Contact Us

VBQA1603

Brand: VBsemi
VBsemi VBQA1603 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA1603 — Discrete & Power Semiconductors | Superb Automation

VBQA1603

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA1603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA1603: 60 V and 3 milliohm in DFN 5 by 6, with a hot resistance row that triples

The VBQA1603 is a 60 V N channel trench MOSFET in the DFN 5 by 6 body. The product summary gives 60 V, 3 milliohm at a 10 V gate and 5 milliohm at 4.5 V, with a 100 A continuous rating at a 25 C case and a 175 C junction limit, and the application list on the sheet is a single line that names nothing in particular, so the ratings have to carry the argument.

What makes this sheet different from the other 60 V parts in the same body is that it prints on resistance at three temperatures rather than one. Three milliohm at 25 C, 8 milliohm at 125 C and 10 milliohm at 175 C. That is the whole thermal argument in three numbers, because the loss at a given current more than triples across the operating range, and a calculation that uses the 25 C row will understate the dissipation by a factor of three.

The current table has two case rows and nothing at the board level for current, which is unusual and worth noting. A hundred amps with the case at 25 C, 85 A at 100 C, and a dissipation row that drops from 136 W to a board figure of 3 W in 25 C air. The part is clearly aimed at a copper plane, a heatsink or a forced air path rather than at a bare board.

The gate is symmetric at plus or minus 20 V with a 1 V to 3 V threshold and a 2 V typical, and the input capacitance of 2650 pF with a reverse transfer of 225 pF is a combination that switches fast at 10 A and needs a real driver at 50 A. Total gate charge is 47 nC typical and 70 nC maximum, a spread of 49 per cent.

The parameter table in full

Drain to source voltage60 V
Gate to source voltage, continuousplus or minus 20 V
Continuous drain current, case at 25 C100 A
Continuous drain current, case at 100 C85 A
Pulsed drain current100 A
Continuous source current, diode conduction80 A
Avalanche current70 A
Single avalanche energy at 0.1 mH and 1 per cent duty125 mJ
Maximum power dissipation, case at 25 C136 W
Maximum power dissipation, board at 25 C3 W for 10 s, 8.3 W
Junction to ambient, 10 s, typical and maximum15 and 18 C per watt
Junction to ambient, steady state, typical and maximum40 and 50 C per watt
Junction to case, typical and maximum0.85 and 1.1 C per watt
Breakdown voltage at 250 microamp60 V
Gate threshold at 250 microamp1 V minimum, 2 V typical, 3 V maximum
Gate body leakage at 20 V100 nA maximum
Drain leakage at 60 V, 25 C, 125 C and 175 C1, 50 and 250 microamp
On state drain current at 10 V gate60 A minimum
On resistance at 10 V gate and 20 A, 25 C0.003 ohm typical
On resistance at 10 V gate and 20 A, 125 C0.008 ohm typical
On resistance at 10 V gate and 20 A, 175 C0.010 ohm typical
On resistance at 4.5 V gate and 15 A0.005 ohm typical
Forward transconductance at 20 A60 S typical
Input, output and reverse transfer capacitance at 25 V2650, 470 and 225 pF
Total gate charge at 10 V, 30 V and 50 A47 nC typical, 70 nC maximum
Gate source and gate drain charge10 and 12 nC
Turn on delay and rise time at 50 A and 2.5 ohm10 and 15 ns typical
Turn off delay and fall time, same conditions35 and 20 ns typical
Pulsed diode forward current60 A
Body diode forward drop at 20 A1.0 V typical, 1.5 V maximum
Body diode recovery time45 ns typical, 100 maximum
Operating junction and storage rangeminus 55 to plus 175 C

Three on resistance rows and one thermal ceiling

At a 25 C case the 136 W row through 1.1 C per watt is 115.6 C of rise, which lands on a 140 C junction, so the row is consistent with the 175 C limit and holds a margin of 35 C for the resistance rise inside the die. A hundred amps at 3 milliohm is 30 W and the die is comfortable; at 175 C the same current through 10 milliohm is 100 W, which the 0.85 C per watt typical path turns into 85 C of rise and only works with the case held near 90 C.

