Contact Us

VBMB18R15S

Brand: VBsemi
VBsemi VBMB18R15S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB18R15S — Discrete & Power Semiconductors | Superb Automation

VBMB18R15S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB18R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB18R15S: 800 V at 0.38 ohm in three bodies sharing one table

The VBMB18R15S is an 800 V N channel super junction MOSFET with 0.38 ohm at a 10 V gate and a 15 A continuous rating at a 25 C case. One sheet covers three strings: VBM18R15S in TO-220AB, VBMB18R15S in TO-220F and VBP18R15S in TO-247AC, and one column of limits is printed for all three.

An 800 V part is not chosen for a 400 V bus. It is chosen when the bus is 600 V, when the input is a 480 V three phase line that rectifies to 680 V, or when a 400 V stage has to survive an energy dump from a motor with no brake resistor. At 800 V and 0.38 ohm the part pays for that margin in conduction loss, and the sheet is honest about the trade: 15 A at a 25 C case and 12 A at 100 C, with a 208 W dissipation row that belongs to the exposed tab bodies.

The features list claims a low figure of merit, a low input capacitance and avalanche energy rated. The capacitance row of 1720 pF is what makes the claim hold at 800 V, since most parts in this class print twice that.

The parameter table in full

Drain to source voltage at maximum junction temperature800 V
Gate to source voltage, continuousplus or minus 30 V
On resistance at 10 V gate and 8 A, 25 C0.38 ohm typical
Gate threshold at 250 microamp2 V minimum, 4 V maximum
Continuous drain current, case at 25 C and 100 C15 A and 12 A
Pulsed drain current, repetitive46 A
Single pulse avalanche energy, 28.2 mH and 4.5 A start297 mJ
Maximum power dissipation, case at 25 C208 W
Linear derating factor1.7 W per C
Junction to case and junction to ambient0.7 and 62 C per watt
Operating junction and storage rangeminus 55 to plus 150 C
Zero gate voltage drain current at 800 V and at 520 V with a 125 C junction1 and 10 microamp
Drain source voltage slope, junction at 125 C37 V per ns
Reverse diode voltage slope26 V per ns
Input, output and reverse transfer capacitance1720, 80 and 4 pF
Effective output capacitance, energy and time related63 and 213 pF
Total gate charge, typical and maximum at 10 V48 and 96 nC
Gate source and gate drain charge11 and 21 nC
Turn on delay and rise time at 520 V and 8 A18 and 24 ns typical, 36 and 48 ns maximum
Turn off delay and fall time, same conditions48 and 25 ns typical, 96 and 50 ns maximum
Gate input resistance0.8 ohm
Continuous and pulsed source drain diode current15 and 46 A
Body diode forward drop at 8 A1.2 V maximum
Body diode recovery time, charge and peak current325 ns, 4.6 microcoulomb and 20 A
Forward transconductance at 8 A6.3 S
Peak soldering temperature for 10 s300 C

What 0.38 ohm costs on a 600 V bus

At 8 A, which is the current where the resistance is specified, the channel sheds 24.3 W. That needs a case below 133 C through the 0.7 C per watt path, so the part belongs on a heatsink in any circuit above a few amps. At the 15 A rating the loss is 85.5 W and the case has to stay under 90 C. At a 1 A standby load the loss is 0.38 W and the part is cool anywhere.

In still air the 62 C per watt row allows 2.02 W, which is 2.3 A at 25 C. A customer who asks whether this part can replace a 600 V device at 5 A on the same tab gets an arithmetic answer: 5 A is 9.5 W and needs the case under 143 C, which is a heatsink, not a pour.

The 208 W dissipation row belongs to the exposed tab bodies. The Fullpak string on the same sheet carries the same electrical table but not the same thermal path, so a qualification that used a TO-220AB reference board does not transfer to the isolated body without a new measurement.

The switching block is shared, the capacitance is not

The gate charge of 48 nC typical and 96 nC maximum, the 11 and 21 nC components, the 40 ns delay chain and the 5.8 microcoulomb recovery appear with the same values on the 600 V, 650 V, 700 V and 800 V sheets of this family. That is worth knowing before a comparison table is built: the dynamic block on these sheets does not separate the members, and the rows that do separate them are the on resistance, the input capacitance and the diode recovery time.

On this sheet the recovery is 325 ns with 4.6 microcoulomb and 20 A of peak current, which is slower than the 650 V fast diode member at 90 ns and faster than the 600 V plain member at 475 ns. For a hard switched bridge on a 600 V bus, 4.6 microcoulomb at 40 kHz and 600 V is 0.11 W in the diode plus the spike that lands on the opposite switch.

The input capacitance of 1720 pF at 100 V is the figure that makes an 800 V part usable at 40 kHz to 60 kHz. At 100 kHz the drive loss from 96 nC at 10 V is 0.096 W, and the switching loss in the channel becomes the dominant term, which is why the sheet does not list server supplies at 300 kHz among its applications.

Where 800 V is the right answer

A 480 V three phase input with a 680 V rectified bus, a 600 V DC distribution, a welder with a high leakage transformer, and a motor drive with an energy dump all need 800 V. In each case a 650 V part would need a clamp, a snubber or a slower edge, and the 0.38 ohm is cheaper than any of those.

It is also the correct choice where the same board has to run from a 400 V bus in one market and a 480 V line in another. The extra voltage covers both without a second bill of materials, and the 12 A row at a 100 C case is enough for the 2 kW to 4 kW supplies that use this platform.

Against the 800 V VBMB18R18S this part gives up 0.16 ohm and 28 W of dissipation and gains 47 percent lower input capacitance. Against the 700 V VBMB17R15SE it gives up 100 V of headroom in exchange for a slower diode and a higher resistance, which makes it the wrong choice for a 540 V bus. Our power management cross reference work keeps the voltage, the capacitance and the recovery side by side so the comparison lands on the row that decides the circuit.

Questions we answer before a reel is booked

First, the body. Three strings, one table. A drawing that calls out an isolated Fullpak needs the VBMB string, and the 208 W row printed on page one does not apply to it. Ask for the string and the package note before quoting a current.

Second, the avalanche row. 297 mJ is printed against 28.2 mH and 4.5 A, which stores 286 mJ, so the printed figure is marginally above what the stated test can deliver. Treat it as a single pulse ceiling and not as a repetitive rating, and check the repetitive curve for any circuit that avalanches every cycle.

Third, the second source. 800 V parts at 0.38 ohm come from several suppliers, and the recovery time and the threshold window differ more than the resistance. The verification steps for a drop in replacement and the lead time work hold the recovery and the capacitance per approved alternate, because at 800 V those two decide the switching loss.