Contact Us

VBMB18R18S

Brand: VBsemi
VBsemi VBMB18R18S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB18R18S — Discrete & Power Semiconductors | Superb Automation

VBMB18R18S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB18R18S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB18R18S: 800 V at 0.220 ohm with 3100 pF of input capacitance

The VBMB18R18S is an 800 V N channel super junction MOSFET in the TO-220F isolated body with 0.220 ohm at a 10 V gate and 18 A continuous at a 25 C case. It is the lower resistance member of the 800 V pair and the higher capacitance member at the same time, which is the trade a buyer has to see before choosing between the two.

Compared with the VBMB18R15S, this part cuts the on resistance by 42 percent and raises the input capacitance from 1720 pF to 3100 pF. In a 50 kHz hard switched stage the resistance wins. In a 200 kHz resonant stage the capacitance wins. The sheet prints the dissipation at 236 W against 208 W, which says the die is larger, and a larger die is what a lower resistance at the same voltage looks like.

The applications are the ones the family lists: server and telecom supplies, switch mode supplies, power factor correction, lighting and industrial. At 800 V and 0.22 ohm the natural home is a 600 V bus PFC or a two switch forward converter at 2 kW to 6 kW.

The parameter table in full

Drain to source voltage at maximum junction temperature800 V
Gate to source voltage, continuousplus or minus 30 V
On resistance at 10 V gate and 6 A, 25 C0.220 ohm typical
Gate threshold at 250 microamp2.5 V minimum, 4.5 V maximum
Continuous drain current, case at 25 C and 100 C18 A and 11 A
Pulsed drain current, repetitive54 A
Single pulse avalanche energy, 28.2 mH and 5 A start474 mJ
Maximum power dissipation, case at 25 C236 W
Linear derating factor1.67 W per C
Junction to case and junction to ambient0.7 and 62 C per watt
Operating junction and storage rangeminus 55 to plus 150 C
Zero gate voltage drain current at 800 V and at 640 V with a 125 C junction1 and 100 microamp
Drain source voltage slope, junction at 125 C50 V per ns
Reverse diode voltage slope15 V per ns
Input, output and reverse transfer capacitance3100, 80 and 4 pF
Effective output capacitance, energy and time related63 and 213 pF
Total gate charge at 10 V gate, 5 A drain and 520 V84 nC typical
Gate source charge15 nC
Gate drain chargenot printed on this sheet
Turn on delay and rise time at 520 V and 5 A18 and 24 ns typical, 25 and 55 ns maximum
Turn off delay and fall time, same conditions80 and 12 ns typical
Gate input resistance0.8 ohm
Continuous and pulsed source drain diode current18 and 54 A
Body diode forward drop at 5 A1.5 V maximum
Body diode recovery time, charge and peak current60 ns, 5.8 microcoulomb and 31 A
Forward transconductance at 6 A6.5 S
Peak soldering temperature for 10 s260 C

Conduction loss at the currents that matter

At 6 A, the current where the resistance is specified, the loss is 7.9 W, which needs a case below 144 C through the 0.7 C per watt path. At 11 A, the 100 C case rating, the loss is 26.6 W and the case has to stay under 131 C. At the 18 A rating the loss is 71.3 W and the case must be below 100 C.

In still air the 62 C per watt row allows 2.02 W, which is 3.03 A at 25 C. That is the honest figure for a board with no heatsink. A 6 A load in still air is 7.9 W and needs metal, which is the same conclusion as on the rest of the family.

The 100 microamp leakage row at a 125 C junction and 640 V is higher than the 10 microamp printed by the 0.38 ohm sibling. That is a property of a larger die area at the same process: more area, more leakage. In a high temperature standby application the leakage has to be counted in the off state loss, which is 0.064 W at 640 V.

A 60 ns recovery row on an 800 V device

The recovery time of 60 ns is the fastest printed on any of the 800 V or 600 V members of this family, and it sits against 5.8 microcoulomb of charge and 31 A of peak reverse current. A fast recovery time with a large charge is not a contradiction: the time is short because the current is high, and the charge is what the opposite switch has to absorb. At 50 kHz and 600 V, 5.8 microcoulomb is 0.17 W in the diode, and the 31 A peak lands on the switch that turns on.

The turn off delay of 80 ns with a 12 ns fall is the same as the 0.38 ohm sibling, and the gate charge of 84 nC at 5 A is higher than the sibling's 48 nC because the die is larger and the test current is lower. When a driver is sized, use the 84 nC figure with the 10 V gate and accept that the spread across lots can be 1.5 times.

Taken together, the two figures say the die is built for conduction: 0.22 ohm with 3100 pF is a larger area carrying a larger gate charge, and the sheet prints 236 W against 208 W on the smaller member to match. The capacitance row is the reason this part is not a 200 kHz device. At 3100 pF of input capacitance and a 500 V swing, the energy stored in the output capacitance is charged and discharged every cycle, and at 200 kHz that alone is several watts. The 0.22 ohm wins in conduction, and at 200 kHz the capacitance takes the saving back.

Choosing between the two 800 V members

Take the 0.22 ohm part when the switch conducts more than 30 percent of the period and the frequency is below 100 kHz. Take the 0.38 ohm part when the duty is short, the frequency is high, or the drive is weak, because 1720 pF needs less gate current than 3100 pF at the same edge rate.

Both parts share the same 2.5 V to 4.5 V threshold window, the same 0.8 ohm internal gate resistance and the same 1.5 V diode drop, so a board can carry either without a drive change. What changes is the loss split, and that is an arithmetic question for the customer's waveform, not a question the sheet answers.

Where a customer is consolidating two 800 V parts into one, our power management cross reference work compares them at the actual duty and frequency rather than at the headline current, since the capacitance and the resistance pull in opposite directions.

Questions we answer before a reel is booked

First, the gate charge test current. 84 nC is measured at 5 A, and a super junction gate charge rises with the drain current because the miller plateau lengthens. At 11 A the figure is higher, so a driver sized on 84 nC with a 20 percent margin is not oversized.

Second, the leakage at temperature. 100 microamp at 640 V and a 125 C junction is a real off state loss, and in a standby product that runs warm it has to be part of the budget. A 10 microamp assumption from the sibling part underestimates it by a factor of ten.

Third, the gate under a short. The 0.8 ohm internal resistor and the 15 nC of gate source charge describe a gate that opens on a fast edge, so a 20 A short through the channel is cleared by the driver and not by the part. Ask for the short circuit waveform on the driver you intend to use, because the destruction usually starts in the gate loop rather than in the die, and a clamp diode on the gate is cheaper than a new board.

Fourth, the second source. 800 V super junction parts at 0.22 ohm vary by a factor of three in recovery charge, and the recovery is what fails a bridge at turn on. The incoming inspection plan and the pin to pin comparison hold the recovery and the capacitance per approved alternate, so a substitute is compared on the rows that decide the loss.