Contact Us

VBP1103

Brand: VBsemi
VBsemi VBP1103 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP1103 — Discrete & Power Semiconductors | Superb Automation

VBP1103

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP1103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP1103: a 100 V, 320 A N channel in a TO247

The VBP1103 is a single N channel in a TO247, the package with a metal tab and a screw hole. It is rated at 100 V, prints 2 milliohm at a 10 V gate and 320 A of drain current. The threshold is 3 V and the gate window is plus or minus 20 V. The die is a trench part aimed at high current conduction rather than at fast switching.

Two milliohm is the number that decides the application. At 50 A a 2 milliohm device burns 5 watt, which a TO247 on a heatsink can hold. At 100 A it burns 20 watt, which needs a serious heatsink and a fan. The 320 A figure is the bond wire and clip limit at a case temperature of 25 C, and it is not a continuous rating for a real product.

The TO247 form factor is what makes this class practical: the tab is isolated from the die, so the part can be screwed to a shared heatsink with an insulating pad, and the leads take a solder joint that survives thermal cycling.

Key data for the VBP1103

ConfigurationSingle N channel
PackageTO247, metal tab with screw hole
VDS100 V
VGSPlus or minus 20 V
Vth3 V
ID320 A at 25 C case, a package and bond limit
RDS(on) at 10 V2 milliohm
RDS(on) at 4.5 VNot printed, use a 10 V driver for this device
TechnologyTrench
MountingScrew to heatsink, insulating pad and bush for a shared sink
Gate drive10 V for the printed on resistance
Typical useBattery disconnect, inverter leg, high current load switch

Why a 100 V part at this current is a different animal

A 100 V trench device with 2 milliohm has a very large die. The gate charge that comes with that area is large too, so the drive has to supply real current: a 100 nC gate charge switched at 20 kHz is 2 milliamps of average gate current, and the peak during the switching edge is amps. A weak driver will spend a long time in the linear region and cook the part.

The 3 V threshold sets the drive requirement. A 4.5 V gate leaves only 1.5 V of overdrive, which is not where a 320 A device should operate. Use a dedicated gate driver with a 10 V or 12 V output and a gate resistor sized to keep the switching edge under a microsecond without ringing.

The 100 V rating gives 40 V of headroom over a 60 V nominal rail and about 20 V over an 80 V rail. For a 48 V system it is generous, and the low on resistance is the reason to accept the larger die: at 100 A the loss is 20 watt rather than the 100 watt a 20 milliohm part would burn.

Thermal arithmetic on a TO247

The junction to case resistance of a TO247 is about 0.3 to 0.5 degrees per watt. With an insulating pad the case to sink path adds 0.5 to 1.0, and a modest heatsink adds 2 to 5 to ambient. Taking 4 degrees per watt end to end, a 20 watt loss raises the junction 80 degrees above ambient, which from a 40 C ambient puts it at 120 C, just inside a 150 C limit.

That is the whole story of this part: at 100 A it is a heatsink problem, at 50 A it is comfortable, at 20 A it is barely warm. The current a customer can use is set by the cooling they are prepared to pay for, not by the 320 A on the front page.

Screw torque matters. A loose screw on a TO247 raises the case to sink resistance by a factor of three, and the part fails a year later in the field. The datasheet torque figure is not a suggestion.

Where a 100 V TO247 is the right choice

Battery disconnect on a 72 V or 96 V pack, the low side of an inverter leg in a motor drive up to a few kilowatts, a high current DC load switch on a test rack, and the input protection of a high power charger are all inside the window.

For a part that is bought in tens or hundreds per build and where a second source may be needed later, the power management cross reference page covers what has to match before a substitute is accepted on a high current path.

The sourcing side of this part is covered on the component lead time solutions. For a high current device that a programme has to hold for years, that page covers how buffer is sized and what is confirmed before a date is promised.

Questions we get on this code

Is 320 A available continuously? No. It is a package and bond limit at 25 C case. Continuous current is set by the heatsink: about 100 A with a good forced air sink, 50 A with a modest one.

Can several of these be paralleled? Yes, and at this current level paralleling is normal. Match the gate resistors, give each device its own source connection to the common node, and accept that the threshold spread will put most of the current in one device at low currents.

Can it be driven from a microcontroller pin? No. The gate charge is too large. Use a gate driver with at least 1 A of peak output and a 10 V to 12 V rail.

What is the avalanche rating? The catalogue page does not print it. For a load with real inductive energy ask for the data sheet single pulse curve, because a 100 V part in a motor circuit will see avalanche events at turn off.