Contact Us

HXC50093

Brand: Hisiwell
Hisiwell HXC50093 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50093 — Discrete & Power Semiconductors | Superb Automation

HXC50093

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50093 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50093: 10 W on a 50 V rail, measured as a pulse part from 960 to 1400 MHz

The HXC50093 is a 10 W, highly rugged, unmatched LDMOS device on a 50 V rail, filed for wideband commercial and industrial applications up to 2 GHz. The index row gives it 10 W, 50 V and CW, with no gain and no efficiency column filled. The document behind the page gives a different and much more specific picture: a preliminary revision, dated 18 November 2019, that measures the part from 960 to 1400 MHz as a pulse CW signal with a 10 microsecond width and a 10 per cent duty cycle, on a 48 V rail with 10 mA of quiescent current.

The difference between CW and a 10 per cent pulse is worth more than a footnote. A die measured at 10 per cent duty has a thermal load one tenth of the CW case, and the efficiency and gain numbers in that table are only reachable in a pulse system. A buyer who reads the index row, sees CW and 50 V, and builds a continuous carrier will find the part running hotter and compressing earlier than the table suggests. The page states the measurement conditions rather than repeating the index label.

What the document does establish is a useful and honest set of small signal and compression figures at nine frequencies, and a load mismatch test at 2000 MHz with a 10 to 1 VSWR at 10 W pulse output and no degradation. Together with the 110 V breakdown and the 3 degrees per watt thermal resistance, that is enough to specify the part properly, provided the pulse condition is carried into the specification.

The HXC50093 rows as the vendor publishes them

Part classLDMOS RF power transistor, unmatched, single ended, highly rugged
Output, index row10 W
Output in dBm, calculated40.00 dBm
Frequency range, index rowHF to 2 GHz
Frequency range measured, document960 to 1400 MHz, nine points
Drain rail, index row50 V
Rail used in the measurement, document48 V with 10 mA quiescent current
Signal used in the measurement, documentPulse CW, 10 microsecond width, 10 per cent duty
Gain at 1 dB compression, document15.3 dB at 960 MHz rising to 16.9 dB at 1200 MHz, 16.0 dB at 1400 MHz
Output at 1 dB compression, document43.2 to 44.4 dBm, which is 20.9 to 27.5 W
Output at 3 dB compression, document43.8 to 44.8 dBm, which is 24.0 to 30.2 W
Drain efficiency at 3 dB compression, document55.3 per cent at 960 MHz rising to 61.0 per cent at 1350 MHz
Drain to source breakdown, document115 V minimum at 1 mA, 110 V rating
Gate to source maximum, documentminus 10 V to plus 10 V
Junction temperature maximum, document225 degrees C
Case operating temperature, document150 degrees C
Thermal resistance, junction to case, document3 degrees C per watt, DC test at 85 degree case
Gate threshold voltage, document2.82 V at 600 microamps, 50 V drain
Gate quiescent voltage, document3.0 V at 10 mA, 48 V rail
Input capacitance, document11.4 pF at 40 V and 1 MHz
Output capacitance, document4.9 pF at 40 V and 1 MHz
Feedback capacitance, document0.05 pF at 40 V and 1 MHz
Load mismatch, document10 to 1 at 10 W pulse output at 2000 MHz, no degradation
ESD class, documentHuman body model Class 2
Package, documentEarless flanged ceramic, two leads, drain and gate with the source on the flange
Fixture, documentRogers RO4350B, 0.508 mm, 1 oz copper, ATC600F capacitors from 1 pF to 33 pF
Document statusRevision 1.0, preliminary, dated 18 November 2019
Document title against catalogue numberHX520010V against HXC50093, not explained by the vendor
Orderable addendumNone published

What 10 W on a 50 V rail asks of the load, and the compression figures that surprise

10 W into 50 ohm is 22.4 V rms and 31.6 V peak, which is 0.63 times a 50 V rail. That ratio is low: on a 50 V supply a 10 W die uses only a third of the available swing, so the part is running far from its voltage limit and the 110 V breakdown is not a constraint at all. The reason to put a 10 W die on a 50 V rail is not the swing, it is the current: 0.35 A at 57 per cent efficiency is a tenth of the current a 10 W part on a 28 V rail would draw at the same efficiency, and on a system where the 50 V bus already exists that is the cheaper arrangement.

