VBPB1204N
Product Specifications
VBPB1204N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBPB1204N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBPB1204N: 200 V, 0.048 ohm and 60 A in TO-3P, with a 20 mJ avalanche ceiling
The VBPB1204N is a 200 V N channel trench MOSFET in the TO-3P body, rated 60 A at a 25 C case and 40 A at 100 C, with 0.048 ohm at a 10 V gate and 20 A of test current. The product summary prints two on resistance values, 0.048 ohm at 15 V and 0.046 ohm at 10 V, which is unusual because the lower gate voltage shows the lower resistance and either the rows or the test currents have been transposed.
At 200 V the part sits between the 100 V battery class and the 400 V off line class. It covers a 110 V mains rectified rail at 155 V, a 96 V to 120 V battery string, a 150 V DC bus in a telecom rectifier, an LED driver on a 150 V rail, and a class D audio stage. At 0.048 ohm, 20 A sheds 19.2 W and 30 A sheds 43.2 W, so the practical continuous current with a heatsink is 20 A to 25 A.
Two rows set this part apart from the rest of the shipment. The avalanche energy is 20 mJ, the smallest here by a factor of thirty, and the rise time is 170 ns typical against a 9 ns fall, which is a factor of nineteen and the largest asymmetry in the batch. Both are consequences of a large die with a high input capacitance and a thin drift region.
The parameter table in full
| Drain source voltage | 200 V |
| Gate source voltage | plus or minus 25 V |
| On resistance at 10 V gate and 20 A, 25 C | 0.048 ohm typical |
| On resistance at 15 V gate and 20 A | 0.046 ohm typical |
| On resistance at 100 C and at 150 C | 0.088 and 0.120 ohm |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Gate body leakage at 20 V and at 25 V | plus or minus 100 nA and plus or minus 300 nA |
| Drain leakage at 200 V, 25 C, 100 C and 150 C | 1, 25 and 250 microamp |
| On state drain current at 10 V gate | 40 A minimum |
| Forward transconductance at 20 A | 25 S minimum |
| Input, output and reverse transfer capacitance | 3100, 300 and 135 pF |
| Total gate charge at 15 V, 100 V and 50 A | 85 nC typical, 127 maximum |
| Total gate charge at 10 V, same conditions | 57 nC typical, 85 maximum |
| Gate source and gate drain charge | 14 and 20 nC |
| Gate resistance at 1 MHz | 1.2 ohm typical, 1.8 maximum |
| Turn on delay and rise time at 100 V and 50 A | 16 and 170 ns typical |
| Turn off delay and fall time, same conditions | 27 and 9 ns typical |
| Continuous source drain diode current | 36 A |
| Pulsed diode forward current | 80 A |
| Body diode forward drop at 20 A | 0.86 V typical, 1.5 maximum |
| Reverse recovery time at 40 A | 116 ns typical, 175 maximum |
| Peak reverse recovery current and charge | 9 A and 0.53 microcoulomb |
| Single pulse avalanche current and energy at 0.1 mH | 20 A and 20 mJ |
| Maximum power dissipation, case at 25 C and ambient at 25 C | 166 W and 3.12 W |
| Junction to case and junction to ambient on board | 0.75 and 40 C per watt |
| Continuous drain current at 25 C and 100 C case | 60 A and 40 A |
| Pulsed drain current | 180 A |
A thermal pair that closes, and a 60 A row that sits on the ceiling
166 W through 0.75 C per watt is 124.5 C, which is the 150 C rise from a 25 C case to a 175 C junction, and 3.12 W through 40 C per watt is 124.8 C for the same rise. Both rows reconcile with the thermal table, so this sheet is internally consistent and the two dissipation figures can be used as printed.
The 60 A continuous row is a different matter. 60 A through 0.048 ohm is 172.8 W, which is 6.8 W above the 166 W dissipation row, and it needs a case at 45 C to hold the junction at 175 C. So the current row is dissipation limited and not silicon limited, and the 40 A row at a 100 C case, which sheds 76.8 W and takes 57.6 C of rise, is the figure that belongs in a circuit with an ordinary heatsink.
In still air 3.12 W is 8.06 A through the 25 C resistance and 5.1 A through the 150 C figure of 0.12 ohm. That is the honest continuous current on a board with no heatsink, and it is seven times below the headline. The printed hot rows make that calculation possible, which is why this sheet is easier to quote than the ones that print only a 25 C figure.
Avalanche at 20 mJ and a rise time of 170 ns
The avalanche row prints 20 mJ with a 20 A single pulse current into 0.1 mH, and one half of 0.1 mH times 400 is exactly 20 mJ, so the row closes against its own test. But 20 mJ is a small number for a 60 A device and it means this part is not an avalanche rated switch in the sense the 600 V family is. Any unclamped inductive load, any relay coil and any motor with a long cable will exceed it, so a clamp is required.
The rise time of 170 ns typical and 260 ns maximum against a 9 ns fall is not a measurement error. It comes from the 3100 pF of input capacitance and the 1.2 ohm internal gate resistance being driven through a 1 ohm external resistor at 50 A, and from the transfer characteristic of a large die. In a hard switched stage the turn on loss is dominated by this, and at 100 kHz it can exceed the conduction loss at 20 A.
The diode is moderately fast: 116 ns of recovery with 0.53 microcoulomb and 9 A of peak reverse current at 40 A, which is better than the 600 V family's slow members and worse than its fast ones. The 0.86 V forward drop at 20 A is low, so in a bridge the diode conduction is cheap and the recovery is the cost.
Where 200 V and 0.048 ohm is the right choice
A 110 V mains rectified rail at 155 V in a 300 W adapter, a 96 V battery string disconnect, a 150 V LED driver at 1 A, and a class D audio stage at 200 W all use the part well, provided the heatsink carries 20 W to 40 W of channel loss. In the LED driver the low 0.86 V diode drop matters, because the diode conducts during the off time of a boost stage.
Where it does not fit is a 400 V bus, because 200 V has no margin over 390 V, and any application with an unclamped inductive load, because 20 mJ will be exceeded by a relay coil of 10 mH at 2 A. A customer who wants a 150 V rail with a motor load should be offered a 250 V or 300 V part with an avalanche rating above 100 mJ.
Our power management cross reference work keeps the avalanche energy, the rise time and the hot on resistance per approved alternate, because on a 200 V part the three together decide whether a circuit works, and none of them appears on a distributor page.
Questions we answer before a reel is booked
First, the two on resistance rows. 0.048 ohm at 15 V and 0.046 ohm at 10 V cannot both be right for a trench die, where the higher gate voltage always gives the lower resistance. Our reading is that the two values belong the other way round, and we quote the 10 V figure as 0.048 ohm and ask the vendor to confirm in writing before a build is released.
Second, the gate drive. The gate limit is plus or minus 25 V, which is higher than the 100 V part in this shipment and gives room for a 15 V drive, and the threshold window of 2.5 V to 4.5 V means a 10 V drive is the practical choice. The 20 nC of gate drain charge against 14 nC of gate source charge is a long plateau, so a 0.3 A driver is the minimum for a 100 kHz stage.
Third, the alternate. A 200 V part at 0.048 ohm is available with avalanche ratings from 20 mJ to over 200 mJ, and the difference decides whether a motor or a relay can be driven without a clamp. We hold that row per approved alternate, the incoming inspection plan checks the lot against it, and the pin to pin comparison starts from the TO-3P footprint and the tab rather than from the current rating.