Contact Us

HXC50184

Brand: Hisiwell
Hisiwell HXC50184 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50184 — Discrete & Power Semiconductors | Superb Automation

HXC50184

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50184 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50184: 40 W across a full octave from 1.0 to 2.0 GHz, the row for GPS and Beidou

The HXC50184 is a 40 W single ended LDMOS transistor on 28 V, internally matched, with 12 dB of gain and 50 per cent drain efficiency, marked CW on the index row. The vendor page says the part covers the full 1.0 to 2.0 GHz band, works in Class AB, Class B and Class C, and handles CW and pulsed signals, linear or saturated. The application list is the most specific on this shelf: L band amplifier, ISM, and GPS or Beidou power amplifier.

An octave of bandwidth from one internally matched device is the point of the row. Most parts on this shelf are matched into a few hundred megahertz, which means a separate part per band. This one covers the navigation signals at 1227, 1561 and 1575 MHz, the 1.4 GHz and 1.8 GHz telemetry and trunking bands and the 2.4 GHz ISM band, all with the same device and the same board, which is what a multi band terminal or a test instrument needs.

The trade for that coverage is output and gain: 40 W and 12 dB, against 90 W and 14 dB on the row below it in frequency. A wider match means a lower impedance transformation ratio and more loss in the matching, and the index row shows the result honestly.

The HXC50184 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, single ended
Output, index row40 W
Output in dBm, calculated46.02 dBm
Voltage at 50 ohm, calculated44.7 V rms, 63.2 V peak
Peak against the 28 V rail, calculated2.26 times
Frequency range, index row1.0 to 2.0 GHz
Frequency range, vendor pageFull band 1.0 to 2.0 GHz
Drain rail, index row28 V
Gain, index row12 dB
Drive required, calculated2.5 W, or 34.02 dBm
Drain efficiency, index row50 per cent
DC input at that efficiency, calculated80 W, 2.86 A at 28 V
Heat to remove, calculated40 W
Mode, index rowCW
Modes on the vendor pageCW and pulsed, linear or saturated, Class AB, B and C
Application list, vendor pageL band amplifier, ISM, GPS and Beidou power amplifier
Output at 1 dB compressionNot published
Gain flatness across the octaveNot published
Thermal resistance, junction to caseNot published in text
Drain to source breakdownNot published in text
Input, output and feedback capacitanceNot published in text
Load mismatch toleranceNot published
Junction temperature maximumNot published in text
Package outlineNot published in text
Data sheet link on the vendor pagePoints at the site root, serves nothing
Parameters block on the vendor pagePublished as a picture, not as text
Orderable addendumNone published
Packing quantity and moisture levelNot published

Why a navigation transmitter wants this band

GPS L1 sits at 1575.42 MHz and L2 at 1227.6 MHz, Beidou B1 at 1561.098 MHz and B2 at 1207.14 MHz, and Galileo E1 shares 1575.42 MHz. Those four frequencies span 1207 to 1576 MHz, which is inside the octave, and a single 40 W device that covers the octave can serve a multi constellation transmitter without a band specific part per channel.

Navigation transmitters are usually not run at the full 40 W. A ground based augmentation station may transmit a few watts, and a simulator or a repeater may need more. The point of a 40 W device in those sockets is headroom: running at 10 W from a 40 W part gives eight decibels of backoff, which flattens the gain and the group delay across the band and keeps the modulation clean. That is the opposite of the pulse rows on this shelf, where the part is run at its limit and duty cycle is the only relief.

The index marks the row CW and the page says CW and pulsed, linear or saturated. For a navigation signal, which is a spread spectrum code on a carrier, the honest reading is Class A or AB at backoff rather than Class C at saturation, because a saturated amplifier destroys the code. That choice belongs to the amplifier builder, but it affects the bias and the heat, and it should be made before the heat sink is ordered.

Twelve decibels of gain across an octave

Twelve decibels is the lowest gain on this shelf apart from the 1000 W row, and on a 40 W part it means 2.5 W of drive. That is manageable, but the gain will not be flat across the octave. An internally matched device with 50 per cent bandwidth typically loses a decibel or two at the top of the band relative to the bottom, and no flatness figure is published here.

A system that needs flat output across 1.0 to 2.0 GHz should plan for a gain equaliser or a driver with a compensating slope, and should sweep the part at 1000, 1400, 1800 and 2000 MHz before freezing the driver specification. On a 2.5 W drive level the sweep is easy, because a signal generator and a power meter are enough.

The input match is internal, so the drive sees a reasonable return loss at the band centre, but the return loss at 2 GHz is not published. A pad on the driver output of one or two decibels costs little at this power and protects the driver from a mismatch that is worst at the band edge.

Forty watts of heat and a 28 V rail

At 50 per cent efficiency the part draws 80 W, which is 2.86 A at 28 V, and the heat is 40 W. That is the lightest thermal load on the shelf apart from the 45 W row. With a 0.5 degrees per watt flange the rise is 20 degrees and the junction sits near 105 degrees at an 85 degree flange, which leaves a wide margin. Even a 1 degree per watt flange is inside the limit.

The rail is 28 V, which is the standard for land mobile and for many battery backed systems. The current of 2.86 A is inside what a 5 A converter delivers, and at 40 W the transmitter can run from a 28 V bus without a boost stage. That combination is what makes the row attractive for a portable navigation or telemetry unit.

The voltage at the connector is 63 V peak, and at a 3 to 1 load it is 190 V. Standard 200 V parts cover the mismatch case, so the output network is inexpensive. The whole amplifier, driver included, can be built with parts that are in stock at any distributor, which for a 40 W product is often the deciding factor.

Where the HXC50184 sits on the shelf

The 1.0 to 2.0 GHz region of this shelf is thin: this 40 W row at 1.0 to 2.0 GHz, a 45 W row at 700 to 1700 MHz and a 180 W row at 700 to 1700 MHz, both of which are covered on their own pages. The higher power rows at 1.8 to 2.7 GHz sit above this band.

Read as a choice, this row is for a 28 V product that needs 40 W or 10 W with headroom, across any part of a full octave, on a board with a small heat sink. A buyer who needs more output in the same band steps to the 180 W row at 700 to 1700 MHz, which needs 1.8 W of drive at 20 dB and a much larger thermal path.

Before the purchase order goes out

Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route for a part whose only band evidence is a page sentence is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 40 W 1 to 2 GHz part should work from the RF power transistor cross reference, which lines the two up on band, gain and package rather than on the headline wattage. A bill of materials that carries the driver, the gain equaliser and the output passives can be placed through the one stop RF supply route.