The document's compression figures are higher than the catalogue wattage, and that is normal rather than contradictory. 43.2 to 44.4 dBm at 1 dB compression is 21 to 28 W, and 43.8 to 44.8 dBm at 3 dB is 24 to 30 W, on a part sold as 10 W. The catalogue number is the linear rating, the compression points are the ceiling, and the gap between them is 3.3 to 4.5 dB. In a pulse radar or an ISM applicator that runs the part into saturation, the ceiling is the number that matters, and it is on the document rather than on the index.

The 10 to 1 mismatch test at 2000 MHz is the strongest statement on the page. A part rated to survive a 10 to 1 load at all phase angles without degradation at 10 W is a part that will not fail on a mismatched applicator, which is the failure the ISM customer actually has. It does not remove the need to rate the output capacitors for the mismatch voltage: at 3 to 1 the peak reaches 95 V on a 50 V rail, and the capacitors see that even when the transistor survives it.

Thermal: 3 degrees per watt under a 10 per cent pulse

3 degrees per watt with 7.5 W of heat at 57 per cent efficiency gives a 22.6 degree rise, so at an 85 degree case the junction sits near 108 degrees against a 225 degree limit. That is the continuous case, which is already comfortable. Under the 10 per cent pulse in the document the average heat is a tenth of that, so the junction barely moves and the published efficiency is reachable.

The trap is a buyer who takes the pulse numbers and runs the part continuously at the same output. The heat becomes 7.5 W instead of 0.75 W averaged, the rise is 22.6 degrees instead of 2.3, and while the junction is still inside the limit, the efficiency at continuous duty will not be the 61 per cent printed in the table. Ask the vendor for a continuous measurement before a continuous product is committed, because a preliminary document from 2019 may not be the last word.

The flange is small on this package, two leads and a ceramic body, so the heat path goes through the flange into the board. A 0.508 mm RO4350B board with 1 oz copper, which is the fixture in the document, is the reference. A thinner board with less copper shifts the case temperature up and the 3 degrees per watt no longer describes the assembly.

Drive, gain and the frequency where the gain stops rising

Gain at 1 dB compression runs from 15.3 dB at 960 MHz up to 16.9 dB at 1200 MHz and then back to 16.0 dB at 1400 MHz. That shape, rising then falling, is the signature of an unmatched die with an input match that peaks in the middle of the measured band. The drive at 15.5 dB is 0.28 W, or 24.5 dBm, which is a comfortable level for a small driver stage.

Because the part is unmatched at both ports, the match in your own product decides where the gain peaks. The document gives the fixture, an 0.508 mm RO4350B board with ATC600F capacitors from 1 pF to 33 pF, so the reference network is reproducible rather than hidden. Copy the fixture first, measure it, then adjust. A gain budget built on the middle of the band without that step will be 1 to 2 dB optimistic at the edges.

Above 1400 MHz the document stops. The part is filed to 2 GHz and the mismatch test is at 2000 MHz, but no small signal or compression data is published above 1400 MHz. Treat anything above that as unmeasured until the vendor supplies data or your own sweep fills the gap.

Where the HXC50093 sits on the shelf

The 10 W rows on this shelf come in three rails and two topologies. The 12.5 V group has a 20 W single at 15 dB and 65 per cent, the 28 V group has the HXC50153 at 10 W with 23 dB and 63 per cent, and the 50 V group has this row with 15 to 17 dB and 55 to 61 per cent under pulse. The 28 V part is the one for a high gain, low drive socket, and this 50 V part is the one for a system that already carries a 50 V bus and a pulse waveform.

Read as a choice, this row is the one for a 10 W pulse socket on 50 V where the mismatch survival matters more than the gain, and where a vendor document filed under another name is acceptable once the incoming route is set up. A buyer who needs CW at the same power takes the 28 V row and gets 6 dB more gain; a buyer who needs 20 to 30 W in pulse takes the next rung on the 50 V shelf.

Before the purchase order goes out

Two procurement points follow. The document is a preliminary revision from 2019, so ask the vendor whether a later revision exists and whether the pulse conditions are the ones the part is released against; the status field on the page says preliminary because the document does. And no orderable addendum is published, so the tray quantity, the moisture level and the marking have to be confirmed in writing. The incoming route for a document and label mismatch is on the incoming inspection plan page, and the comparison against competing 10 W LDMOS parts is on the RF power transistor cross reference page. A buyer assembling a mixed pulse and CW bill of materials can place the whole list through the one stop RF supply route.