the pack plus the motor's leakage spike, and the clamp is set at 130 V. A 150 V part holds that with a margin of 1.15, which is enough on a controlled board arrangement and not enough on a long motor cable without a snubber.
The second case is a 110 V DC bus in an industrial drive or a telecom rectifier output. Those rails are steady with a modest transient, so the 150 V rating is comfortable and the choice is really about the resistance: 35 milliohm at 5 A is 0.88 W, which the 3 by 3 handles.
The third case is a flyback primary on a 90 to 130 V input, where the reflected voltage plus the leakage spike has to stay under the rating. That is a calculation, not a guess: the turns ratio, the clamp and the leakage inductance all move the peak.
The threshold and the drive
With a 3 V threshold the part needs a gate at 10 V to reach 35 milliohm. A 12 V driver is comfortable, an 8 V driver is marginal, and a 5 V driver puts the part in the linear region where the resistance is several times higher and the loss does not match the table.
The gate charge of a 150 V trench part is not small, and at 100 kHz the drive current becomes part of the budget. A 10 to 22 ohm gate resistor and a driver that can source and sink an amp are the usual combination. Undervoltage lockout in the driver matters here: a partially enhanced 150 V part can fail in a few microseconds under load.
Thermal behaviour, and the package limit
At 5 A the loss is 0.88 W, at 8 A it is 2.24 W and at 15 A it is 7.9 W from 35 milliohm. A 3 by 3 pad on four square centimetres of copper is 35 to 45 K per watt, so 8 A is a 78 to 100 K rise and 15 A is closer to 280 to 355 K. In still air the continuous current is 6 to 8 A.
The 25.5 A on the data page is a die figure at a 25 C case. Reaching it needs the pad held at 25 C by a heatsink or a metal core board, which is not what a 3 by 3 land pattern does on FR-4. A buyer who needs 25 A continuously at 150 V should be looking at a 5 by 6 body or a TO-252, not at this part.
Where a substitute is being proved in a board that was qualified on another 150 V code, the how to verify a drop in replacement page covers the bench checks before the change is signed off, from threshold and gate charge to the reverse recovery of the body diode.
The step from 150 V to 200 V costs about 60 per cent more resistance in the same body, because the drift region grows faster than the voltage at this level. A 150 V part at 35 milliohm and a 200 V part at 55 to 60 milliohm share the same package and the same pad, so the choice is made on the clamp voltage of the line: a 96 V pack with a 130 V clamp fits the 150 V part with a margin of 1.15, while a 110 V bus with a 150 V clamp fits neither and needs 200 V.
The gate of a 150 V part has to be driven from a supply that is present before the drain voltage arrives. A driver with undervoltage lockout holds the part off until its own rail is above threshold, which prevents the case where a partly enhanced 150 V part sits in the linear region with the full pack voltage across it. That case fails on the bench in a few microseconds and looks like a shorted gate in the failure report. A resistor from gate to source, 10 to 100 k, keeps the part off if the driver is unpowered.
The gate charge of a 150 V part at this current class is roughly 20 to 40 nC. At 100 kHz that is 2 to 4 mA of average drive current, which any driver can supply, so the drive budget is set by the peak current during the switching transition rather than by the average. A 10 ohm gate resistor with a 12 V drive gives about 1.2 A of peak, which turns the part on in 20 to 30 ns and keeps the transition inside the safe area for the frequency this part is used at.
The sourcing side of this part is covered on the supplier quality audit. For a 150 V code on a qualified board, that page covers what is checked at the source before a new lot is released.
Questions we get on this code
Will it work on a 5 V gate drive? It will turn on but not reach 35 milliohm. With a 3 V threshold there is only 2 V of overdrive at 5 V, and the loss will be two to three times the table figure.
Is 150 V enough for a 96 V pack? At 109 V full charge plus a clamped spike at 130 V, yes. Without a clamp the peak is set by the board parasitics and can exceed the rating.
Can two be paralleled for 16 A? Yes with a gate resistor on each and a symmetrical board arrangement. The 3 by 3 pad is the limit, so two pads are worth more than one bigger part here.
Does the vendor publish a switching safe area curve? The product page carries the parameter table only. For an inrush or a linear mode event, the full datasheet has to be requested before the part is released.