Contact Us

VBP16R47S

Brand: VBsemi
VBsemi VBP16R47S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP16R47S — Discrete & Power Semiconductors | Superb Automation

VBP16R47S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP16R47S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP16R47S: 0.07 ohm at 46 A with a 600 V summary and a 650 V specification table

The VBP16R47S is a 600 V N channel super junction MOSFET in the TO-247AC body, and the first thing a buyer has to settle is which voltage the part actually is. Page one prints 600 V in the product summary, the absolute maximum table prints 600 V, and the electrical specification table prints 650 V for the same breakdown row. The family it belongs to is the 600 V one, and the 650 V row looks like a template left over from the fast diode sheets.

Setting the voltage question aside, the part is 0.07 ohm at a 10 V gate with 24 A of test current, 46 A at a 25 C case and 29 A at 100 C, in the same TO-247AC body as the 60 V part in this shipment. Its gate charge is high, 263 nC maximum, and its body diode is slow, 753 ns typical, which places it firmly in the hard switched, diode-free application set: a continuous conduction power factor stage, a two switch forward, an induction heater, a welding supply.

This is also the only sheet in the shipment whose dissipation row closes exactly against its thermal pair. 417 W through 0.3 C per watt is 125.1 C, which is the 150 C junction from a 25 C case, so the headline is the thermal path written out and there is no contradiction to report.

The parameter table in full

Drain source voltage, product summary and absolute maximum600 V
Drain source breakdown in the specification table650 V
Gate source voltageplus or minus 30 V
On resistance at 10 V gate and 24 A0.07 ohm typical
Gate threshold at 250 microamp2 V minimum, 4 V maximum
Gate source leakage at 20 V and at 30 Vplus or minus 100 nA and plus or minus 1 microamp
Drain leakage at 650 V, 25 C and 125 C1 microamp and 25 microamp
Forward transconductance at 24 A16.7 S typical
Input, output and reverse transfer capacitance5182, 251 and 1 pF
Effective output capacitance, energy and time related192 and 665 pF
Total gate charge at 10 V, 520 V and 24 A172 nC typical, 263 maximum
Gate source and gate drain charge41 and 72 nC
Turn on delay at 520 V and 6 A37 ns typical, 84 maximum
Rise time, same conditions77 ns typical, 121 maximum
Turn off delay and fall time156 and 93 ns typical
Internal gate resistance at 1 MHz0.64 ohm
Continuous source drain diode current47 A
Pulsed diode forward current139 A
Body diode forward drop at 24 A0.9 V typical, 1.2 maximum
Reverse recovery time at 24 A and 25 V753 ns typical, 1506 maximum
Reverse recovery charge and peak current14 microcoulomb typical, 28 maximum, and 28 A
Single pulse avalanche energy, 28.2 mH and 10 A1410 mJ
Maximum power dissipation, case at 25 C417 W
Junction to case and junction to ambient0.3 and 40 C per watt
Continuous drain current at 25 C and 100 C case46 A and 29 A
Linear derating factor3.3 W per C
Operating junction and storage rangeminus 55 to plus 150 C

417 W at the case and 3.1 W in the air

The 0.3 C per watt junction to case figure is the best in this shipment and it is what allows 417 W at a 25 C case, but the ambient row is the one that decides a board. 40 C per watt allows 3.125 W for a 125 C rise, which is 6.68 A at 25 C and 5.6 A at a 50 C ambient. The gap between 46 A and 6.7 A is a factor of seven and it is entirely the heatsink.

At 46 A the channel sheds 148 W, which through 0.3 C per watt is 44.5 C of rise, so the case has to sit at 105 C to keep the junction at 150 C. That is a heatsink with forced air, and it is the reason the part is found in welding and induction heating equipment rather than in a sealed adapter.

The linear derating factor of 3.3 W per C is 417 W over 125 C, and it matches the thermal pair. The sheet prints no hot on resistance row, so the 0.07 ohm is a 25 C figure and the operating value has to come from the normalized curve, which for a super junction die of this class is close to 2.2 times at 150 C. That takes the conducting loss at 46 A from 148 W to a figure the case cannot remove, which is another way of saying the 46 A row is a 25 C case row and nothing more.

A diode that rules this part out of a bridge

Recovery is 753 ns typical and 1506 ns maximum at 24 A with a 25 V reverse voltage, with 14 microcoulomb of charge and 28 A of peak reverse current. Against the fast diode members of the same family, which print 80 to 90 ns and 5.8 microcoulomb, this is a slow diode and it is meant to be: the sheet does not claim a fast diode and the applications list avoids circuits where the body diode conducts.

The test condition is worth reading carefully. 25 V of reverse voltage is low for a 600 V part, and the recovery time of a super junction diode grows with the reverse voltage, so a bridge at 400 V will see more than 753 ns and more than 14 microcoulomb. A customer who measured 753 ns in a 400 V bridge and found less would be measuring something else.

Gate charge of 172 nC typical against 263 nC maximum is a 53 per cent spread, and 72 nC of gate drain charge against 41 nC of gate source charge is a long Miller plateau. At 24 A and 65 kHz the drive power is 0.112 W typical and 0.171 W worst case, so a 0.5 A driver is needed to keep the 77 ns rise time, and a 0.2 A driver will stretch the edge and the loss with it.

Where the slow diode is not a problem

A continuous conduction power factor stage, a two switch forward converter, an induction heater and a welding supply all keep the body diode out of the conduction path, so the 753 ns costs nothing. In the two switch forward the diode clamps the primary during the off time through a separate path, and in the PFC the boost diode carries the current, so the MOSFET diode never conducts.

Where it is a problem is a half bridge, a full bridge, a synchronous buck above 100 V, or any resonant stage that relies on the body diode during dead time. In those the recovery charge lands on the opposite switch and produces a spike that a 600 V rating will not absorb at 400 V, so a fast diode part or a silicon carbide diode is required.

Our power management cross reference work records which of the two diodes a part carries before any substitution is proposed, because replacing a fast diode part with this one keeps the on resistance and changes the recovery by a factor of eight, which is the sort of swap that fails on the first switching cycle.

Questions we answer before a reel is booked

First, the voltage. A part whose summary says 600 V and whose specification table says 650 V has to be settled before a build is released, because the creepage, the snubber and the surge absorber all follow the lower figure. We quote 600 V for this part and say the 650 V row is a template artefact until the vendor confirms otherwise in writing.

Second, the avalanche row closes. 1410 mJ against 28.2 mH and 10 A is exactly one half of 28.2 mH times 100, so the printed figure matches its stated test and this is the only 600 V sheet in the shipment where that is true. A repetitive avalanche in a welding supply can therefore be budgeted against it, subject to the 1 per cent duty note.

Third, the alternate. A 600 V part at 0.07 ohm with a slow diode is not interchangeable with a fast diode part of the same voltage, and the difference is 14 against 5.8 microcoulomb of charge. We hold the recovery behaviour per approved alternate, the incoming inspection plan checks the lot against it, and the pin to pin comparison starts from the tab and the 300 C soldering note, since this body is rated hotter at the leads than the rest of the family.