VBP112MC100
Product Specifications
VBP112MC100
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP112MC100 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP112MC100: 1200 V silicon carbide at 0.016 ohm and 142 A in a TO-247
The VBP112MC100 is a 1200 V N channel silicon carbide MOSFET in the TO-247 body. The summary prints 1200 V, 0.016 ohm at an 18 V gate and 200 nC of gate charge, and the absolute maximum table adds 142 A with the case at 25 C, 100 A with the case at 100 C, 310 A pulsed, 535 W of dissipation and a 175 C junction. That combination of voltage and on resistance is not available in silicon, which is the reason the part exists.
At 50 A this die sheds 40 W. A silicon 1200 V part of the same current class sits between 0.3 and 1.0 ohm and would shed 750 W to 2500 W, so the comparison is not close and it changes what the circuit can be. The applications on page one follow from it: a power factor stage feeding an 800 V bus, an EV charger rectifier, a string inverter, and a DC to DC converter that steps 800 V down to 400 V without a transformer the size of a shoebox.
The price of that performance is a narrow gate window. The gate to source limit is minus 10 V to plus 22 V, the recommended drive is 18 V on and minus 5 V off, and the internal gate resistance is 8.5 ohm. The upper limit leaves 4 V of margin above the recommended drive, so any ringing on the gate that exceeds 4 V over the rail is a reliability problem rather than a nuisance, and the external resistor and the loop have to be chosen with that in mind.
The parameter table in full
| Drain to source voltage | 1200 V |
| Gate to source voltage | minus 10 V to plus 22 V |
| On resistance at 18 V gate and 100 A | 0.016 ohm typical |
| Gate threshold at 5 mA | 2 V minimum, 4 V maximum |
| Gate leakage at plus 18 V and at minus 8 V | 100 nA maximum each |
| Drain leakage at 1200 V, 25 C and 125 C | 100 microamp and 200 microamp |
| Forward transconductance at 100 A | 50 S typical |
| Input, output and reverse transfer capacitance at 800 V | 6800, 300 and 15 pF |
| Effective output capacitance, energy and time related | 230 and 320 pF |
| Total gate charge at minus 5 V and 18 V, 800 V and 50 A | 200 nC typical |
| Gate source and gate drain charge | 80 and 60 nC |
| Turn on delay at 800 V and 50 A | 15 ns typical, 20 ns maximum |
| Rise time, same conditions | 40 ns typical |
| Turn off delay and fall time | 60 and 30 ns typical |
| Internal gate resistance at 1 MHz | 8.5 ohm |
| Continuous source drain diode current | 60 A |
| Pulsed diode forward current | 150 A |
| Diode forward voltage at 50 A | 4.1 V maximum |
| Reverse recovery time at 50 A and 1000 A per microsecond | 35 ns typical |
| Reverse recovery charge and peak current | 1.5 microcoulomb and 15 A |
| Single pulse avalanche energy, 0.5 mH | 625 mJ |
| Maximum power dissipation, case at 25 C | 535 W |
| Junction to case and junction to ambient | 0.28 and 62 C per watt |
| Drain source voltage slope, forward and reverse | 150 and 100 V per ns |
| Operating junction and storage range | minus 55 to plus 175 C |
| Peak soldering temperature for 10 s | 260 C |
What the thermal rows mean at 142 A and at 12 A
535 W through 0.28 C per watt is 149.8 C of rise, which is the 175 C junction reached from a 25 C case, so that row is the thermal path written out rather than a separate capability. Running 142 A through 0.016 ohm sheds 322 W and needs the case at 85 C, which is a real liquid or forced air heatsink and not a copper pour.
In still air the ambient path allows 2.42 W for a 150 C rise, which is 12.3 A through the 25 C on resistance and nearer 7 A once the die is hot. That gap between 142 A and 7 A is the whole story of a TO-247 silicon carbide part: the die is capable of far more than the package can remove, and the useful current is set by the mounting, not by the silicon.
The 175 C junction rating is 25 C above the silicon parts in this shipment, and it buys margin in a fault rather than continuous headroom. A short circuit that lifts the junction to 160 C is survivable here and is not on a 150 C part, which is why this device appears in charger circuits that must ride through a surge without a field failure.
The diode is the part of the story that is usually misread
Reverse recovery is 35 ns with 1.5 microcoulomb of charge and 15 A of peak reverse current at 50 A forward and a 1000 A per microsecond slope. Measured against the 600 V and 650 V silicon parts in this shipment, which print 80 to 753 ns and 5.8 to 28 microcoulomb, that is a factor of two to twenty in charge and it is the number that makes a hard switched bridge at 800 V possible at all.
The forward drop is the other side of it. 4.1 V maximum at 50 A is a silicon carbide body diode, and 50 A through 4.1 V is 205 W in a device that can only remove 535 W from a 25 C case. Any dead time long enough for the diode to carry the full load current is therefore a thermal event, so the channel has to be turned on before the current transfers, or a silicon carbide Schottky has to sit in parallel.
The gate charge of 200 nC at a 23 V swing costs 0.46 W of drive at 100 kHz, which a small isolated driver handles. The 80 nC of gate source charge against 60 nC of gate drain charge is a much flatter split than the silicon parts in this band, and it is the reason the switching waveform is clean at 40 ns rise time without a large external resistor.
Where a 1200 V silicon carbide switch pays for itself
A 7 kW charger front end that runs a continuous conduction PFC at 65 kHz, an 800 V to 400 V DC to DC stage in a server power shelf, and a three phase string inverter all gain from the on resistance and the recovery together, because both losses fall at once and the switching frequency can rise without a thermal penalty. In each of those the heatsink disappears or shrinks by a factor of three, which is where the cost difference is recovered.
Where it does not pay is a 400 V auxiliary supply of 20 W, where a 0.88 ohm silicon part at one tenth of the price does the same job, and any circuit that cannot provide a negative off bias, because the 2 V to 4 V threshold and 15 pF of reverse transfer capacitance will turn the device on through the Miller path at 150 V per ns.
Our power management cross reference work treats silicon carbide and silicon as two different parts, not as one cross reference, since the gate drive, the dead time and the diode behaviour all change together and a substitution that keeps only the voltage and the footprint will fail in the first hour.
Questions we answer before a reel is booked
First, the avalanche row closes exactly here. 625 mJ against a 0.5 mH inductor is 50 A of starting current, which is the sort of figure that can be checked on a test bench, and it is the only avalanche row in this shipment that reconciles with its own stated test on the first pass. We still ask for the test report before using it to justify a snubberless flyback.
Second, the off bias. A zero volt turn off is not an option at 150 V per ns with a 2 V threshold and 15 pF of reverse transfer capacitance, because the displacement current through that capacitance lifts the gate above threshold for the duration of the edge. The minus 5 V in the recommended drive is functional, not decorative, and the driver has to hold it during the whole off state.
Third, the alternate and the lot. Silicon carbide dies from different foundries carry different threshold drift and different body diode forward drop, and 4.1 V against 3.5 V changes the dead time budget. We hold both figures per approved alternate, the incoming inspection plan checks the lot against them, and the pin to pin comparison starts from the gate window and the source kelvin connection rather than from the outline.