VBP165C30
Product Specifications
VBP165C30
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP165C30 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP165C30: 650 V silicon carbide in a TO247
The VBP165C30 is a single N channel silicon carbide MOSFET in a TO247 body rated at 650 V drain to source, a gate window of minus 10 V to plus 20 V, a threshold of 2 to 5 V and an on resistance of 70 milliohm at an 18 V gate. The structure is listed as SiC.
The catalogue page is not internally consistent on the current. The parameter table prints 30 A in the current column, and the text under it prints a maximum drain current of 70 A for the same part number. The two figures cannot both describe the same die, and this page reports the table as the working figure and the text as a discrepancy rather than picking whichever is more convenient.
At 30 A and 70 milliohm the die makes 63 W. At 15 A it makes 15.8 W, at 10 A it makes 7 W, at 5 A it makes 1.8 W. At the 70 A printed in the text the same resistance would give 343 W, which no TO247 removes, so the 30 A column is the figure that belongs in a thermal calculation.
Key data for the VBP165C30
| Configuration | Single N channel |
| Package | TO247, bolted to a heatsink |
| VDS | 650 V |
| VGE | Minus 10 V to plus 20 V |
| Vth | 2 to 5 V |
| ID | 30 A in the table, 70 A in the page text, to be confirmed on the data sheet |
| RDS(on) at 18 V | 70 milliohm |
| Technology | Silicon carbide |
| Loss at 5 A | 1.8 W |
| Loss at 10 A | 7 W |
| Loss at 15 A | 15.8 W |
| Loss at 30 A | 63 W |
650 V silicon carbide against 650 V silicon
A 650 V silicon superjunction part prints 80 to 200 milliohm at 30 to 40 A, so on resistance alone the two technologies are close at this voltage. The difference is switching. A silicon superjunction die has a output capacitance that is large for its resistance, and it loses that energy at every hard turn on; a silicon carbide die of the same resistance has roughly a third of the capacitance for the same voltage.
At 50 kHz the difference is small. At 200 kHz the silicon part spends more energy charging and discharging its own capacitance than the silicon carbide part spends conducting, which is why 650 V silicon carbide appears in server supplies, on board chargers and compact motor drives rather than in low frequency converters where silicon is cheaper.
The gate is the price. Silicon carbide needs 18 V on and a negative off bias, its threshold spreads from 2 to 5 V between parts, and the gate oxide is thinner for the same threshold. A driver built for a silicon part at 10 V will not reach the printed resistance, and one that rings to 25 V will damage the gate.
There is a second consequence of the higher capacitance at 650 V silicon. In a hard switched half bridge the turn on of the high side device discharges the low side output capacitance through both devices, and that current adds to the switching loss on every cycle. A silicon carbide part halves that term against silicon and does not remove it, so a 200 kHz converter still has to be laid out for the displacement current in the bridge.
The current figure has to be settled before a BOM
The table says 30 A and the text says 70 A. In a 650 V TO247 body, 70 A continuous would mean 343 W at 70 milliohm, which is not a real operating point; even 30 A at 63 W is at the top of what a good sink handles. The 70 A figure is likely a pulse or a die limit at a fixed case temperature, and it does not describe a socket.
For a purchasing decision the figure to carry is the resistance and the thermal path. At 15 A the loss is 15.8 W and a 0.6 C per watt path holds it with the junction 10 C above the case. At 20 A it is 28 W and the case has to stay near 80 C. Above that a second device in parallel is the answer, not a higher current column.
Because the two numbers on the page disagree, the safe route is to ask for the data sheet revision that both were taken from and to write the confirmed figure into the BOM comment. A part with a disputed current rating is a part that will be questioned at incoming inspection.
Where the part fits and where it does not
It fits a 400 V bus inverter at 10 to 15 A, a server power supply front end, an on board charger, a compact motor drive at 50 to 100 kHz and a power factor stage at high frequency. It does not fit a 690 V line, a 30 A continuous load without a large sink, or a driver that cannot supply 18 V and a negative bias.
Where a silicon carbide part is bought against a silicon code, the comparison has to include the driver, the gate resistor and the board, because the switching gain is only realized when those change with it. Our supplier quality audit page covers what is verified at the source when a new wide bandgap line is qualified.
The sourcing side of this part is covered on the PCBA quote checklist. For a wide bandgap part quoted with the board, that page covers what has to be fixed before a price means anything.
Questions we get on this code
Is the current 30 A or 70 A? The table prints 30 A and the text prints 70 A. We quote the table and record the discrepancy rather than choosing the larger figure.
Can it be driven at 15 V? It can, and the resistance rises above the printed 70 milliohm. The figure applies at 18 V.
Is it worth it against silicon at 650 V? Above about 100 kHz yes. Below that a silicon superjunction part is cheaper and often lower loss.
What does the order carry? Part number, TO247, tube packing and the date code. We confirm both on the offer.