Contact Us

VBPB1106

Brand: VBsemi
VBsemi VBPB1106 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBPB1106 — Discrete & Power Semiconductors | Superb Automation

VBPB1106

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBPB1106 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBPB1106: 100 V, 5.4 milliohm and 150 A in the TO-3P body

The VBPB1106 is a 100 V N channel trench MOSFET in the TO-3P body, rated 150 A at a 25 C case with 5.4 milliohm at a 10 V gate and 30 A of test current. The same sheet prints the hot rows that most of this shipment omits: 8 milliohm at 125 C and 12 milliohm at 175 C, which is a factor of 2.2 across the temperature range and the single most useful number on the page.

At 100 V the part covers the 48 V to 80 V rail: a battery disconnect in an e bike or a power tool pack, an OR-ing switch in a redundant 48 V supply, a hot swap stage, a motor drive in a cordless tool, and a synchronous rectifier in a 48 V output. At 5.4 milliohm, 30 A sheds 4.9 W and 60 A sheds 19.4 W, so the part is usually run at 20 A to 40 A rather than at the 150 A headline.

The package is TO-3P, which is the three lead plastic body with a metal tab and a larger footprint than TO-247. The thermal resistance is 0.5 C per watt junction to case and 40 C per watt junction to ambient, and the sheet prints a maximum power dissipation of 375 W at a 25 C case against 3.75 W at a 25 C ambient, which is a rare and welcome piece of honesty because the ambient row is the one that decides a board.

The parameter table in full

Drain source voltage100 V
Gate source voltageplus or minus 20 V
On resistance at 10 V gate and 30 A, 25 C5.4 milliohm typical
On resistance at 125 C and at 175 C8 and 12 milliohm typical
Gate threshold at 250 microamp2.0 V minimum, 4.0 V maximum
Gate body leakage at 20 Vplus or minus 100 nA
Drain leakage at 100 V, 25 C, 125 C and 175 C1 microamp, 50 microamp and 250 microamp
On state drain current at 10 V gate120 A minimum
Forward transconductance at 30 A25 S minimum
Input, output and reverse transfer capacitance9200, 750 and 280 pF
Total gate charge at 10 V, 50 V and 85 A110 nC typical, 160 maximum
Gate source and gate drain charge25 and 20 nC
Gate resistance at 1 MHz1.0 ohm typical, 6.2 maximum
Turn on delay and rise time at 50 V and 85 A20 and 30 ns typical
Turn off delay and fall time, same conditions55 and 130 ns typical
Continuous source drain diode current150 A
Pulsed diode forward current450 A
Body diode forward drop at 85 A1.0 V typical, 1.5 maximum
Reverse recovery time at 50 A30 ns typical, 45 maximum
Peak reverse recovery current and charge5.5 A and 0.19 microcoulomb
Avalanche current and repetitive energy at 0.1 mH75 A and 280 mJ
Maximum power dissipation, case at 25 C and ambient at 25 C375 W and 3.75 W
Junction to case and junction to ambient0.5 and 40 C per watt
Continuous drain current at 25 C and 125 C case150 A and 120 A, both package limited
Pulsed drain current450 A
Operating junction and storage rangeminus 55 to plus 175 C

375 W on the page, 300 W through the thermal pair, 3.75 W in air

0.5 C per watt with a 150 C rise from a 25 C case allows 300 W, so the 375 W dissipation row is 75 W above what the same sheet says the path can carry. It would need a junction to case figure of 0.4 C per watt. The ambient row of 3.75 W is the one that reconciles: 40 C per watt with a 150 C rise is 3.75 W exactly, which suggests the ambient row was calculated and the case row was rounded up.

3.75 W in air is 26 A through the 25 C on resistance and 22 A through the 125 C figure, so a 30 A load has to be bolted to something. At 150 A the channel sheds 121.5 W at 25 C and 180 W at 125 C, both above the 300 W ceiling only in the sense that the package and the bond wires are the limit, which the sheet says in two separate footnotes.

The hot rows make this part easier to quote than most of the shipment. A customer who runs 40 A continuously at a 100 C case has 12.8 W of channel loss, and the junction sits 6.4 C above the case at 0.5 C per watt. That arithmetic can be done from the printed rows without assuming a temperature coefficient, and it is why we ask for this sheet rather than a summary when a 48 V application is quoted.

The diode, the gate resistance spread and the slow fall

Recovery is 30 ns with 0.19 microcoulomb and 5.5 A of peak reverse current at 50 A forward, which is fast for a 100 V trench device and good enough for a synchronous rectifier at 200 kHz. The forward drop of 1.0 V at 85 A is high for a body diode, so in a stage where the diode conducts during dead time the loss is larger than the channel loss at low duty, and the dead time has to be short.

Gate resistance is printed as 1.0 ohm typical and 6.2 ohm maximum, a spread of six times. On a single device that only changes the edge shape, but on two devices in parallel it decides which one turns on first, and at 150 A the parts are always in parallel. The gate charge of 110 nC typical against 160 nC maximum has the same effect, and a pair selected from opposite ends of the spread will share current badly unless each has its own gate resistor.

The fall time of 130 ns typical and 160 ns maximum at 85 A is slow for a trench die and it is the number that limits the switching frequency in a hard switched stage. The rise time is 30 ns and the fall is 130 ns, which is a factor of four, and the difference comes from the 20 nC of gate drain charge and the large output capacitance of a 9200 pF input device.

Where a 100 V 5.4 milliohm part fits

A 48 V battery disconnect at 60 A, an OR-ing pair in a 1 kW redundant supply, a 36 V power tool drive, and a 48 V synchronous rectifier all use the low on resistance and the printed hot rows well. In the battery disconnect the 250 microamp of drain leakage at 175 C is the figure that decides whether a pack can sit for a month without a maintenance charge.

Where it does not fit is a 12 V rail, where a 60 V part at 1.45 milliohm in the same shipment halves the conduction loss, and any stage above 200 kHz, where the 130 ns fall time becomes the dominant loss. A customer who needs 200 kHz should be offered a part with a lower output capacitance, not a larger heatsink.

Our power management cross reference work keeps the hot on resistance rows and the gate resistance spread per approved alternate, because on a 100 V part in parallel the spread is what fails in the field and it is not visible on a summary page.

Questions we answer before a reel is booked

First, the current rows. Both the 150 A and the 120 A rows carry the package limited note, which means the silicon could pass more and the leads cannot. For a continuous 60 A load the package is not the limit and the thermal path is, so the question to ask is the case temperature the customer can hold rather than the current rating.

Second, the gate. A threshold window of 2.0 V to 4.0 V and a 20 V gate limit mean a 10 V drive is correct and a 15 V drive is outside the recommended range with no margin for ringing. The 25 nC of gate source charge against 20 nC of gate drain charge is a normal split for a trench die and the 30 ns rise time is set by the external resistor rather than by the driver.

Third, the alternate. A 100 V part at 5.4 milliohm is available from several suppliers with input capacitance from 6000 pF to 12000 pF, and that range changes the switching loss by a factor of two at 100 kHz. We hold the capacitance and the gate resistance per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the TO-3P footprint and the tab, since a TO-247 will not sit in the same hole pattern.