On a board the picture changes completely. The steady state ambient row is 50 C per watt worst case, which allows 2.5 W for a 150 C junction in a 25 C room, and 2.5 W through 3 milliohm is 29 A. At the 175 C limit the allowance is 3 W and 17 A, so a fanless board carries a fifth of the headline current. The 8.3 W and 3 W dissipation rows in the table are the same arithmetic with two different pulse conditions, and neither of them describes a continuous load.

The board thermal figures are also where the 175 C junction earns its keep. A part rated to 175 C has 150 C of usable rise from a 25 C room rather than 125 C, which is a 20 per cent larger thermal budget, and that is worth having in a converter that runs hot but not in one that runs at 25 A continuous.

Where the rows in this sheet do not line up

The avalanche row is generous beyond what its test can store. Energy is 125 mJ against a 0.1 mH coil and a 70 A avalanche current, and half of 0.1 mH times 4900 is 245 mJ stored, so the part is credited with half of what the test delivers. That is the safe direction, and it means a 125 mJ clamp is genuinely inside the rating rather than at the edge of it.

The pulsed current row is a puzzle. 100 A pulsed with a 100 A continuous rating at a 25 C case means the pulsed row adds nothing, while the same family normally prints a pulse figure several times the continuous one. Either the continuous row is a package limited value and the pulse row was copied from it, or the pulsed row is wrong. Our reading is that both rows are package limited and the die can carry more, but a customer sizing a 100 microsecond pulse should not rely on this table for margin.

The dissipation rows across temperatures move in the wrong direction in the text dump. The 25 C case row is 136 W and the 70 C case row appears as 4.77 W in one place and 3 W in another, while a lower case temperature cannot dissipate more than a higher one at the same junction. The consistent pair is 136 W at 25 C with the 1.1 C per watt path, and the other figures look like they were copied from a smaller body in the same family.

Where a 60 V, 3 milliohm part earns its place

A 48 V to 12 V converter with a 60 V margin, a 24 V motor drive at 30 A, a battery disconnect on a 48 V pack and a synchronous rectifier in a 400 W adapter all sit inside the ratings with a plane under the pad. The 47 nC of gate charge allows 300 kHz switching from a 1 A driver, and the 20 ns fall time keeps the turn off loss under 2 W at 50 A.

It is the wrong part for a 60 V rail without a clamp, where the leakage spike eats the 15 V of headroom, and for a fanless board above 20 A. An 80 V part or a larger body is the answer in both cases, and the three temperature rows in this sheet are exactly what a customer needs to see before making that call.

Our power management cross reference work keeps the hot resistance rows at 125 C and 175 C per approved alternate rather than a single 25 C figure, because at 3 milliohm the difference between a part that triples and one that only doubles is 20 W at 100 A, and no summary page shows it.

Questions we answer before a reel is booked

First, the turn off edge. A 225 pF reverse transfer capacitance against 2650 pF of input capacitance gives a ratio of 0.085, which is a fast switch, and at 50 A into a 30 nH loop the drain will ring. The gate resistor and the snubber have to be chosen together, and the 35 ns turn off delay leaves little room for a slow driver.

Second, the diode. The reverse recovery time of 45 ns typical and 100 ns maximum belongs to a body diode that is not meant to conduct in steady state, so a synchronous rectifier needs a dead time short enough that the diode carries only the commutation interval, and the 1.5 V maximum forward drop is the number that sets the loss in that interval.

Third, the alternate. A 60 V part at 3 to 4 milliohm in a 5 by 6 body comes with hot resistance rows from 1.8 to 3.5 times the cold figure and avalanche ratings from 30 to 250 mJ. We hold both rows per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the 5 by 6 land pattern and the exposed pad dimension, since the pad is what carries the heat in this body.