Contact Us

VBN1302

Brand: VBsemi
VBsemi VBN1302 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBN1302 — Discrete & Power Semiconductors | Superb Automation

VBN1302

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBN1302 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBN1302: 30 V and 150 A with 2 milliohm in a TO262

The VBN1302 is a single N channel MOSFET in a TO262 outline, the member of the TO220 family whose tab is formed to be soldered to the board rather than bolted to a heatsink. Drain to source is 30 V, the gate window is plus or minus 20 V, the threshold is 1.7 V, the printed drain current is 150 A and the on resistance is 2 milliohm at a 10 V gate and 3 milliohm at 4.5 V. The die is trench.

A 1.7 V threshold is the lowest in this band and it is the figure that decides how the part is driven. At 1.7 V the channel starts to conduct well below a 3.3 V logic level, which means a 4.5 V gate is already deep into the on state and the part works on a 5 V rail without a driver. It also means the part can be turned on by noise, by a Miller pulse or by a gate left floating, which is the hazard that comes with a low threshold.

Thirty volts is the class for a 24 V bus with a transient margin, a 12 V rail with a large one, and a 19 V laptop rail. It is not the class for a 24 V battery system that charges to 29 V and sees a 40 V spike, where a 40 V or a 60 V part is the correct choice.

Key data for the VBN1302

ConfigurationSingle N channel
PackageTO262, tab soldered to the board
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID150 A, a die figure at a 25 C case
RDS(on) at 10 V2 milliohm
RDS(on) at 4.5 V3 milliohm
TechnologyTrench
Loss at 20 A0.8 W
Loss at 40 A3.2 W
Loss at 60 A7.2 W

What a soldered tab means for the thermal path

The TO262 keeps the TO220 die and lead frame and changes the tab so it can be reflowed or wave soldered flat to a copper area. That removes the screw, the washer and the thermal pad, and it puts the heat straight into the board instead of into a heatsink. For a low voltage part at 3 to 7 W it is the better path, because the copper area under the tab is usually bigger than the tab itself.

The figure that matters is the area of copper on both sides and the number of vias between them. A 400 square millimetre area on two ounce copper with a via array under the tab holds about 3 W with the junction at 110 C in still air. Doubling the area does not double the dissipation, because the board also has to lose the heat to the air, and the enclosure sets whether that happens.

At 60 A the loss is 7.2 W and the board alone becomes marginal. That is where a small aluminium bar clamped over the tab, or a heavier copper layer, earns its place. The printed 150 A corresponds to 45 W, which no board removes, so it stays a die figure.

Driving a part with a 1.7 V threshold

A low threshold is a gift and a risk. The gift is that a 4.5 V gate reaches 3 milliohm and a 5 V logic output can drive the part directly in a small load switch. The risk is that the gate sits only 1.7 V from conduction, so any coupled noise that reaches 2 V turns the part partly on.

Three measures make it safe. A pull down resistor of 10 to 100 kiloohm at the gate holds it off when the driver is inactive. A gate resistor limits the current the Miller capacitance can inject at a drain edge. A short gate loop with the return to the source pin reduces the inductance that turns a fast drain edge into a gate voltage.

In a synchronous buck the low side device is the one at risk, because its gate is held off while the drain swings from zero to the input voltage. At 24 V and a 10 ns edge the Miller current can be several hundred milliamps, and a 1.7 V threshold leaves very little room. An active pull down inside the driver is the usual answer, and a negative bias is not available in most low voltage drivers.

Where the part fits and where it does not

It fits a 12 V synchronous buck at 20 to 40 A, a 24 V brushed motor driver, a battery disconnect on a 24 V pack, a load switch on a 19 V rail, an ORing path in a redundant supply, and a hot swap stage on a 12 V backplane. It does not fit a 24 V battery that charges to 29 V with spikes, a 48 V rail, or a load near 150 A on a board.

Where this part replaces a TO220 code, the footprint changes and the copper area has to be reworked, so the comparison is mechanical as much as electrical. Our pin to pin cross reference page covers what has to match before a package change is accepted on an existing board.

The sourcing side of this part is covered on the kitting service. For a board that uses several low voltage parts, that page covers how the kit is built and checked.

Questions we get on this code

Is a 1.7 V threshold safe? Yes with a pull down at the gate and a short gate loop. It is the part that turns on easiest and therefore the one that needs the gate held firmly at zero.

Can it be driven from 3.3 V logic? Partly. At 3.3 V the resistance is above the 4.5 V figure, so the loss is higher than printed. A 5 V driver reaches the useful numbers.

How much copper does the tab need? About 400 square millimetres on two ounce copper with vias for 3 W, and more for 5 W. Above that a bar or a sink is needed.

What does the order carry? Part number, TO262, and tube packing. We confirm the packing on the offer.