Contact Us

VBQA2202K

Brand: VBsemi
VBsemi VBQA2202K is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA2202K — Discrete & Power Semiconductors | Superb Automation

VBQA2202K

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA2202K from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA2202K: a 200 V P channel in a DFN 5 by 6

The VBQA2202K is a single P channel MOSFET in the DFN8 5 by 6 body, printed at minus 200 V drain to source, plus or minus 20 V on the gate, a minus 2 V threshold, minus 4 A of drain current, 2200 milliohm at a 4.5 V gate and 2000 milliohm at a 10 V gate. The structure is trench. It is the highest voltage P channel part in this band and the one that appears where a high side switch has to be driven without a floating supply.

A P channel at 200 V is expensive silicon because the hole mobility is a third of the electron mobility, so the die has to be three times the area of an N channel of the same resistance. That is why 2 ohm at 4 A is the state of the art at this voltage and why most 200 V high side switches are N channel parts with a charge pump instead.

The reason a P channel still gets chosen is simplicity. The gate is pulled below the source by a resistor and a small NPN, the part turns on with no bootstrap, no isolated supply and no refresh timing. On a circuit that switches once per second, such as a battery disconnect, an input reverse protection path or a load shed, that simplicity is worth the die cost.

Key data for the VBQA2202K

ConfigurationSingle P channel
PackageDFN8 5 by 6, exposed pad on the drain
VDSMinus 200 V
VGSPlus or minus 20 V
VthMinus 2 V typical
IDMinus 4 A at a 25 C case
RDS(on) at 4.5 V2200 milliohm
RDS(on) at 10 V2000 milliohm
StructureTrench
Conduction at 0.5 A0.5 W
Conduction at 1 A2 W
Conduction at 2 A8 W
Conduction at 3 A18 W

Where a 200 V P channel is used

A 110 to 150 V DC bus with an input disconnect is the first case. The switch sits in the positive line, the source is at the bus, and the gate is pulled to ground through a resistor to turn it on. When the bus is 150 V and the part is 200 V, the margin is 1.3, which is enough for a regulated rail and not enough for a line that can surge. Those circuits usually put a TVS across the input as well.

A minus 48 V telecom line is the second case. The rail is 48 V nominal and 60 V at float, and a 200 V part has a large margin, but the reason it is picked there is the polarity: on a minus 48 V system the return is positive, and a P channel in the return line is the simplest disconnect.

The third is a battery string on a 96 to 144 V pack, where the disconnect has to hold the full pack voltage and carry 1 to 3 A of standby load. At 2 ohm and 2 A the loss is 8 W, so those circuits use a bigger part or a relay and this part only for the pre charge path.

The gate drive of a P channel

The gate has to be taken 10 V below the source to reach 2 ohm, and the source sits at the bus. That means the gate driver is referenced to the bus, not to ground. A resistor from gate to source holds the part off, an NPN or a small N channel pulls the gate down to turn it on, and the gate to source voltage must never exceed 20 V in either direction.

On a 150 V bus the gate sits at 150 V when the part is off and at 140 V when it is on, so anything connected to the gate sees the full bus. A zener across gate and source clamps the difference, and a resistor in series with the gate limits the charge current into the gate capacitance. Without the zener, a spike on the bus couples through the gate to source capacitance and can take the part out.

Turn off is the slow direction. A P channel turns off when the gate is pulled up to the source, and the only current available is the gate to source resistor. At 2 ohm and a gate charge of 30 to 60 nC, a 10 k resistor gives a turn off in 30 to 60 microseconds. That is fine for a disconnect and far too slow for a switching converter.

Losses, and the pad as a heatsink

At 2 ohm the die makes 0.5 W at 0.5 A, 2 W at 1 A, 8 W at 2 A and 18 W at 3 A. Hot, the resistance roughly doubles, so 2 A becomes 16 W and 1 A 4 W. A 5 by 6 pad on four square centimetres of copper is 25 to 35 K per watt, which means 2 A gives a 200 to 280 K rise. The honest continuous current is 0.7 to 1 A on a board and 1.5 A only with a metal core or a fan.

The body diode in a P channel conducts from drain to source when the gate is off and the drain is above the source. In a battery disconnect the diode is what carries the load during the off state if the load has any path to ground, so the part has to be oriented so the diode blocks. Getting this backwards is the most common mistake with a P channel disconnect: the circuit works on the bench, and the battery drains through the diode in the field.

Inrush is the other number to check. A 150 V bus with 100 microfarad of input capacitance and no pre charge draws hundreds of amps for a few microseconds when the switch closes. The 4 A rating is not an inrush rating, so a pre charge resistor or a current limited path is needed, and this part should be the path that closes after the capacitors are charged.

Where a board is being re-quoted against a part that has gone short lead, the power management cross reference page covers how an adjacent voltage class is compared before a substitute is proposed, and the obsolete RF part replacement page covers the same discipline for a code that has stopped.

The sourcing side of this part is covered on the power management cross reference. For a 200 V P channel code, that page covers how an adjacent voltage class is compared.

Questions we get on this code

Can it switch at 100 kHz? No. The gate has to be pulled to the source to turn off, the pull up is a resistor, and the turn off is tens of microseconds. This is a disconnect part, not a converter switch.

What is the gate to source limit? Plus or minus 20 V. On a 150 V bus the gate sits at the bus, so the drive has to be referenced to the source and clamped with a zener.

Is the pad the drain or the source? The pad is the drain. On a high side P channel that is the load side, so the copper under the pad sits at the load voltage when the part is off.

Can two of them be paralleled for 4 A? Yes, with a separate gate resistor on each so the two share the current during the slow turn on. Two parts in parallel halve the loss and also halve the temperature rise, which matters here more than in a low voltage part.