VBK2298
Product Specifications
VBK2298
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBK2298 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBK2298: a single P channel in an SC70-3 for high side switching
The VBK2298 is a single P channel in a three lead SC70, the package that measures about 2 by 2 millimetres. It is rated at minus 20 V, carries minus 3.1 A, and prints 100 milliohm at a 2.5 V gate against 80 milliohm at 4.5 V. The threshold is minus 0.6 V and the gate window is plus or minus 12 V.
A P channel is the shortest path to a high side switch that needs no charge pump. The source sits on the rail, the drain feeds the load, and pulling the gate to ground turns the part on. On a 3.3 V or a 5 V rail that is often the whole circuit, which is why parts in this package still outnumber the more efficient alternatives in small products.
The trade is on resistance. At 80 milliohm a 1 A load drops 80 millivolt and burns 80 milliwatt. In an SC70 that is already most of the thermal budget in still air. Above about 1.5 A the package, not the silicon, is the limit.
Key data for the VBK2298
| Configuration | Single P channel |
| Package | SC70-3, three leads, surface mount |
| VDS | Minus 20 V |
| VGS | Plus or minus 12 V |
| Vth | Minus 0.6 V |
| ID | Minus 3.1 A |
| RDS(on) at 2.5 V | 100 milliohm |
| RDS(on) at 4.5 V | 80 milliohm |
| Technology | Trench |
| Gate drive | Pull to ground to conduct, pull to source to block |
| Body diode | Anode at the drain, so it conducts from load to rail |
| Thermal path | Three small leads, no exposed pad |
Threshold at minus 0.6 V and what it costs in leakage
A threshold of minus 0.6 V means the part is barely off when the gate sits at 0.4 V below the source. In a battery product that is a real leakage path: a weak pull up resistor and a warm board can lift the gate 0.3 V and the part starts to conduct. A pull up of 100 kilo ohm against a 0.6 V threshold is not a reliable off state. Use 10 kilo ohm or less, and measure the leakage at 85 C.
The low threshold is what makes the part work on a 2.5 V rail, which is the first column of the catalogue. At 2.5 V the on resistance is 100 milliohm, a quarter worse than at 4.5 V. For a 500 mA load that is 25 milliwatt instead of 20, which is a small price for not needing a driver.
The gate window of 12 V matters more here than on a 20 V part. On a 12 V rail the gate sees the full rail in the off state, which is exactly at the limit. Any ringing takes it over. On 12 V rails put a resistor in series with the gate or use a divider, and never connect the gate directly to a 12 V source through a switch.
Reverse polarity protection with a P channel
The common use for this package is a reverse polarity block at the input of a small product. The P channel is placed in the positive lead with its source toward the battery and its drain toward the load, gate pulled to ground through a resistor. Correct polarity turns the part on and the drop is the load current times 80 milliohm. Reversed polarity turns it off and the body diode blocks.
The catch is the gate clamp. With the battery reversed, the gate to source voltage is the battery voltage in the wrong direction, and a 12 V battery will exceed the 12 V gate limit through the pull down resistor. A zener between gate and source, or a series resistor that limits the gate current, is not optional on anything above 8 V.
The second catch is start up. The part is off until the gate is pulled down, and until then the load sees the body diode drop of about 0.8 V. For a product that has an inrush at power on, that means the first milliseconds are dissipated in the diode rather than in the channel.
Where a tiny P channel earns its place
Load switching on a sensor board, a battery disconnect in a handheld instrument, a backlight enable line, a USB port power switch on a low current port, and a reverse polarity block on a 5 V input are all inside the comfort zone. The common factor is a load below 1 A and a rail below 12 V.
When the same part is bought for a product that ships for a decade, the sourcing question comes up when the code goes short. The power management cross reference page covers which printed parameters have to match and which can move.
The sourcing side of this part is covered on the one stop BOM sourcing. For a product whose bill of material carries several tiny switches, that page covers how the small parts are grouped and consolidated.
Questions we get on this code
Can I drive the gate from a 3.3 V logic pin? Yes, with the pin pulling the gate low to turn the part on. When the pin is high at 3.3 V and the rail is 5 V, the gate is 1.7 V below the source, which is above the minus 0.6 V threshold, so the part stays off but only just. Check the leakage in that state.
What is the maximum continuous current? About 1 A in still air on a small pad, and 1.5 A with a larger drain pad. The minus 3.1 A headline is a pulsed figure at 25 C case.
Does the body diode conduct in normal operation? It does during start up and during any interval when the load is back fed. Its drop is about 0.8 V, so a 1 A back feed is 800 milliwatt, which the package will not hold.
Is an SC70-3 available on tape in the quantities a production line needs? Yes, the package is a standard 8 mm tape part. Ask for the reel size with the quote, since the small packages are often packed 3000 to a reel.