VBQA1401
Product Specifications
VBQA1401
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQA1401 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQA1401: 40 V, 0.86 milliohm and a 180 A rating that the package, not the die, sets
The VBQA1401 is a 40 V N channel trench MOSFET in the DFN 5 by 6 body, and its product summary is unusually dense: 40 V, 0.86 milliohm at a 10 V gate, 1.16 milliohm at 4.5 V, 59.2 nC of gate charge at 4.5 V and a 180 A continuous rating that the sheet itself marks as package limited.
That package note is the whole story of the part. The die can carry more than the eight lead frame allows, so the 180 A row applies only with the case held at 25 C and the drain pad soldered to a plane that spreads the heat. At a 70 C case the row is 144 A, on a one inch board in 25 C air it is 72 A, and in 70 C air it is 36 A. The four rows are one part seen through four thermal paths.
Applications listed are synchronous rectification, OR-ing, high power density DC to DC, voltage regulator modules, DC to AC inverters and load switches. Every one of them is a low voltage, high current path where conduction loss dominates and the switching loss is a smaller share, which is why the part spends its silicon on resistance rather than on gate charge.
The gate is asymmetric and the sheet says so: plus 20 V and minus 16 V, with a 1.0 V to 2.2 V threshold. A trench part with a 1 V floor turns on hard with any gate signal above 3 V, and the negative 16 V limit is generous enough for a driver that swings below ground on turn off. The 5.6 mV per C threshold coefficient means the threshold falls as the die heats, so a hot part is easier to turn on and harder to keep off.
The parameter table in full
| Drain to source voltage | 40 V |
| Gate to source voltage | plus 20 V, minus 16 V |
| Continuous drain current, case at 25 C and 70 C | 180 A and 144 A |
| Continuous drain current, board at 25 C and 70 C | 72 A and 36 A |
| Pulsed drain current at 100 microsecond | 720 A |
| Continuous diode current, case at 25 C | 90 A in the ratings table, 180 A in the diode table |
| Single pulse avalanche current, 0.1 mH | 45 A |
| Single pulse avalanche energy | 101 mJ |
| Maximum power dissipation, case at 25 and 70 C | 100 and 64 W |
| Maximum power dissipation, board at 25 and 70 C | 6.25 and 4 W |
| Junction to ambient, 10 s, typical and maximum | 15 and 20 C per watt |
| Junction to ambient, steady state maximum | 54 C per watt |
| Junction to case, typical and maximum | 0.95 and 1.25 C per watt |
| Breakdown voltage temperature coefficient | 25 mV per C |
| Gate threshold at 250 microamp | 1.0 V minimum, 2.2 V maximum |
| Gate leakage at plus 20 and minus 16 V | 100 nA maximum |
| Drain leakage at 40 V, 25 C and 55 C | 1 and 10 microamp |
| On state drain current at 10 V gate | 50 A minimum |
| On resistance at 10 V gate and 20 A | 0.00086 ohm typical |
| On resistance at 4.5 V gate and 15 A | 0.00116 ohm typical |
| Forward transconductance at 20 A | 106 S typical |
| Input, output and reverse transfer capacitance at 20 V | 8445, 1310 and 110 pF |
| Reverse transfer to input capacitance ratio | 0.013 typical, 0.026 maximum |
| Total gate charge at 10 V and at 4.5 V | 129 and 59.2 nC typical |
| Gate source, gate drain and output charge | 25, 13 and 61 nC |
| Gate resistance at 1 MHz | 0.2, 0.7 and 1.2 ohm |
| Turn on delay and rise time at 10 V drive | 19 and 10 ns typical |
| Turn off delay and fall time at 10 V drive | 53 and 10 ns typical |
| Turn on delay and rise time at 4.5 V drive | 56 and 159 ns typical |
| Turn off delay and fall time at 4.5 V drive | 54 and 36 ns typical |
| Body diode forward drop at 30 A | 0.71 V typical, 1.1 V maximum |
| Body diode recovery time | 64 ns typical, 128 maximum |
| Operating junction and storage range | minus 55 to plus 150 C |
The two thermal paths, and why 180 A is a case temperature figure
At a 25 C case the junction to case path of 1.25 C per watt allows 100 W, which is the dissipation row, and 100 W through 0.86 milliohm is 341 A of conduction current. The package limits the current before the die does, which is what the 180 A row and its footnote say, and the 720 A pulse row is the die speaking rather than the lead frame.
