VBQF1101N
Product Specifications
VBQF1101N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQF1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQF1101N: 100 V and 10 milliohm in DFN 3 by 3, built for a slow switching primary
The VBQF1101N is a 100 V N channel trench MOSFET in the DFN 3 by 3 body with an exposed pad. The summary prints 100 V, 0.010 ohm at a 10 V gate, 50 A continuous at a 25 C case and a 175 C junction, and the application list is a single item, isolated DC to DC converters, which is where a 100 V part in a small body belongs.
What separates this sheet from the other 100 V parts in the same band is the switching table. Rise time is 220 ns typical and fall time is 200 ns typical at 58 A into a 1.5 ohm load with a 2.5 ohm gate resistor, which is two orders of magnitude slower than the 100 V parts with 10 ns edges. The gate charge of 90 nC typical and 130 nC maximum explains it: a 100 V die with 3200 pF of input capacitance and a 3.1 ohm maximum gate resistance cannot be switched quickly by a small driver.
The on resistance is printed at three temperatures, 10 milliohm at 25 C, 13 at 125 C and 27 at 175 C, so the loss at a given current more than doubles across the range. At 30 A the 25 C figure is 9 W and the 175 C figure is 24.3 W, which is the number to use in a sealed enclosure.
The dissipation rows are split between a 355 W case figure and a 3.35 W ambient figure, a hundred to one ratio that tells the reader the part is meant to be bolted to copper or not used at high current at all. The 40 C per watt junction to ambient row is the one that governs a board mounted converter.
The parameter table in full
| Drain to source voltage | 100 V |
| Gate to source voltage, continuous | plus or minus 20 V |
| Continuous drain current, case at 25 C | 50 A |
| Continuous drain current, case at 125 C | 45 A |
| Pulsed drain current | 60 A |
| Avalanche current at 0.1 mH | 51 A |
| Single pulse avalanche energy at 1 per cent duty | 60 mJ |
| Maximum power dissipation, case at 25 C | 355 W |
| Maximum power dissipation, board at 25 C | 3.35 W |
| Junction to ambient, board mounted on 1 inch FR4 | 40 C per watt |
| Junction to case | 0.4 C per watt |
| Breakdown voltage at 250 microamp | 100 V |
| Gate threshold at 250 microamp | 2 V minimum, 4 V maximum |
| Gate body leakage at 20 V | 100 nA maximum |
| Drain leakage at 100 V, 25 C, 125 C and 175 C | 1, 50 and 250 microamp |
| On state drain current at 10 V gate | 120 A minimum |
| On resistance at 10 V gate and 30 A, 25 C | 0.010 ohm typical |
| On resistance at 10 V gate and 30 A, 125 C | 0.013 ohm typical |
| On resistance at 10 V gate and 30 A, 175 C | 0.027 ohm typical |
| Forward transconductance at 30 A | 25 S minimum |
| Input, output and reverse transfer capacitance at 25 V | 3200, 410 and 210 pF |
| Total gate charge at 10 V, 100 V and 58 A | 90 nC typical, 130 nC maximum |
| Gate source and gate drain charge | 23 and 34 nC |
| Gate resistance | 0.5, 1.3 and 3.1 ohm |
| Turn on delay and rise time at 58 A and 2.5 ohm | 24 and 220 ns typical |
| Turn off delay and fall time, same conditions | 45 and 200 ns typical |
| Continuous source drain diode current | 58 A |
| Pulsed diode current | 110 A |
| Body diode forward drop at 58 A | 1.0 V typical, 1.5 V maximum |
| Body diode recovery time | 130 ns typical, 200 maximum |
| Body diode recovery charge | 0.52 microcoulomb typical, 1.2 maximum |
| Peak reverse recovery current | 8 A typical, 12 maximum |
| Operating junction and storage range | minus 55 to plus 175 C |
Three hundred and fifty five watts on the case, three and a third on the board
The case row is consistent with the junction to case path. 355 W through 0.4 C per watt is 142 C of rise, which lands on a 167 C junction from a 25 C case and leaves 8 C inside the 175 C limit. The 355 W is therefore a genuine die capability, provided the case is held at 25 C with a heatsink and a thermal interface.
The board row is the one that applies to a converter. 3.35 W through 40 C per watt is 134 C of rise, which puts the junction at 159 C in a 25 C room and at the limit in a 45 C room. Through 10 milliohm that is 18.3 A at the cold resistance and 15.8 A at the 125 C figure, which is a third of the 50 A headline. A 50 A converter built on this part needs a copper plane that changes the 40 C per watt row into something closer to the 20 C per watt of a larger body.
The 120 A on state current row is the third figure to hold in mind. It is a pulse measurement at a 5 V drain and a 10 V gate, and it describes what the die can pass for 300 microseconds rather than any continuous capability. It is useful for inrush and useless for thermal work.
Where this sheet argues with itself
The avalanche row is conservative in the safe direction. Sixty millijoules is printed against a 0.1 mH coil at a 51 A avalanche current, and half of 0.1 mH times 2601 is 130 mJ stored. The part is credited with less than half of what the test delivers, so a 60 mJ clamp is genuinely inside the rating.
The recovery rows do not agree with each other. A recovery charge of 0.52 microcoulomb against a 130 ns recovery time implies 4 A of average reverse current, and the peak reverse current row prints 8 A typical, so the charge is consistent with a triangular pulse of about 8 A over 130 ns. That is the one place in this shipment where the charge, the time and the peak current all close, and it makes the 200 ns maximum figure usable for a snubber calculation.
The drain leakage rows are specified at 125 C and 175 C, which is a hotter test than most sheets in this band, and the 250 microamp at 175 C is ten times the 25 C value. In a converter that runs its die above 150 C the leakage is a real part of the loss budget rather than a footnote.
Where a 100 V, 10 milliohm, slow part earns its place
A 48 V to 12 V converter running below 30 kHz, a primary side switch in a flyback with a snubber, a battery disconnect and an OR-ing switch on a 48 V rail all fit. The slow edge is an advantage in the first two, because a 220 ns rise into a transformer limits the leakage spike without a large snubber.
It is the wrong part for a hard switched converter above 50 kHz. At 100 kHz with 100 V and 50 A, a 200 ns fall time is a crossover loss of about 50 W, against 25 W of conduction at 10 milliohm, so the switching loss dominates and the part loses to any device with a 20 ns edge. Above 50 kHz the same die with a proper driver and a smaller gate resistor is the only way to use it, and the 3.1 ohm maximum gate resistance limits how far that can go.
Our power management cross reference work keeps the rise and fall times and the gate resistance spread per approved alternate, because at this current level the switching loss and the conduction loss are the same size, and a cross reference that checks only on resistance will move the efficiency by several points.
Questions we answer before a reel is booked
First, the frequency. The 220 ns rise and 200 ns fall times set a ceiling near 30 kHz for a hard switched stage, and a resonant or soft switched stage removes the ceiling. We ask for the topology before approving the part, because the same die is excellent in one and unusable in the other.
Second, the driver. 130 nC maximum at 0.3 A is 433 ns of gate charge time, which is longer than the 200 ns fall time and means a small driver, not the MOSFET, sets the edge. A 1 A driver with a 4.7 ohm resistor brings the edge to the die limit, and the 3.1 ohm internal resistance then becomes the floor.
Third, the alternate. A 100 V part at 8 to 12 milliohm in a 3 by 3 body comes with fall times from 10 to 250 ns and gate charges from 20 to 130 nC, so two parts that look identical on a summary page behave as different components in a converter. We hold the switching rows per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the 3 by 3 land pattern and the exposed pad size rather than from the current rating.