Contact Us

VBQA2412

Brand: VBsemi
VBsemi VBQA2412 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2412 — Discrete & Power Semiconductors | Superb Automation

VBQA2412

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2412 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2412: a minus 40 V P channel, 10 milliohm at a 10 V gate

The VBQA2412 is the 40 V member of the same 5 by 6 P channel family, with minus 40 V drain to source, plus or minus 20 V on the gate, a minus 2 V threshold, minus 40 A of drain current, 12 milliohm at a 4.5 V gate and 10 milliohm at a 10 V gate. It is the part chosen when a 24 V rail has to survive a load dump clamp or when a 12 V rail is fed from a source that can jump to 36 V.

The step from 30 V to 40 V costs very little in this body, 8 milliohm to 10 milliohm, because the drift region only grows by a third at this voltage. That is the cheapest 10 V of margin in the whole MOSFET range, and it is why 40 V parts are the default for anything fed from a vehicle or from a 24 V industrial supply.

The threshold is minus 2 V rather than minus 2.5 V, so the part starts to conduct earlier and can be used with a lower drive, at the cost of a slightly higher leakage in the off state at high temperature. For a load switch that is a fair trade; for a part that sits across a battery for years it is worth checking the leakage budget.

Key data for the VBQA2412

ConfigurationSingle P channel
PackageDFN8 5 by 6, exposed pad
VDSMinus 40 V
VGSPlus or minus 20 V
VthMinus 2 V typical
IDMinus 40 A, a die figure at a 25 C case
RDS(on) at 4.5 V12 milliohm
RDS(on) at 10 V10 milliohm
StructureTrench
Conduction at 5 A0.25 W
Conduction at 10 A1 W
Conduction at 20 A4 W
Conduction at 40 A16 W

A load dump is an energy event rather than a voltage event. The clamp holds the line at 35 V, the alternator current flows into the clamp and the wiring inductance, and the pulse lasts 100 to 400 ms. During that time the part holds 35 V across it with the gate off, so it is a leakage event rather than a conduction event, and the die heats by the leakage times the voltage. For a 5 by 6 die that is a few watts at the top of the temperature range, which the pad carries for the length of the pulse. The number to check is the junction temperature at the end of the pulse, not the headline voltage rating.

Where a 40 V P channel is used

The vehicle case is the clearest. A 12 V system has a 35 V load dump clamp in the unclamped case and a 27 V clamp in the centralised case, and a 40 V part sits above both. The gate drive has to be protected as well, because the gate is referenced to a source that moves with the battery, so a zener and a series resistor are always present on these circuits.

The 24 V industrial case is similar but the numbers are tighter. A 24 V supply with a 10 per cent tolerance is 26.4 V, a 33 V TVS clamps transients at 33 to 36 V, and a 40 V part holds a margin of only 1.1 against the clamp. On a line with long inductive runs, a 60 V part is the safer choice, which is what the VBQA2658 in this band is for.

The third case is a battery disconnect with a pre charge path. The P channel sits in the positive line, the load capacitance is charged through a resistor first, and the switch closes after the rail is within a volt of the battery. At 10 milliohm the part carries 10 A with 1 W of loss, which a 5 by 6 pad handles in still air.

Comparing it with the parts either side

Against the VBQA2311, the 40 V part gives 10 V more headroom for 2 milliohm more resistance at the same gate voltage. On a 24 V rail that trade is almost always worth taking, and on a 12 V rail with a clean supply it is not needed. Against the VBQA2658, the 60 V part, the resistance roughly quintuples to 50 milliohm, which is the real cost of another 20 V of rating at this current class.

That progression, 8, 10 and 50 milliohm for 30, 40 and 60 V, is normal for trench P channel silicon. The drift region resistance grows with the square of the voltage while the channel resistance stays the same, so the resistance is dominated by the channel up to about 40 V and by the drift region above it. A 60 V P channel is a different economic proposition from a 40 V one, and the choice of rating should be made on the clamp voltage of the line rather than on a round number.

Losses and switching

At 10 A and 10 milliohm the conduction loss is 1 W, at 20 A it is 4 W and at 40 A it is 16 W. Hot, the resistance rises by about 40 per cent, so the 20 A figure becomes 5.6 W. A 5 by 6 pad on four square centimetres of copper is around 25 to 30 K per watt, which puts 20 A at a 140 to 170 K rise, so the usable continuous current is 10 to 12 A.

The part is a switch, not a converter device. The gate charge is large for a P channel of this size and the only pull up is a resistor to the source, so the turn off is set by that resistor and the gate capacitance, and it lands in the tens of microseconds. It is fast enough for a load switch and for a reverse protection path, and far too slow for a switching regulator.

Where a part has to be substituted because the original code has gone short lead, the how to verify a drop in replacement page covers the bench checks, from threshold and gate charge to the body diode direction, that decide whether the substitute behaves the same in the circuit.

The 5 by 6 land pattern is the same across this family, which is the practical reason to stay inside it. The pad carries the drain, so the copper under the part sits at the load voltage when the switch is off, and a pour that spreads from that pad towards a low voltage signal has to be kept clear. Six vias of 0.3 mm inside the pad into an inner plane take the thermal resistance from about 30 K per watt to nearer 20, and on a two layer board with no plane the figure is closer to 55, which is the difference between 12 A and 7 A of continuous current.

The sourcing side of this part is covered on the pin to pin cross reference. For a 40 V P channel in a board that was qualified on another code, that page covers which parameters have to match before the swap.

Questions we get on this code

Is it automotive qualified? The vendor page carries electrical numbers only and no AEC-Q101 statement, so it should be treated as an industrial part until a qualification document is produced.

Can it survive a 35 V load dump? At 40 V rated, yes on a clamped system. On an unclamped system the pulse also heats the die, and the energy has to be checked rather than the voltage alone.

Why is the 4.5 V figure 20 per cent worse than the 10 V figure? Because the channel is not fully enhanced at 4.5 V. The gap is smaller here than on the 30 V part because the threshold is lower.

Does the body diode conduct in normal operation? Only during the reverse polarity event or when the load is charged before the switch closes. In the on state the channel carries the current and the diode is bypassed by 10 milliohm.