On a board the number falls by an order of magnitude. 20 C per watt for 10 s allows 6.25 W, which through 0.86 milliohm is 85 A, and the steady state row of 54 C per watt allows 2.3 W and 52 A. The printed 72 A board row assumes the 10 s path with a hot resistance rather than the cold one, and a continuous 72 A on a bare board is not inside the steady state row at all.
The parallel case is where this part becomes interesting. Two of them at 0.86 milliohm give 0.43 milliohm before the resistance rise, and sharing depends on the threshold match and the gate resistance spread rather than on the resistance itself. The 0.2 to 1.2 ohm gate resistance window is a wide one, and two parts at opposite ends of it will not switch at the same instant.
What the 4.5 V rows cost, and where the diode rows disagree
The 4.5 V drive rows are not a small step down from 10 V, they are a different operating point. On resistance rises from 0.86 to 1.16 milliohm, 35 per cent, gate charge falls from 129 to 59.2 nC, and the rise time goes from 10 ns to 159 ns, a factor of nearly sixteen. A load switch driven from a 5 V rail therefore switches slowly and cleanly, while a synchronous rectifier driven from the same rail would dissipate far more in the transition than it saves in gate drive.
The diode current rows contradict each other. The ratings table prints 90 A continuous source drain diode current at a 25 C case and the diode table prints 180 A for the same condition. Both cannot be right for a lead frame that limits the channel to 180 A, and our reading is that the diode table row was copied from the channel rating. The ratings table figure is the one to use when a synchronous rectifier has to survive a dead time.
The avalanche rows are consistent. 101 mJ is printed against a 0.1 mH coil and a 45 A start, and half of 0.1 mH times 2025 is 101.25 mJ. The row and its test agree to within a rounding step, which makes the avalanche figure usable for a motor or a relay load without asking for a separate report.
Where a 40 V sub milliohm part earns its place
A 40 V to 12 V synchronous buck at 60 A, an OR-ing switch on a battery bus, a load switch on a 20 A rail and a motor drive with a 24 V bus all sit inside the ratings. The 61 nC of output charge and the 1310 pF of output capacitance set the switching loss at high frequency, and above 300 kHz the part stops being the cheapest option per watt.
It is the wrong part for a 48 V rail, where 40 V leaves almost nothing after the leakage spike, and for a hot ambient without a plane, where the steady state board row caps the current near 50 A. A pair in parallel or a larger body is the answer in both cases.
Our power management cross reference work keeps the threshold window, the gate resistance spread and the diode current row per approved alternate, because in a parallel arrangement those three decide whether the parts share current at all, and none of them appears in a comparison that stops at voltage and resistance.
Questions we answer before a reel is booked
First, the drive. With a 1.0 V floor and a 2.2 V ceiling, the part turns on from almost any logic level, which is convenient and also means a floating gate will turn it on. The gate resistor and the pull down have to be chosen for the off state, and the minus 16 V limit allows a negative off bias if the board has ringing.
Second, the sharing. In a two device parallel stage the 0.2 to 1.2 ohm gate resistance and the 1.0 to 2.2 V threshold window combine into a turn on time spread that can put most of the switching loss in one device. We ask for the gate resistance bin and the threshold bin before approving a parallel pair.
Third, the alternate. A 40 V part at 0.8 to 1.2 milliohm in the same body comes from several suppliers with output capacitance between 4000 and 12000 pF and avalanche ratings from 20 to 150 mJ. We hold those rows per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the 5 by 6 pad, the pin 1 marker and the exposed pad area, since a body with a smaller pad will not reach the same board thermal row.