Contact Us

VBMB1806

Brand: VBsemi
VBsemi VBMB1806 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB1806 — Discrete & Power Semiconductors | Superb Automation

VBMB1806

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB1806 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB1806: 80 V, 6.4 milliohm and a package that sets the current

The VBMB1806 is a trench N channel MOSFET rated 80 V, with 6.4 milliohm at a 10 V gate and a 75 A continuous row that carries a package limited note. It is not a super junction device and it does not pretend to be: at 80 V the trench process is the right answer, and the interesting numbers on the sheet are the ones that show where the leadframe, not the die, decides the current.

The sheet lists primary side switching, synchronous rectification, DC to AC inverters and LED backlighting. In every one of those the part works as a synchronous rectifier or a low side switch in a converter whose input is a 24 V or 48 V rail, so the 80 V rating covers the flyback spike and the reverse recovery of the opposite diode.

Three bodies of the 75 A row tell the real story: 75 A at a 25 C case, 62.7 A at a 70 C case, 28.6 A at a 25 C ambient on a one inch square board for 10 s, and 24.9 A at a 70 C ambient. The last two are the ones a board actually sees, and they are a third of the headline.

The parameter table in full

Drain to source voltage80 V
Gate to source voltage, continuousplus or minus 20 V
On resistance at 10 V gate and 20 A0.0064 ohm typical
On resistance at 6 V gate and 15 A0.0070 ohm typical
On resistance at 4.5 V gate and 10 A0.0087 ohm typical
Gate threshold at 250 microamp1.4 V minimum, 2.6 V maximum
Continuous drain current, case at 25 C and 70 C75 A package limited and 62.7 A
Continuous drain current, ambient at 25 C and 70 C28.6 A and 24.9 A on a one inch board
Pulsed drain current for 100 microsecond150 A
Single pulse avalanche current into 0.1 mH30 A
Single pulse avalanche energy45 mJ
Maximum power dissipation, case at 25 C and 70 C62.5 W and 40 W
Maximum power dissipation, ambient at 25 C and 70 C5 W and 3.2 W
Junction to ambient for 10 s on a one inch board20 C per watt typical, 25 maximum
Junction to case, steady state1.5 C per watt typical, 2 maximum
Operating junction and storage rangeminus 55 to plus 150 C
Input, output and reverse transfer capacitance at 40 V1855, 950 and 76 pF
Total gate charge at 10, 6 and 4.5 V gate35.5, 22 and 17.1 nC typical
Gate charge maximum at the same three gate levels54, 33 and 26 nC
Gate source and gate drain charge5.3 and 7.3 nC
Output charge at 40 V57 nC typical, 86 maximum
Gate resistance on the die1.3 ohm typical, 2 maximum
Turn on delay and rise time at a 10 V gate12 and 8 ns typical, 24 and 16 maximum
Turn off delay and fall time at a 10 V gate32 and 7 ns typical, 64 and 14 maximum
Turn on delay and rise time at a 6 V gate14 and 11 ns typical
Body diode drop at 5 A0.76 V typical, 1.1 V maximum
Body diode recovery time and charge at 10 A38 and 75 ns, 36 and 70 nC
Peak soldering temperature for 10 s260 C

A thermal file that closes on itself

This is the rare sheet where the arithmetic checks out. 25 C per watt maximum from junction to ambient with a 125 C rise allows 5 W, and the dissipation table prints 5 W at a 25 C ambient. Working back through 0.0064 ohm, 5 W carries 27.9 A, and the current table prints 28.6 A at the same condition. The two rows agree because they come from one model, which makes the sheet usable without a leap of faith.

The avalanche row closes too: half of 0.1 mH times 30 A squared is 45 mJ, exactly the energy printed. Where the super junction sheets on the same books print avalanche energies above what the stated test can store, this one can be used to size a clamp for a relay or a small transformer, within the single pulse figure and the repetitive derating.

The case rows tell the other half of the story. 62.5 W at a 25 C case with 2 C per watt maximum gives a 125 C rise, so the package is limited by the leadframe and the die attach rather than by the channel. The 75 A row is explicitly package limited, and the 150 A pulse row is set by the same lead.

The gate is the differentiator at 4.5 V

Three on resistance rows at three gate levels are printed for a reason. At 10 V the part is 6.4 milliohm, at 6 V it is 7.0, and at 4.5 V it is 8.7, which is 36 percent above the 10 V figure. A driver running from a 5 V rail with a 0.3 V drop lands near 4.7 V and gets the 8.7 milliohm row, and the conduction loss at 20 A rises from 2.56 W to 3.48 W.

The gate charge follows the same shape: 35.5 nC at 10 V, 22 nC at 6 V and 17.1 nC at 4.5 V. A 4.5 V drive therefore costs less charge and more resistance, and at 200 kHz the trade can go either way. At 100 kHz the resistance dominates and 10 V wins.

The gate resistance on the die is 1.3 ohm typical and 2 ohm maximum, and the turn off delay of 32 ns with a 7 ns fall at a 10 V gate says the die is fast. With 76 pF of reverse transfer capacitance the miller plateau is short, so a 1 A driver is enough and a 4 A driver buys nothing except a faster edge that the loop inductance will ring anyway.

Where an 80 V trench switch at 6.4 milliohm belongs

A 48 V input synchronous buck for a telecom board, a 24 V battery disconnect, a synchronous rectifier in a 12 V output flyback and an LED backlight boost all fit inside the envelope. In each case the switch conducts for most of the cycle, so the 6.4 milliohm matters more than the switching charge, and the 80 V rating covers the spike without a snubber.

Against a 60 V part of the same current, this one gives 20 V of extra margin for the same resistance class, which is what a 48 V rail with a 60 V transient needs. Against a 100 V part it saves resistance at the cost of margin. The choice is made by the worst case spike, not by the nominal rail.

Where a customer has an existing 75 A part in the same Fullpak footprint, the useful comparison is the on resistance at the gate voltage they actually drive, not at 10 V. Our power management cross reference work records the resistance at three gate levels for every alternate, because a 4.5 V drive turns a 6.4 milliohm part into an 8.7 milliohm part.

Questions we answer before a reel is booked

First, the current. The 75 A row is package limited and sits on a 25 C case. A board that carries 20 A at a 70 C ambient is inside the 24.9 A row with little margin, so the copper and the airflow have to be part of the qualification, not an afterthought.

Second, the gate. A threshold window of 1.4 V to 2.6 V is low enough that a 3.3 V rail can turn the part partly on through a slow edge, and a floating driver pin can do the same. Keep a pull down on the gate and check the driver's undervoltage lockout against the 2.6 V maximum threshold.

Third, the second source. 80 V trench parts at 6.4 milliohm vary in gate charge and in the resistance at 4.5 V, which is the row that matters in a 5 V driven stage. The incoming inspection plan and the pin to pin comparison hold the three gate levels side by side, so a substitute is judged on the row the circuit runs at.