Contact Us

VBN1405

Brand: VBsemi
VBsemi VBN1405 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBN1405 — Discrete & Power Semiconductors | Superb Automation

VBN1405

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBN1405 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBN1405: 40 V, 5 milliohm and a 175 C junction in TO-262

The VBN1405 is a 40 V N channel trench MOSFET in the TO-262 body with 5 milliohm at a 10 V gate, 110 A continuous at a 25 C case and a junction rating of 175 C. The 175 C rating is the first thing to notice, because it changes every thermal calculation on the page: the allowed rise is 150 C, not 125 C, so the same package removes 20 percent more power before it derates.

The sheet is written for a low voltage, high current switch: a 24 V or 12 V rail, a battery disconnect, a synchronous rectifier in a 12 V output, a motor bridge leg. At 40 V the part covers a 24 V rail with 16 V of margin, which is enough for a hot plug transient but not for a 36 V rail.

The on resistance is printed at three temperatures, and that is the most useful thing on the sheet: 5 milliohm at 25 C, 8 milliohm at 125 C and 10.6 milliohm at 175 C. A calculation that uses the 25 C figure for a part that runs at 100 C underestimates the loss by 60 percent, and at 175 C it is worse than that, so the hot row is the only one that belongs in a thermal budget.

The parameter table in full

Drain to source voltage40 V
Gate to source voltage, continuousplus or minus 20 V
On resistance at 10 V gate and 20 A, 25 C0.005 ohm typical
On resistance at 10 V gate and 15 A, 125 C and 175 C0.008 and 0.0106 ohm
Gate threshold at 250 microamp1.0 V minimum, 2.0 V typical, 4.0 V maximum
Continuous drain current, case at 25 C and 125 C110 A and 70 A
Pulsed drain current300 A
Avalanche current into 0.1 mH50 A
Repetitive avalanche energy, 0.1 mH125 mJ
Maximum power dissipation, case at 25 C150 W
Maximum power dissipation, ambient at 25 C on a one inch board3.75 W
Junction to ambient, board mounted40 C per watt
Junction to case1 C per watt
Operating junction and storage rangeminus 55 to plus 175 C
Zero gate voltage drain current at 40 V and 25, 125 and 175 C1, 50 and 250 microamp
On state drain current at a 10 V gate120 A
Forward transconductance at 15 A20 S minimum, 50 S typical
Input, output and reverse transfer capacitance at 25 V3200, 600 and 320 pF
Total, gate source and gate drain charge at 50 A95, 37 and 21 nC
Gate resistance on the die1.7 ohm
Turn on delay and rise time at 20 V and 50 A20 and 95 ns typical, 30 and 145 ns maximum
Turn off delay and fall time, same conditions50 and 12 ns typical, 75 and 20 ns maximum
Continuous and pulsed source drain diode current100 and 300 A
Body diode forward drop at 30 A0.90 V typical, 1.50 V maximum
Body diode recovery time at 30 A40 ns typical, 60 ns maximum

Three resistance rows and what they do to the loss budget

At 20 A and 25 C the loss is 2 W. At 15 A and 125 C it is 1.8 W, and at 15 A and 175 C it is 2.4 W. The point of the three rows is that the loss curve is not linear in temperature: 5 milliohm at 25 C becomes 10.6 at 175 C, which is a factor of 2.1. A heatsink sized on the cold figure fails in the second hour.

At the 110 A rating the loss at 25 C is 60.5 W, which through 1 C per watt leaves the case at 114 C, and the junction at 175 C. At 70 A and a 125 C case the resistance is 8 milliohm, so the loss is 39.2 W and the case sits at 86 C. Both are consistent, which shows the derating in the current table follows the resistance curve rather than a rule of thumb.

In still air the 40 C per watt row allows 3.75 W for the 150 C rise, which is 27.4 A at 25 C and 21.6 A at 125 C resistance. That is a respectable figure for a leaded package, and it comes from the 175 C junction rather than from any thermal magic.

A 40 V part on a 24 V rail: what margin looks like

A 24 V rail with a 10 percent tolerance reaches 26.4 V, and a hot plug event on a long cable can double that for a few microseconds. 40 V covers the first comfortably and the second only with a transient suppressor. A 30 V part would not, and a 60 V part would cost twice the resistance at this current.

Inside that margin the part has to hold off the spike without avalanching: the repetitive avalanche row is 125 mJ at 50 A into 0.1 mH, and half of 0.1 mH times 50 A squared is exactly 125 mJ, so the row and the test conditions agree on this sheet, which is not true of every sheet in this catalogue. The threshold window of 1.0 V to 4.0 V is wide, and the typical of 2.0 V is the number a driver sees. A 4.5 V logic gate with a 10 percent sag reaches 4.05 V, which is above the 4.0 V maximum threshold, so the part is fully on but with little margin. Drive from 10 V where the loss matters.

The gate charge of 95 nC at 50 A is high for a low voltage part, and the 1.7 ohm internal gate resistance limits how fast an external resistor can charge it. At 100 kHz the drive costs 0.095 W, and a 1 A driver is enough; at 300 kHz the drive current becomes the limit before the switching loss does.

Where the 175 C junction earns its price

A motor bridge in a sealed enclosure, a battery disconnect next to a pack that reaches 80 C, an LED driver in a luminaire and a synchronous rectifier in a 12 V output all benefit from the 175 C rating. In each case the ambient is high and the heatsink is small, so the allowed rise is the resource that matters.

Against a 60 V part at the same current, this one saves resistance and gives up 20 V of margin. Against a 30 V part it doubles the margin and keeps the same footprint. The choice is set by the worst case transient on the rail, which for a 24 V battery system with a motor is the regenerative spike.

Where a customer is replacing an older 40 V part, the useful comparison is the resistance at their operating temperature, not at 25 C. Our power management cross reference work keeps the hot resistance and the avalanche energy per alternate, because those are the two figures that decide whether a substitution survives a summer in a sealed box.

Questions we answer before a reel is booked

First, the sourcing of the dissipation row. The 150 W figure carries a footnote that it is not production tested, so it comes from the model rather than from a measurement on every lot. Treat it as a ceiling and size the heatsink from the 3.75 W ambient row, which is a measured condition.

Second, the package. TO-262 is a leaded body with an exposed tab and no mounting hole, so the tab is clamped or soldered rather than screwed. A board that expects a bolt through the tab needs a different body, and the footprint is not the same as a TO-220.

Third, the second source. 40 V parts at 5 milliohm vary in the temperature coefficient of the resistance, which is the row that decides the hot loss. The incoming inspection plan and the verification steps for a drop in replacement measure the resistance at two temperatures, since a part that matches at 25 C can be 30 percent worse at 125 C.