Contact Us

VBQA2311

Brand: VBsemi
VBsemi VBQA2311 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2311 — Discrete & Power Semiconductors | Superb Automation

VBQA2311

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2311 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2311: a minus 30 V P channel in a DFN 5 by 6

The VBQA2311 is a single P channel MOSFET in the DFN8 5 by 6 body, printed at minus 30 V drain to source, plus or minus 20 V on the gate, a minus 2.5 V threshold, minus 35 A of drain current, 16 milliohm at a 4.5 V gate and 8 milliohm at a 10 V gate. The die is trench. It sits at the bottom of the P channel ladder in this band, which is where the high side switch of a 12 V or a 24 V rail lives.

Thirty volts is the right rating for a 12 V rail with load dump or a 24 V rail with a transient clamp. A 12 V battery line sits at 14.4 V in charge and can reach 18 to 20 V during a jump start, and a 24 V truck line sits at 28.8 V in charge. Both stay under 30 V steady state, and the clamp on the input takes the rest. A 30 V part also keeps the on resistance low, because the drift region is short, which is why 8 milliohm is available in a 5 by 6 body at all.

The cost of a P channel is silicon area, since hole mobility is about a third of electron mobility, so the same resistance needs roughly three times the die. At 30 V that penalty is affordable. At 200 V it is not, which is why the high side of a high voltage bus is normally an N channel with a charge pump.

Key data for the VBQA2311

ConfigurationSingle P channel
PackageDFN8 5 by 6, exposed pad
VDSMinus 30 V
VGSPlus or minus 20 V
VthMinus 2.5 V typical
IDMinus 35 A, a die figure at a 25 C case
RDS(on) at 4.5 V16 milliohm
RDS(on) at 10 V8 milliohm
StructureTrench
Conduction at 5 A0.2 W
Conduction at 10 A0.8 W
Conduction at 20 A3.2 W
Conduction at 35 A9.8 W

Read together, the four numbers describe a part that is fully enhanced at a 10 V gate, partly enhanced at 4.5 V and off once the gate rises to within 2.5 V of the source. The 8 milliohm figure belongs to the first case and 16 milliohm to the second. Anything that applies a drive slower than 5 V below the source is outside the published data and has to be characterised on the bench. The off state is the other end of the same curve: at 125 C the leakage with the gate held at the source is in the microamp range for a die this size, which over a year is a few tens of milliamp hours out of a battery, and it is worth checking on a standby load that has to hold for months.

Where a 30 V P channel is used

The first case is a load switch in the positive line of a 12 V rail. The source goes to the rail, the drain goes to the load, and a resistor from gate to source holds the part off until a small NPN or an open drain output pulls the gate down. The load sees the rail with 8 milliohm in series, which at 5 A is 40 mV of drop. Nothing else in the path is that clean.

The second case is reverse polarity protection on a battery input. An N channel in the return line is cheaper, but the return line is often shared with a chassis ground, and then the switch has to sit in the positive line. A P channel with the drain towards the battery and the source towards the load conducts through its body diode when the battery is fitted the right way round, and blocks when it is fitted the wrong way round, so the circuit works before the gate drive is even powered.

The third case is a 24 V industrial input with a TVS clamp. The clamp is chosen at 33 to 36 V, which is above the 30 V rating of this part, so on a long inductive line the clamp voltage is not enough by itself and a 40 V part is the safer choice. That is the whole difference between the VBQA2311 and the VBQA2412 in the same body.

Gate drive and why 4.5 V matters

The threshold is minus 2.5 V, which means the part is only just conducting when the gate sits 2.5 V below the source and is fully enhanced somewhere near 8 to 10 V below it. On a 12 V rail with a 10 V gate drive, the gate is at 2 V when the part is on, and 8 milliohm is available. On a 5 V rail, or on a gate driven from a 3.3 V logic pin through a level shift, only 4.5 V is available and the resistance is 16 milliohm, double.

Doubling the resistance is not the only consequence. At the same current the loss doubles, and the temperature rise doubles with it, so a part that is comfortable at 10 A on a 10 V gate is marginal at 10 A on a 4.5 V gate. The table above gives the conduction figure at the 10 V gate because that is the number the part is sold on, and the working number for a 5 V system is the other one.

The gate to source limit is 20 V in both directions, and on a 24 V rail the gate sits at 24 V when the part is off. A zener across gate and source, or a resistor divider on the gate, keeps the difference inside the limit. A gate resistor in series with the pull down also slows the turn on, which is what limits the inrush into the load capacitance.

Losses and the pad

The die makes 0.8 W at 10 A, 3.2 W at 20 A and 9.8 W at 35 A from the 8 milliohm figure. Hot, the resistance rises by about 40 per cent from 25 C to 125 C, so a 20 A load is nearer 4.5 W than 3.2 W. A 5 by 6 pad soldered to four square centimetres of two ounce copper is about 25 to 30 K per watt in still air, so 4.5 W is a 110 to 135 K rise and the 9.8 W figure is not a continuous rating on a board.

The honest continuous current for this body on a normal board is 10 to 15 A, and 20 A only with a metal core or forced air. The 35 A on the data page is the bond wire and die limit at a 25 C case, which is a package capability rather than a board capability. Buyers who size from the headline number and then find the part at 140 C on the bench have usually made this mistake.

Where a board is being re-quoted against a second source, the pin to pin cross reference page covers which parameters have to match before a substitute is proposed, including the threshold and the gate charge that decide whether the existing drive still works.

Inrush is the number that is not on the page. A 12 V rail with 470 microfarad of input capacitance pulls several hundred amps for a few microseconds if the switch closes straight onto it, and the 35 A rating is not an inrush rating. The usual remedy is a resistor in the gate path so the part turns on over a millisecond, which spreads the charge into the capacitor across a region where the part is dissipating tens of watts for a very short time. Whether that survives is a safe operating area question, and the vendor page carries no such curve, so the full datasheet has to be requested before the part is released into a hot swap circuit.

The sourcing side of this part is covered on the power management cross reference. For a minus 30 V P channel used as a high side switch, that page covers how the adjacent voltage classes are compared before a substitute is proposed.

Questions we get on this code

Is it a drop in for a 30 V N channel plus charge pump? Electrically no. The gate is referenced to the source, the drive is inverted, and the body diode points the other way. The board has to be changed, not just the part.

Can the gate be driven from a 3.3 V pin? Only through a level shift or an open drain with a pull up to the rail. At 3.3 V below the source the part is barely on and the resistance is well above the 16 milliohm printed for 4.5 V.

What happens if the load is inductive? The body diode clamps the drain to the source plus a diode drop, which is the same as an N channel low side switch except the diode points the other way. A freewheel path across the load is still needed.

Are the 35 A and the 8 milliohm measured together? No. The current is the package limit and the resistance is at a stated gate voltage and a 25 C junction. Both derate, and they derate in opposite directions.