Contact Us

VBL19R20S

Brand: VBsemi
VBsemi VBL19R20S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL19R20S — Discrete & Power Semiconductors | Superb Automation

VBL19R20S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL19R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL19R20S: 900 V and 20 A in a TO263

The VBL19R20S is a single N channel MOSFET rated at 900 V drain to source with a plus or minus 30 V gate window and a threshold of 3.5 V. It carries 20 A and its on resistance is 270 milliohm at a 10 V gate. The silicon is a multi epitaxial super junction structure and the body is TO263, the surface mount package with a tab that the industry also calls D2PAK.

Nine hundred volts and 270 milliohm in a surface mount body is a converter part. At 5 A it drops 1.35 V and dissipates 6.75 watt, which the tab handles on a copper area with a thermal plane. At 10 A it is 27 watt and the part needs a real heatsink. The 20 A rating is a die limit and a pulse number.

The voltage class is what makes this part interesting. A 900 V rating covers a 400 V rectified three phase mains with margin, a 480 V industrial rail, and the flyback or forward topology that runs from them. A 650 V part would be marginal on a 400 V bus with a surge, and a 1200 V part would have three times the resistance at the same die area.

Key data for the VBL19R20S

ConfigurationSingle N channel
PackageTO263, surface mount with tab
VDS900 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID20 A
RDS(on) at 10 V270 milliohm
TechnologyMulti epitaxial super junction
Gate chargeNot published on the catalogue page, and on a super junction part it drives the switching loss
Body diodeIntrinsic, with a sharp recovery that matters in a bridge
Thermal pathTab soldered to a copper island with a thermal plane below
CreepageThe tab is at the drain, so the high voltage node is a large copper area

Super junction at 900 V and the recovery it brings

A multi epitaxial super junction structure reaches 270 milliohm at 900 V by replacing part of the drift region with alternating p and n columns. That is what allows a surface mount body to hold a part that would have needed a TO247 a generation ago.

The cost is the body diode. A super junction device has a diode with a very fast but very abrupt recovery, and in a bridge or a synchronous topology that recovery produces a current spike and a ringing that a planar part of the same voltage would not. Snubbers, a soft recovery parallel diode, or a topology that never forces the body diode into conduction are the usual answers.

The gate charge is also higher than the resistance alone would suggest, because the columns add capacitance. Driving a 270 milliohm, 900 V die from a weak pin produces a slow edge and a long switching interval, and at 900 V the switching loss per transition is large. A driver with a defined peak current and a gate resistor chosen from the charge, not from habit, is the minimum.

Twenty amps and the surface mount tab

The TO263 tab is large and it is the only thermal path, so the copper island under it is the rating. At 5 A and 6.75 watt a four square centimetre island on two layers with a via array gets the junction around 70 degrees above ambient, which is workable. At 10 A the loss doubles and the junction climbs past 140 degrees, which is not.

The high voltage node sits on the tab and on the copper island, and at 900 V that island is a large area at a dangerous potential. Spacing to the rest of the circuit, the slot in the board if there is one, and the conformal coating are all part of the assembly's voltage rating, not just of the package.

Reflow is the only mounting method. A tab of this size does not hand solder reliably, and a void under the tab becomes a hot spot at 6 watt. First article X-ray is the standard check for a board that carries this body.

Consolidating high voltage parts across a product line

Converters in the 800 to 900 V class tend to use two or three part numbers across a family of products, and consolidating them is worth more than shaving a few milliohm. Our vendor consolidation page covers how a programme reduces the number of sources without losing the ability to cover a shortage on any single part.

The comparison points for a substitute at this voltage are the body diode recovery, the gate charge and the creepage, in that order. A candidate with the same resistance and a softer diode may be the better part even if it is 20 milliohm worse, because the recovery loss in a bridge can exceed the conduction difference.

The sourcing side of this part is covered on the component obsolescence management. For a 900 V part with a thin second source, that page covers how end of life is tracked before it becomes an emergency.

Questions we get on this code

Is 20 A continuous? No. At 270 milliohm the continuous current on a surface mount tab is nearer 5 A without a heatsink and 10 A with one.

Can it run from a 400 V bus? Yes, with margin for a surge. A 650 V part on the same bus would be marginal, which is the reason to choose this class.

Does the body diode need a snubber? In a bridge or a synchronous topology, yes. The recovery is abrupt and it will ring without one.

What is the packing? TO263 normally ships on a 500 or 800 piece reel. We confirm the reel size and the orientation on the quotation.