Contact Us

VBQF2309

Brand: VBsemi
VBsemi VBQF2309 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF2309 — Discrete & Power Semiconductors | Superb Automation

VBQF2309

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF2309 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF2309: a 30 V P channel in a 3 by 3 DFN

The VBQF2309 is a single P channel in a DFN8 measuring 3 by 3 millimetres, with the drain on the bottom pad. It is rated at minus 30 V, carries minus 45 A, and prints 18 milliohm at a 4.5 V gate against 11 milliohm at 10 V. The threshold is minus 2.5 V and the gate window is plus or minus 20 V.

A P channel at 30 V with 11 milliohm is the high side switch for a 12 V or a 24 V rail without a charge pump. Pulling the gate to ground turns it on, and the source sits on the rail. For a load that has to be switched from a microcontroller pin through a small N channel, this is the shortest circuit path there is.

The bottom side drain pad is also the thermal path. Unlike the SC70 parts, this package can carry real current, and the 45 A headline starts to become usable once the pad gets a proper via array. It is still not a continuous figure, but it is far closer than a three lead package.

Key data for the VBQF2309

ConfigurationSingle P channel
PackageDFN8, 3.0 mm by 3.0 mm, bottom side drain pad
VDSMinus 30 V
VGSPlus or minus 20 V
VthMinus 2.5 V
IDMinus 45 A at 25 C case
RDS(on) at 4.5 V18 milliohm
RDS(on) at 10 V11 milliohm
TechnologyTrench
Gate drivePull gate to ground through a resistor to conduct
Body diodeAnode at the drain, blocks in the reverse direction
Thermal pathBottom pad to copper, vias carry current and heat

A minus 2.5 V threshold and a 12 V rail

With a threshold of minus 2.5 V, a gate held at 1.5 V below the source is not enough to turn the part off, and the leakage in that state is the one to check on a battery product. The gate has to be pulled to the source rail when the switch is off, and the pull up resistor has to be low enough that the threshold spread does not open the part at 85 C.

On a 12 V rail the gate to source voltage in the off state is the full 12 V, which is inside the 20 V window but leaves 8 V for ringing. A 12 V rail with a hot plug event can ring well past that. A gate to source zener of 15 V, or a series gate resistor with a clamp, is cheap insurance.

At 4.5 V of gate drive the part is at 18 milliohm, and at 10 V at 11. For a 10 A load the difference is 0.7 watt against 1.1 watt, which decides whether a 3 by 3 package needs airflow. A driver that reaches 10 V is worth the extra component on any load above 8 A.

Reverse polarity and inrush in one part

A P channel in the positive lead with its gate pulled to ground gives a reverse polarity block, and this package can carry a real load. The two failure modes are gate overvoltage on a reversed battery and inrush at plug in. On a 24 V rail a reversed battery puts 24 V across the gate oxide in the wrong polarity, which exceeds the 20 V window, so a gate clamp is required rather than optional.

Inrush is the second issue. The part turns on over the miller plateau and the load capacitance charges through the channel while it is still in the linear region. For a 1000 microfarad load the peak dissipation can be tens of watts for a few hundred microseconds. The data sheet publishes a safe operating area curve for exactly this; ask for it before a hot plug application is signed off.

Where this part fits

A 12 V or a 24 V load switch on a vehicle accessory, a battery disconnect on a two or three cell pack, a reverse polarity block on an industrial input, and a high side switch in a motor drive up to 10 A are all in range.

For a power switch that has to stay available over a long programme, the power management cross reference page covers which parameters have to match before a substitute is accepted.

The sourcing side of this part is covered on the supplier scorecard. For a load switch that carries the whole product current, that page covers how a source is scored across a programme.

Questions we get on this code

Can the gate be driven from a 3.3 V pin? Only through a small N channel or a level shifter. The gate has to go below the source by several volts; a 3.3 V pin cannot pull a 12 V rail down on its own.

Is 45 A continuous? No. With a good pad and vias, 15 to 20 A continuous is realistic in still air, more with airflow. The 45 A is a package limit at 25 C case.

What is the gate charge? Not printed on the catalogue page. For a 3 by 3 package at this current it is on the order of tens of nanocoulombs; ask for the number before sizing the pull up resistor and the switching speed.

Does the body diode conduct when the load is inductive? Yes, from load to rail. Its forward drop is about 0.8 V, so a 10 A freewheel is 8 watt for the duration of the interval. Add an external diode if the interval is long.